EgotisticBAMF

Meister Edel

This is a 3D Printable Hinge to be upright printable. This way I can keep the tolerances small, the hinge is very stiff and stable. But the biggest advantage is that you can print lots of them at the same time!&nbsp;Care not to tighten the screws too hard. That could weaken the hinge.

 Stable Hinge !upright printable!

Good Hardware

cartyski

My crystal hand ring stand was previously scaled too large and lacked stability. I have reduced the size and added a hex base to refine this beautiful sculpture.&nbsp;The rings pictured are size 10 for reference.

Crystal Hand Ring Stand v2

Multi colored filament

ninjake

I wanted my holster to be easy to print with little to no post processing. After a few versions I realized I also needed the belt buckle area able to print clean with no supports required so as not to scratch up my belt. This model was made to specifically print standing up utilizing a small brim so that no supports are needed for printing. &nbsp;This has been pretty handy as an easy way to keep my rod/reel off the ground/sand/beach while swapping lures and being able to use two hands in removing stubborn hook sets. I also wanted it to be angled forward just enough to keep the rod usable and/or out of the way while it&#39;s holstered.&nbsp;Hope you enjoy and tight lines!&nbsp;------------------------------------------------------------------------------------&nbsp;V2 released with Waist Clip - No Belt needed! <a target="_blank" href="https://makerworld.com/en/models/494357#profileId-408308" rel="nofollow noopener">https://makerworld.com/en/models/494357#profileId-408308</a><img class="image_resized" style="width: 21.84%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000473155/design/2024-06-13_fd0883a5b1815.jpg">&nbsp;&nbsp;----------------------------------------------------------------------------------------&nbsp;Had several requests for commercial use access so here ya go! Buy once, sell forever.&nbsp;***Commercial License now available for purchase on Cults***<a target="_blank" href="https://cults3d.com/en/3d-model/various/fishing-rod-belt-holster-ninjakegraff" rel="nofollow noopener">https://cults3d.com/en/3d-model/various/fishing-rod-belt-holster-ninjakegraff</a>

Fishing Rod Belt Holster

Schmitty 3D Printing

This is Storage for a middle console in a Hyundai Tucson built since 2021 &amp; Hyundai Santa Cruz&nbsp;Edit: Many thanks to user_2933333244 for information that is compatible with a Hyundai Santa Cruz&nbsp;Have fun by printing.&nbsp;Printing Files for 2 Storage

