Cookiegory2

Roket_One

This is a re-upload of Jevus's Measuring Cubes (and photos) from Thingverse. I am not Jevus, but I like the design, a must have in a kitchen.If you find these useful and you want to tip the author, go to <a target="_blank" href="https://www.thingiverse.com/thing:2722562" rel="nofollow noopener">Jevus' Thingverse page</a>.I just want to ensure that this model is available in Makerworld, according to author license.&nbsp;There are six measurements per cube; one per side.Large Cube: 1 Cup, 2/3 Cup, 1/2 Cup, 1/3 Cup, 1/4 Cup, and 1/8 Cup.Small Cube: 1-1/2 Tbsp, 1 Tbsp, 1/2 Tbsp, 1 Tsp, 1/2 Tsp, and 1/4 TspThe small cube nests inside the larger one. Enjoy

Measuring Cubes - Cups, Tbsp

Father’s Day 

Hugo

If you need to secure your precious belongings in a safe place, you found what you were looking for. This safe is secured by a 3 digit combination to prevent anyone from opening it (unless they have a hammer or a heat gun, I mean it's just plastic at the end) This is kind of a long build but it is perfect to learn how a combination safe works. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_qic0h1icrn73.gif"></figure><h4>Printing instructions :</h4>Start by printing all the parts I provide, I used PLA with 0.2mm layer height and 20% infill for everything and non support.For some part the printing orientation is quite important for the strength, so this is the orientation for the parts you may have a doubt with :Both axle are printed on the side for better strength :<figure class="image image-style-align-center image_resized" style="width:49.05%;"><img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_9soz2jjbv724.jpg"></figure><figure class="image image-style-align-center image_resized" style="width:48.19%;"><img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_8l6i2qmusurb.jpg"></figure>The lever is printed like this :<figure class="image image-style-align-center image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_fpchn6fpzgzg.jpg"></figure>Both pivots are printed on the side :<figure class="image image-style-align-center image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_h3179x4t16fp.jpg"></figure>The pins are printed like this :<figure class="image image-style-align-center image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_d2hma44t28dw.jpg"></figure>The latch is printed like this :<figure class="image image-style-align-center image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_tpzanma84mk8.jpg"></figure>All the oher parts orientations should be pretty obvious.<h4>Building instructions :</h4><ol><li>Glue the dial with the disk_1 through the front_plate : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_pvatzay1ysnd.png"></li><li>Add the axle_1, the 2 remaining disks and the spacers, no glue required : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_er517y4une2y.png"></li><li>Glue the pins to each disk. On disk_1 and disk_3 the longer part should be facing towards the centre, and the centre pin is the biggest : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_k9t8edz0d0tj.png"> </li><li>Glue the knob to the axle_2 through the front plate, and then place the lever on the axle : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_8gvq2v99fauw.png"></li><li>Close the door assembly by gluing the back_plate to the front_plate : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_lp2gyrj08tic.png"></li><li>Place the latch over the lever's arm and secure it by gluing the 2 latch guides in their dedicated spot : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_vo0qe07t4477.png"> After this step, the assembly should look like this : <img src="https://media.printables.com/media/prints/259699/rich_content/bfb73901-7871-4b09-b254-c44da65f9763/image.png#%7B%22uuid%22%3A%2224948dac-c192-4727-8163-4e6776323946%22%2C%22w%22%3A1920%2C%22h%22%3A1440%7D"> At this point you can figure out the combination by following these steps : <ol><li>Turn the dial on the lock clockwise three times. This connects the 3 disks together, so they now turn with the dial.</li><li>Continue to turn the dial clockwise until the notch on the disk_3 is lined up with the lever. Stop and look at the dial to write down the first number of the combination.</li><li>Turn the dial counterclockwise for 1 full turn past the first number to engage the middle disk.</li><li>Continue to turn the dial counterclockwise until the notch from the middle disk lines up with the lever and stop to write down the second number of the combination.</li><li>Finally, turn the dial clockwise until the notch from the first disk lines up with the lever. All 3 notches should now be aligned. Write down the third number of the combination. You should now be able to turn the knob and unlock the mechanism.</li><li>Test your combination by unlocking the mechanism without looking at the disks. You can follow these instructions if you don't know how to : https://www.google.com/amp/s/www.wikihow.com/Open-a-Combination-Lock%3famp=1</li><li>Keep the numbers of the combination somewhere as it will never change. </li></ol></li><li>Glue the 2 pivots to the door assembly : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_3qdtt9kxxv8n.png"></li><li>To assemble the box start by placing the top and bottom walls on the pivots (no glue) : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_zbo1w07q7294.png"> </li><li>Glue the 2 side walls : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_9sjsq7gxjpmu.png"> When gluing the sides, do it with the door closed so you can see that everything is well centered. At this point you should test to lock and unlock the door a couple of times to test the combination before gluing the back_wall. </li><li>When you are sure of the combination you can glue the back_wall to finish the safe : <img src="https://makerworld.bblmw.com/makerworld/draft/606952/2024-02-29_rxxxpzkjo5kx.png"></li></ol>&nbsp;&nbsp;

Father’s Day

for later