Duijinn

HG_Design

Bambu Boeing 737Prepared to be able to print on a single table, preferably with ams.This was designed to be assembled and glued.I made the STL of the fully assembled model available if you want to make a support stand. If you have any problems or suggestions for improvements to this project, please leave them in the comments.In the photos you can find the corresponding mounting location for each specific STL.Thanks

Bambu Boeing 737

chad

cats

SPStudio

<h4>I update, revise and improve my design for my fixes very often. Please only use my Print Profile (Labelled as Designer or SPStudio) to ensure this fix is updated & work well. Profile with Non-Designer tags may be of poor functionality or non updated model.</h4>Click on Like if this model helped you in some way. It is very important and will help increase the exposure of this design to more people who might need it. Cheers!&nbsp;&nbsp;&nbsp;<blockquote>AnnouncementNew and Improved V2 Versions for the Ams Buffer Fix <a target="_blank" href="https://makerworld.com/en/models/101046" rel="nofollow noopener">Before Buffer</a> and <a target="_blank" href="https://makerworld.com/en/models/85989" rel="nofollow noopener">After Buffer</a> have just been released. Do check them out in my profile to see what are the improvement. Thank you for your continuous support.<figure class="image image_resized" style="width:33.04%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2023-12-21_db335e9276f41.jpg"></figure></blockquote><h2> </h2><h2>Introduction</h2>Failed to pull back filament error can be caused by multiple different variables & factors. This is a part of an series of Ams fixes that i have designed which can complement each other when used together. I do suggest you install all my fixes together for the 0ptimal effect to help your filament travel properly across the entire system which in turn can help improve, reduce or remove any potential Ams errors.&nbsp;I have grouped all fixes into their respective Collection for ease of searching what to install.&nbsp;V2 Collection are improvements done on the shortcoming of V1 Collection. Feel free to try V2 Collection and if it doesn't work properly then you can try the V1 Collection. You can easily find each of the Collection by clicking on the Collections tab on my profile.&nbsp;Unfortunately there isn't a single fix that can 100% work for everyone. What works for others, may not work for you but my fixes is definately a great place to start and have worked for majority of the users. My fixes are precisely measured then modelled. A Proper Fix would have the highest chance to reduce or solve the error.&nbsp;<figure class="image image_resized" style="width:81.05%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2024-01-09_cd9c426e40212.jpg"></figure>&nbsp;<h2>What is this?</h2>&nbsp;This fix can help you correct the angle of the Ptfe tube exiting the printer through the rubber passthrough and in turn reduce friction and helps with Failed To Pull Back Filament Error for Bambu printers with Ams or even if you are not using an Ams this can help you align the rear Ptfe in a proper angle and position.&nbsp;This if combined with the V2 Extruder Fix found here <a target="_blank" href="https://makerworld.com/en/models/103987#profileId-110973" rel="nofollow noopener">https://makerworld.com/en/models/103987 </a>can further help reduce the error.&nbsp;If you encounter an situation such as an Failed to pull back error popped up and if you were to disconnect the Ptfe tube from the coupler on the tp back of the printer, which the other end goes into the hub on the other end before you can press play on the screen, in which after this action, the filament is pulled back without problems then this can likely help you.<h2> </h2><h2>Pre-installation</h2>&nbsp;Step 1 : Check the Ptfe tube inside the machine, it should not have any sharp bend or any part of the tube being squashed or misshaped in anyway. It should be also of the Bambu Specification of I/D of 2.5mm, that should have came with the printer.&nbsp;Step 2 : Disconnect the Ptfe cable inside the printer enclosure. Measure and Cut the Ptfe tube, i am unsure how long is the original Ptfe that came with the machine but what we need here is Exactly 52.2cm + - 0.20mm Max.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2023-12-23_e6c43b22cb198.jpg"></figure>&nbsp;Step 3: Move the Ptfe restrictor piece to this position. Take special note of the orientation and and its position according to measurement on the ruler. Observe the blue clip. Please do not install it the opposite way. This is a Key part please ensure and double confirm.&nbsp;The rear of the restriction to be at 10.2Cm and the front of the restrictor to be at 11.1Cm&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2023-12-23_5cdb0cfa60519.jpg"></figure>&nbsp;<h2>Support Removal</h2><figure class="media"><div data-oembed-url="https://youtube.com/shorts/u2ddQjwnLMc?feature=share"><div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=u2ddQjwnLMc"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://www.youtube.com/embed/u2ddQjwnLMc" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2023-12-23_1a74b9c544e2f.jpg"></figure>&nbsp;<figure class="media"><div data-oembed-url="https://youtu.be/wg1Q7tGmUrM"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/wg1Q7tGmUrM" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;This is how it should look like if fitted correctly. There will be enough length at the exit for you to slot in a <a target="_blank" href="https://makerworld.com/en/models/67779" rel="nofollow noopener">The Smooth 4 Way Splitter</a> or the original Ptfe connector.&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2023-12-23_084880504272e.jpg"></figure>&nbsp;&nbsp;&nbsp;<h2>What Mod / Fixes / Enhancement do i offer?</h2>Please don't download the wrong one. Only those in the photos below is designed by me who painstakingly took a lot of time to measure carefully and design just to get it working. #SupportOriginal Love you guys for all the support so far!&nbsp;- <a target="_blank" href="https://makerworld.com/en/models/47982" rel="nofollow noopener">Ams FIX Failed To Retract Filament Error (a preventive measure and solve the bay 2 and 3 error and prevent bay 1 and 4 to have any possibility of having an error due to tension and friction)</a> (Updated design on the 2nd photo below, try 1 then if it doesn't works properly for you then install the other one.)&nbsp;<figure class="image image_resized" style="width:74.94%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2024-01-10_2e40f9b49d622.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/56906" rel="nofollow noopener">(BRAND NEW) Ams Filament Pull Back Fix V2 Upgraded - Completely New Design Upgrade For Ams Filament Pull Back ERROR! Precisely Measured</a>&nbsp;<figure class="image image_resized" style="width:75.86%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2024-01-10_9c729f1a3501a.webp"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/52782" rel="nofollow noopener">- Ams Buffer Fix For Failed To Pull Back Filament Error (reduce wear on the external Ptfe tube and allow the most smooth, least friction angle to go into the Ams buffer thus reducing the possibility of an error popping up)</a>&nbsp;<figure class="image image_resized" style="width:75.68%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2024-01-10_14c8811c47696.webp"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/101046" rel="nofollow noopener">- V2 Ams Buffer Fix For Failed To Pull Back Filament Error (reduce wear on the external Ptfe tube and allow the most smooth, least friction angle to go into the Ams buffer thus reducing the possibility of an error popping up)</a>&nbsp;<figure class="image image_resized" style="width:76.45%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2024-01-10_6194006084695.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/53037" rel="nofollow noopener">- Ams Fix - Stack the Ams on tp (Using a carefully measured holder to hold the Ptfe in a curved angle that will allow filament to go through with the least possible amount of friction when the Ams is stacked on tp of the printer)</a>&nbsp;<figure class="image image_resized" style="width:77.35%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2024-01-10_e6ff2df6c7873.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/58543" rel="nofollow noopener">- Ams Buffer Ptfe Right Guide Mount Fix will correct and maintain a nearly 100% straight line when the Ptfe tube exit the Ams buffer to move into the printer extruder.</a>&nbsp;<figure class="image image_resized" style="width:78.46%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2024-01-10_f95cf24ce5c9e.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/85989" rel="nofollow noopener">- V2 Ams Buffer Right Ptfe Guide Mount - The Fix For Failed To Pull Back Filament a newly improved fix designed to replaced the V1 This will correct and maintain a nearly 100% straight line when the Ptfe tube exit the Ams buffer to move into the printer extruder. ez Installation. No screws needed!</a>&nbsp;<figure class="image image_resized" style="width:79.5%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2024-01-10_6ddf689393292.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/63021" rel="nofollow noopener">- Extruder Ams Filament Pull Back Fix will correct and maintain a nearly 100% straight line to move the filament in and out of the extruder. This will also reducing wear on the Ptfe tube. Its design allow the filament to travel in the most smooth, least amount of friction and pressure for the proper angle to go into and exit the extruder thus greatly reducing the possibility of an Failed To Retract Filament error or similar errors from popping up.</a>&nbsp;<figure class="image image_resized" style="width:82.04%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2024-01-10_4c9e59fa5529e.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/103987" rel="nofollow noopener">- V2 Extruder Ams Filament Pull Back Fix will correct and maintain a nearly 100% straight line to move the filament in and out of the extruder. This will also reducing wear on the Ptfe tube. Its design allow the filament to travel in the most smooth, least amount of friction and pressure for the proper angle to go into and exit the extruder thus greatly reducing the possibility of an Failed To Retract Filament error or similar errors from popping up.</a>&nbsp;<figure class="image image_resized" style="width:81.99%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2024-01-10_69d2ccb8ac279.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/67779" rel="nofollow noopener">- The Smooth 4 Way Splitter. Look No Further. Combined with Ams Hub Lite together with this small attachment, you will have the Smooth 4 Way Splitter.</a>&nbsp;<figure class="image image_resized" style="width:83.64%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393383/2023-11-19_96f9eed020e9b.gif"></figure>&nbsp;