Middle Console Storage Tucson 2021+ & Santa Cruz

truck

Jorge Rui

<h3>Introduction</h3>I bring you something very simple and utilitarian. As with previous projects, there&#39;s already a proliferation of similar items on 3D printing websites. – This is a card wallet featuring a clip that can be used both to securely close the wallet and to hold a few banknotes.I took this opportunity to use carbon fiber effect build plates. Although “faux finishes” aren&#39;t typically my favorite thing, the aesthetic result is interesting, and I was eager to experiment with some build plates that I have and this wallet project provided the perfect excuse.I&#39;ve used the Carbon Fiber Surface from <a target="_blank" href="https://shrsl.com/4kcmz" rel="nofollow noopener">Bambu 3D Effect Sheet</a><figure class="image image_resized" style="width: 25.95%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000484840/design/2024-06-04_ef54f78707e49.png"></figure>The assembly is straightforward and can accommodate five cards, with the option to adjust for more or fewer cards, at the moment you can use the scale tool at the correct axis on the slicer of you preference.&nbsp;<a target="_blank" href="https://youtu.be/6ih9Qji1UNE?si=aSGusJf2BXTL5wcs" rel="nofollow noopener">Inserting and removing cards clip</a>&nbsp;A larger version, for 10 cards will be made available in a couple of days.I know it might seem like the cards are punctured, but that&#39;s not the case. Instead, &#34;blisters&#34; are used for each card, allowing for easy handling without the risk of them falling out.<figure class="image image_resized" style="width: 39.19%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000484840/design/2024-06-04_3f4b14e0d66e8.png"></figure><h3>Variations and Material used:</h3>The dark material used is the fantastic<a target="_blank" href="https://shrsl.com/4cvrd" rel="nofollow noopener"> &#34;Lava Grey,&#34; which is PLA+CF</a> from Bambu Lab. However, you can use any material of your preference (PLA).I chose this one for its deep matte finish. On the other hand, I know I lost some of the three-dimensional effect offered by the 3D build plate. Nonetheless, I personally prefer the subdued effect. If you desire maximum impact, then use regular PLA (be careful, these build plates are not suitable for PETG). Any of the <a target="_blank" href="https://shrsl.com/4ctbi" rel="nofollow noopener">Bambu lab regular PLA</a> with the color of your choice will do, this red if the Prusament.&nbsp;<h3>Assembling</h3>The assembly is quite simple. There is only one consideration, which may depend on your printer. In some cases, the nut might offer some resistance when being screwed in. However, it&#39;s just a matter of patience and applying a bit more tightening force. If it proves impossible, first check if the thread was printed correctly or if there&#39;s any filament out of place. If necessary, you can adjust the scale on the two lateral axes to widen it.&nbsp;<a target="_blank" href="https://youtu.be/sa2iDvdLZCk" rel="nofollow noopener">Assembling clip</a><h4>Support the designer:</h4>This design is free for the benefit of the community, but If you like my designs and want to contribute, you can make a donation to <a target="_blank" href="https://www.buymeacoffee.com/designrepcom" rel="nofollow noopener">buymeacoffee </a>or <a target="_blank" href="https://www.paypal.com/donate/?business=BUM67EMDJRXSN&amp;no_recurring=0&amp;currency_code=EUR" rel="nofollow noopener">paypal, </a>or even better, join “My Club” here in printables.com, that will be greatly appreciated.<h3>Change Log</h3><ul><li>(04-06-2024)- Initial Release</li></ul>

A Simple Wallet

work

Cloudy Nostalgia

How to support me!If you like my work, consider joining my Patreon where you can have a say in what I print next! Only Patreon members get to see those items and you can even sell them at a certain tier. Finally, if you’d like to learn my tips and tricks for making a hueforge start to finish I offer a coaching session to some of my patreons! Thank you for all your support!<a target="_blank" href="http://www.patreon.com/CloudyNostalgia" rel="nofollow noopener">www.patreon.com/CloudyNostalgia</a>&nbsp;Also, if you have any questions about how to print a piece of mine or if you need help troubleshooting, feel free to join my discord server where you can ask for help!<a target="_blank" href="https://discord.gg/4ays78UJ" rel="nofollow noopener">https://discord.gg/4ays78UJ</a>&nbsp;Also, I upload videos every so often showing how to videos for Hueforge. If you’d like to view here is the link:<a target="_blank" href="https://www.youtube.com/channel/UCG1IDrymVjUyYng7nXrdGnw" rel="nofollow noopener">https://www.youtube.com/channel/UCG1IDrymVjUyYng7nXrdGnw</a>&nbsp;**IMPORTANT INFORMATION**<ul><li>You cannot adjust the z scaling on any hueforge. This will mess with the coloring done and your hueforge will not come out as intended. You can however change the x and y to scale the picture. I recommend only changing by the same percentage. </li><li>To get an accurate print as shown in the photos you MUST use the same filaments listed below. You can change brands (as long as they are similar) but keep the filament colors the same. If you use any other color, you will not get the same results as me. </li><li>What you see in the slicer will not be how the final results will look! Hueforge takes advantage of color bleed to make the blended colors!</li></ul>Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmFilaments Used: PLA BambuLab Basic Black Transmission Distance: 0.6 PLA BambuLab Basic Orange Transmission Distance: 6.2 PLA BambuLab Basic Jade White Transmission Distance: 3.5Swap Instructions: Start with Black At layer #17 (1.44mm) swap to Orange At layer #23 (1.92mm) swap to Jade White for the rest.

