Fits H2D nozzles perfectly, easy to read off nozzle size, printed in PLA-CF 0.6 for a quick strong easy print. Holds into storage well and easy to lock in and remove. Thanks for sharing.

Amazing upgrade, has solved the small issue I had of the printer sometime issuing an error on the length or friction on the PTFE tube. Much better fit than the Bambu 4 in 1. Didn’t have to change and screws out, all fitted back into location and printed out perfectly in PETG with ABS for the top clip. Thanks for sharing your design and system! Top Notch!!

Perfect tube fit and cut for the upgraded 4 in 1 fit

Just used the box wall mount to hold my Renault EV charger pack. Good fits considering the design was not intended for this charger. Quick simple print for EV charging storage!

Amazing fit with type 2 charger connector, Strong build and design and looks great in ABS-GF! Thanks for sharing your design

Great print fits the Renault 5 EV perfectly! Used ABS GF for a nice clean black ‘Matt’ finish. Only small issue is in the UK the coin slots need to be wider to take a pound coin for supermarket trollies etc. I’ll have to see if I can adapt the design unless the original design sees this and can help? Thanks for sharing design.

Nice standard Grifinity box - slot for swatches are spot on not tight at all. Prints very well and look smart in Black Matte PLA!

perfect very quick print for housing my spare meter.

Good design. I used ABS GF for the black frame in my photos and PETG for the actual AMS HT shelf as well as the clips. works perfectly and fits perfectly. Feel I may still need the Bambi Makerworld model as well for holding spools totally open for complete free movement but this works well for keep the filament inside the dryer at all times. Did find that there was some sagging at the layers directly above the bridging areas as there are no supports in th design and there are some largish bridge areas, it works and is strong but I’ve not had this issue before on any other prints and put it no to lack of supports. I may try and print again with some PETG supports added to see if it does indeed solve these visual layer lines at bridge point.

Perfect fit for the smaller swatch card, very well designed storage box. Not printed lid only base for my needs.

Fit the set of Hex tools and ‘clips’ well on to HSW.

Simple printer and well designed with good HSW fitting which fits well. perfect size pot to hold plenty of pens and small tools which regular HSW holders struggle with.

Great simple quick print which works perfectly for the Swatches as intended and designed for - perfect fit!

Fits my needs perfectly! Used the smaller swatch so it’s taking up less space and material but still does what I need it to do, plus it fits in my AMS stand which was designed to take these swatches. Just need to produce labels now, but sizes of space are perfect.

Works great, printed these before going ahead and printing out a full bed of them.

Great print! the extra increased size works perfectly on the Bambu spools. After a test I went ahead and printed out over 200 to use permanently 4 on each of my spools so they are always ready to use. Printed in ASA so they can stay in place for AMS 2 pro and AMS-HT. Tried the original designer ones first but they kept falling out of spool in AMS, these don’t. Thanks for sharing.

Brillient Tool!! great print first time, all tool ends fit perfectly in box and onto the Super Libe bottle, well done and thanks for sharing your work.

Great design, great stand. Been a fun project to print out over a week or so. Looks perfect in PLA-CF Black and Grey.

Great label design for marking your AMS and filament switcher modula. Only small issue I had was with the fitting of the AMS labels; they are a tight fit and can cause side elements to pull away from cap with printed letter. Only a little but a small design adjustment maybe valuable to strengthen these. But as a non mechanical piece it’s not a big problem - PLEASE SEE MY ADDITIONAL COMMENT BELOW IN A REPLY AS THIS IS ACTUALLY A DESIGN FEATURE TO ALLOW THE SIDES TO CLIP OVER AND HAVE SOKE GIVE. .

Brilliently laid out design. Printed in ABS-GF Grey filament and Black PETG and design came out perfect. Designer has provided some excellent files which fit very well with easy to follow instructions. All fits perfectly and easy to build. First time I used Support material for ABS and it worked a treat. Highly recommend using it here as the support connects to the thread area so you need a clean break. Design looks like it’s been injection moulded !