DSL 55

lukeofhazzard

Because they simply cost an incredible amount - print them out! ;) The parts can all be easily put together with a bit of superglue - what goes where should be pretty obvious.. (or see “instructions” in the file descriptions).<ul><li>Tight Dimensions, so make sure your printer is accurate!</li></ul>For the rear cover you need four 4x2 mm magnets.The cover for the front clock hands is not tested.I used this cheap movement here: <a target="_blank" href="https://www.amazon.de/dp/B08PT1W4KV?psc=1&ref=ppx_yo2ov_dt_b_product_details" rel="nofollow noopener">Amazon</a> - I think any movement with these dimensions (56x56x15 mm) should fit.

German Mid-Century Mantel Clock - "Dugena"

Works

Xeraj

<ul><li>Voronoi easter Egg. It is an elegant decoration of a figure by way of decomposition of metric space determined by distances to a given discrete set of objects in space, for example a discrete set of points.</li><li>narrower version: https://makerworld.com/en/models/144642#profileId-157308</li></ul>

Easter Egg Voronoi Thicker

Easter

emmaginn

<h2>Coins Planter with Hidden Drip Tray</h2>The one in the photo was resized at 80%. I&#39;ve resized as low as 60% without any issues with the locking drip tray. Hope you like it! Hope you like it!&nbsp;Commercial Licensing: <a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Patreons</a> also have the opportunity to use commercial licenses for their own creative projects, adding versatility and potential income streams.&nbsp;If you like this, please be sure to check out my <a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Patreon</a> where I upload many of my designs exclusively for members. Hope you like them!&nbsp;<figure class="image image_resized" style="width: 57.27%"><a href="https://www.patreon.com/emmaginn" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000192297/design/2024-05-06_43c269eba0e6.jpg"></a></figure><a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Stacker Planter/Vase with Hidden Drip Tray</a>&nbsp;<figure class="image image_resized" style="width: 58.89%"><a href="https://www.patreon.com/emmaginn" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000192297/design/2024-05-02_c4986346dbaf9.jpg"></a></figure><a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Rivers Planter with Hidden Drip Tray</a> <figure class="image image_resized" style="width: 58.58%"><a href="https://www.patreon.com/emmaginn" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000192297/design/2024-05-02_ac819f1c0e73c.jpg"></a></figure><a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Slice Planter with Hidden Drip Tray</a> <figure class="image image_resized" style="width: 55.7%"><a href="https://www.patreon.com/emmaginn" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000192297/design/2024-05-02_351443b9c636b.jpg"></a></figure><a target="_blank" href="https://www.patreon.com/emmaginn" rel="nofollow noopener">Ripple Propagation Planter with Stand</a>

Coins Planter with Hidden Drip Tray

Plants

柴猫猫天下第一

Black and white cat 奶牛猫

Animal

HG_Design

Snowflake christmas setPerfect for hanging on the Christmas tree.