Hueforge - Naruto - Side View

nweishar

Introducing my game-changing Wall Hanger for Resistance Band Grip Handles! Elevate your home gym experience with this 3D-printed marvel designed to revolutionize your workout space. No more tangled bands or cluttered corners – this hanger is the ultimate solution for organizing your resistance band grip handles.&nbsp;Why Choose My Wall Hanger?&nbsp;Space-Saving Brilliance: Say goodbye to the mess and reclaim your workout space. My Wall Hanger lets you neatly store your resistance band grip handles on the wall, freeing up the floor for more dynamic exercises.Effortless Installation: No need for complicated setups. I've designed this hanger for easy installation. Mount it on your wall, and you're ready to streamline your home gym.Built to Last: Crafted with precision through 3D printing, this hanger boasts durability that matches your toughest workouts. It's my commitment to quality, ensuring your fitness area stays organized for the long haul.Versatile Elegance: Beyond functionality, my Wall Hanger adds a touch of style to your workout space. Showcase your fitness gear with pride, turning your home gym into a visually appealing and motivating environment.Accommodates All Handles: Whether you have standard or custom grip handles, my hanger is designed to adapt. It's a versatile solution catering to various sizes and styles.

Resistance Band Handle Grip, Heavy Duty Cable Machine Attachment Wall Hangers

QuantumMercy

Lithophane frame that I have designed to hold 5 lithophanes (130x130x3mm) &nbsp;

Lithophane Frame for Light Box

lightboxes

WagZPrintZ

Dewalt 20V DCE100 Blower Foot! &nbsp;Whats it do!? This is just a simple fast print that allows your DCE100 20V dewalt blower to sit correctly. If you have one, and youve sat it down.. im sure you thought to yourself.. “Whys this stupid thing lean over?”…. &nbsp;Hows it work!? Its simple!! Ziptie this baby to the motor side of your dewalt blower with 2 zipties, or 1 big one, use a set of snips to really get it nice and snug, and boom… problem solved! Make sure you put it in that recessed area underneith so it dont move around to much. &nbsp;So how do you suggest printing it?! Me, myself, I recommend 6 walls, 6 top and bottom layers, and 25% honeycomb infill! Make that baby rigid! The included profile is setup to do so on the mini A1 printer with a nice brim on the textured plate! (You may not need a brim if you use a different plate or your one of them glue users….) &nbsp;If you make one, post a make please. I dont expect alot of folks to come rushing to make one.. lol. But if you do, ill bet ya like it! enjoy!

DeWalt DCE100 Blower Foot

For House

user_1184196827

&nbsp;进行了分件操作，优化接口和切口，组合度更加紧密

Batman Helmet蝙蝠侠面具

Cosplay

Papalumpi

Hello&nbsp;I used the Spool Holder from the A1 for the A1 Mini. But on the side Wall.See the Pictures…&nbsp;Bolt Diameter max. 5mmIn my case i used Spax 5x50 for OSB.

A1 Spool Holder Wall Mount

My workspace

Leif3D

A sweet little bag / purse hanger for any desk or shelf. The base model supports a desk thickness of up to 40mm minus your printer tolerance. If you need something for an even thicker desk feel free to scale the x & y axis up.

Sitting Cat Desk Bag / Purse Hanger

for Jenn

Gabb.99

Modular Box of drawers 190 x 190 mm.  Among the printing profiles are available small, medium and large drawers, which can be placed in the order you prefer. You can also add other boxes that can be interlock using the joint pieces (check the GIF in the project images).  No screws or glue are required (the glue only if you prefer to have more security); It all works by interlocking.  The 180x180 mm version (for A1 mini) is not available at the moment, but I will upload it on request; If you are interested write me a message.Enjoy&nbsp;&nbsp;<blockquote>If you like my work and you want to support me to do better, you can buy me a coffe at the following links <a target="_blank" href="https://buymeacoffee.com/GSprint" rel="nofollow noopener">https://buymeacoffee.com/GSprint</a> <figure class="image image_resized image-style-side" style="width:24.6%;"><a href="https://buymeacoffee.com/GSprint" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000145266/design/2024-05-03_919abd867ee7b.png"></a></figure><a target="_blank" href="https://ko-fi.com/gsprint" rel="nofollow noopener">https://ko-fi.com/gsprint</a> <figure class="image image_resized image-style-side" style="width:24.7%;"><a href="https://ko-fi.com/gsprint" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000145266/design/2024-05-03_b32099ab1171f.png"></a></figure></blockquote>