Failed To Pull Back Filament Fix - Rear Stabilizer

For Printer

Reckit

Apple watch charging stand with hidden cable management. There are two versions - One with radius edges, and one without.

Apple Watch Charging Stand

Dillan

Chris1974

EDIT:I made a new version of the Maple Seed that flies even better than the previous one. It is a lot thinner and lighter than the old one, giving it a lot more hang time. See launching tips in description!It really flies significantly better!!!EDIT END.&nbsp;Important: The Maple Seed is delicate just like a real one.Let the bed cool first and then take it off!!!&nbsp;This is a Maple Leaf Seed. Throw it up high in the air and it wil start spinning and float back down gently.&nbsp;Designed by nature itself.&nbsp;Best launching results:Option 1: Go outside and throw it up in the air as high as you can.Option 2: Sit on the floor and throw it up to the ceiling. It will start spinning on the way up and float down gently.Option 3: Open your hand and hold it flat wilth your handpalm facing up. Put the seed with the kernel on your hand and the blade sticking out a bit. Flick the blade with the indexfinger of your other hand to start the rotation and launch it off your hand.

Improved Flying Maple Helicopter Seed toy

joealarson

In 2016 I took a family tradition of a crafty little Christmas tree with Scripture themed ornaments each with a lesson about Jesus Christ and made a 3D printed version. While that version was okay, the tree was too fragile, and there was no good place to store the ornaments between seasons. This is an update to that project that addresses these problems.All files print without needing supports.Print 24 ornaments to cover all hooks. Or, design your own with loops to create your own tree!Note: If you scale everything down to 90% it'll all fit on a Mini and everything should print fine.

chad

cats

For Printer

Dillan

fun

Christmas gift