Snowflake christmas set

Christmas

nikola

<h3>Pixel Board</h3><figure class="image image_resized image-style-align-center" style="width:100%;"><img src="https://makerworld.bblmw.com/makerworld/draft/96773/2023-09-22_lon3dtlzddwb.jpg"></figure>&nbsp;Changes:&nbsp;2023-10-15: Fixed the case which had incosistent edge.&nbsp;___&nbsp;&nbsp;PixelBoard is, as the name implies, a board that you can put 3D printed small squares aka “pixels” in and use it as a decorative piece, the board is 24 pixels wide and 12 pixels tall. The compact overall design fits on pretty much every printer, including Prusa Mini. If you're wondering what kind of designs can be made with pixels and a board of this size, scroll down to the bottom for some design examples.I recently found a similar model to this, and I noticed it had a few design flaws - but due to its licensing which didn't allow any modifications (remixes), I couldn't make any improvements to it - so I made an entirely new project from scratch over the weekend, and you can remix, share, and adapt it in any way you want - STEP files are included as well!&nbsp;Since it's literally designed over the weekend and not used over a longer period, if you have any improvement suggestions, feel free to make a remix or to comment.&nbsp;It's designed from the ground up for FDM printing, no supports, or anything similar required. It makes (optional, but recommended) use of 6x3mm magnets to hold the board firmly in the case, and the case itself doubles as a storage - and can hold more than 4 times the number of pixels required to fill the entire board, all in 4 different compartments, so you don't have to search through piles of different pixels to find the color you want.&nbsp;I have printed all the files on my X1C using generic 0.2mm settings with different filaments I had lying around, but please before you print everything at once, see below for print instructions and fit test models.&nbsp;<h3>Required materials:</h3>&nbsp;<ul><li>Optional: four 6x3mm magnets. These will hold the board extremely well in place, so much so that I had to design a push pin to push the board from the back, this is ideal since the box doubles as storage, and you don't want to have 1000+ pins accidentally drop on the floor.</li><li>3D Printer with at least 165mm bed size width - Prusa Mini can fit and print this.</li></ul><h4> </h4><h4> </h4><h4>Parts and print settings</h4><h4> </h4><h4>Board</h4><figure class="image image-style-align-center"><img src="https://makerworld.bblmw.com/makerworld/draft/96773/2023-09-22_79e71rpcqru4.jpg"></figure><h4> </h4>The board is printed using default settings of 0.2mm or lower, but there is no significant benefit of printing lower than 0.2. It requires no additional settings or anything else. Just make sure you're printing this with a dry filament to avoid any stringing which may lead to pixels not fitting quite well afterward.<h4>Pins</h4><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/96773/2023-09-22_fx9bx521pug5.jpg"></figure>&nbsp;The Pins are all 5x5mm for the cube part, as the tolerances for this are built into the board directly, but the diameter of the cylinder part may vary from printer to printer, and based on what kind of fit you want. I've included the pins with the cylinder at the following diameters: 5.00mm, 4.98mm, 4.96mm, 4.94mm, 4.92mm, and 4.90mm. They all have the size in their name Pin500 is Pin with a diameter of 5.00mm, Pin492 with diameter of 4.92mm, and so on.You need 288 pins to fill the whole board, I've included files with 298 pins to have some spare. If your printer bed adhesion isn't that reliable, I'd recommend printing in smaller batches instead of everything at once.&nbsp;You can print these in 0.2mm layer heights as well. No brim is required, and if you use it then it might be difficult to remove afterward.So, how do you know which pin size to print?&nbsp;<h4>Fit Test Files</h4><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/96773/2023-09-22_jjvpqn24uwh2.jpg"></figure>&nbsp;I've included a small 3x3 test board, print this, and all different pins and see which one fits best. If none of the pins fit, then you can, of course, use the scale feature of the slicer to adjust it, or modify the step files, but it means that your printer isn't quite accurate enough and this may lead to other issues as well. Use the same filament and same settings that you will use later on.For me personally, Pin498 fits the best.<h4>Case</h4><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/96773/2023-09-22_qendaq3orl0u.jpg"></figure>&nbsp;The case requires no supports and is designed to be printed this way. You can use any layer height that you want. 0.2 layer height produces nice results, and especially with some sanding, can be pretty. There are no major structural demands here, other than the magnets that are held in place. &nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/96773/2023-09-22_fwumhu5dey4w.png"></figure>Magnets/PushPin&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/96773/2023-09-22_7tw888ogds6s.jpg"></figure>If you decide to use magnets, you can put them in the side of the case, as well as the board, so they hold when the board is in place. There should be enough clearance to do a simple press fit for the magnets, bit if they keep falling out just add a drop of superglue.&nbsp;However, these magnets can be pretty strong, and getting the board out - when it's full of pins, can be very difficult, so I've designed a pin that goes from the front of the case to the back - make sure to put this in BEFORE you put the board in. The pins are pretty small, only 5 mm and barely noticeable, due to the small size, you'll need something to push them in from the back. If you don't want to deal with that, and you don't mind compromising on the design, there's also a long push pin version, this will stick out on the back 20mm and allow you to push it with your finger easily. Print both and try it out.The pins can be printed either way, and you don't need infill for them - 2 or 3 walls should do the trick.I printed mine in this orientation, so I get a smoother back-side finish. But this is up to you and how well your bed adhesion is. You can use brim on this to ensure it prints properly.<figure class="image image-style-align-center"><img src="https://makerworld.bblmw.com/makerworld/draft/96773/2023-09-22_wfahmznx9v0y.png"></figure>&nbsp;<h3>Assembly</h3>&nbsp;The assembly is pretty straightforward:&nbsp;<ul><li>Put the push pin in the case so you don't forget it.</li><li>Add magnets to the case and the board - make sure to orient them correctly</li><li>Done</li></ul>&nbsp;<h3>Design examples</h3>Besides the example image above, there are numerous designs that fit on a 24x12 board, here are some examples - and often you can even fit two of these on the board, or scale them down/up as you wish, as they don't use the entire space by themselves&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/96773/2023-09-22_kfdej6cryrvf.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/96773/2023-09-22_skdiiybul83w.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/96773/2023-09-22_pmm1qbz5sn0m.png"></figure>These screenshots come from <a target="_blank" href="https://www.brik.co/pages/gallery-search?q.size.height.min&q.size.height.max=12&q.size.width.max=24&q.size.width.min" rel="nofollow noopener">https://www.brik.co/pages/gallery-search?q.size.height.min&q.size.height.max=12&q.size.width.max=24&q.size.width.min</a>&nbsp;

Pixel Board

KIDS

dgemily

Geometric Horse wall art:&nbsp;Default size is around 200cmx180cm !168 pcs (all parts can be print at full size on a standard printer bed) All parts are numbered on the back and here you can find the numbers assignment : <a target="_blank" href="https://dgemily.com/Ext/3dprint/geometric-horse/geometric-horse_fullsize.pdf" rel="nofollow noopener">Geometric Horse wall art (pdf)</a>&nbsp;Organize pieces to the wall:<ul><li>use paper mask print pdf it with the same scale of your 3D print. cut all "triangles" (or only triangle's corners) tape it to the wall at the right level then place pieces to the wall. custom scale or custom paper format: you can generate the paper mask with the scale and the paper format that you want using adobe acrobat reader Dc ( free version) it lets you print in "poster" mode and select the paper format that you want.</li><li>use tool.stl the tool correspond to the exact space between pieces (except around jaw and one hoof) print it one or two times at the same scale of your model print, and use it like a "wedge" between pieces. (see the photos)</li><li>use projector print one or two page of the paper mask with the same scale of your print and tape it/them to the wall at the right level project the fullsize pdf, scale it and level it to the paper mask</li></ul>Fix pieces to the wall:<ul><li>use velcro tape</li><li>use double sided tape</li><li>use hot glue</li><li>use blu-tack ( you can also add small pieces of paper tape between wall and blu-tack to be sure to not have any traces to the wall) ...</li></ul>paper mask: (print on A4 pages without margin and resizing) you can use one page to place your first pieces to be sure to have it at the right level<ul><li>Full size <a target="_blank" href="https://dgemily.com/Ext/3dprint/geometric-horse/geometric-horse_muliA4-fullsize.pdf" rel="nofollow noopener">Geometric Horse wall art fullsize A4 (pdf)</a></li><li>Half size <a target="_blank" href="https://dgemily.com/Ext/3dprint/geometric-horse/geometric-horse_muliA4-halfsize.pdf" rel="nofollow noopener">Geometric Horse wall art halfsize A4 (pdf)</a></li><li>75% size <a target="_blank" href="https://dgemily.com/Ext/3dprint/geometric-horse/geometric-horse_muliA4-75percent.pdf" rel="nofollow noopener">Geometric Horse wall art 75% A4 (pdf)</a></li><li>Custom: use this <a target="_blank" href="https://dgemily.com/Ext/3dprint/geometric-horse/geometric-horse_fullsize.pdf" rel="nofollow noopener">Fullsize pdf file</a> adapt the dimension and paper format as you want</li></ul>tool.stl: you can print this tool.stl that should help you to place all parts together. the tool correspond to the exact space between pieces (except around jaw and one hoof)&nbsp;Follow me on <a target="_blank" href="https://www.instagram.com/dgemily_2.0/" rel="nofollow noopener">Instagram</a> to see more projects and works in progress

Geometric Horse wall art

Wall Art

SuperiorOrganiserSolutions

LED Light Box with Adidas Classic Trefoil Logo&nbsp;Design can be wall hung or sat on a surface, 5mm hole for power cable.&nbsp;Model has NOT been printed and tested but should be fine as its using my profile used on my other designs.&nbsp;LED Light Strip: <a target="_blank" href="https://amzn.to/3Sc05Ch" rel="nofollow noopener">https://amzn.to/3Sc05Ch</a>Dimmer Cables: <a target="_blank" href="https://amzn.to/3RC9xx4" rel="nofollow noopener">https://amzn.to/3RC9xx4</a>

Adidas Classic Trefoil LED Light Box Lamp

Lamp

Dahle1979

Mein selbst erstellter Gleitfuss für den Thermomix TM5 und TM6. Passt perfekt und Ihr könnt den Thermomix damit ganz einfach auf der Arbeitsplatte hin und her schieben. Damit geht Ihr auch nicht die Gefahr das die elektronische Waage des Thermomix kaputt geht oder Fehler anzeigt. Oft ist die Ursache nämlich das die Füsse des Thermomix kleben bleiben und beim abziehen dann kaputt gehen oder aufwendig neu eingesetzt bzw. kalibriert werden müssen.&nbsp;Ihr müsst 3 Stück für einen Thermomix Drucken!&nbsp;

Thermomix Gleitfuss TM5/TM6 Sliding Board Glides

Thermomix

DaTryhard22

Here is a highly detailed 1/10th scale model of a 28-inch tall traffic cone. The file is prepped for easy multicolor printing as the colored areas are segmented as separate faces.The included .3mf file is for Bambu Lab printers.Print with supports. Print slowly to ensure good layer adhesion for optimal strength. Based on: https://www.trafficsafetystore.com/shop/orange-28-inch-10-0-lb-black-base-cone-with-6-inch-4-inch-reflective-collars/CR28HDRC64