Claimed4all

Brick

Downhill_Solutions

UPDATED V2 This upgrade contins:-better filament line routing (more straight / less clamping force)-optimized for AMS Riser-nicer look of BUS-cable routing-easyer print without supports&nbsp;"cable organiser for the backside of the P1S with AMS on the top.Should fit in P1P (upgraded thith glas top shield) / X1 / X1C.You have to change the casing screw on the left upper plate with a longer one which is include with the Bambu Lab Printer.Maybe you need to optimise the file for other filaments.The Pin is made to fit in the underside of the cable organiser to arrited in the 3mm hole in the printer casing."

Cable Organizer V2 (AMS Riser Option)

P1S Mods

SonicBoom

Ryobi Power Tool Holder left right with the option to have tool facing up or down

Ryobi Power Tool Holder 

Ryobi

kriswillcode

Have you ever wanted draw repeating geometric patterns at any time in any place?No? Well, let's pretend you did...This handheld print conveniently combines a drawing platform with a case for the gears and paper. It easily fits into a bag, pocket, or purse. As long as you have a pen, you're good to draw!The base is designed with multiple levels. The bottom level holds the paper, the drawing gears, and, if you can find one, a small pen. The next level provides a flat, secure drawing surface; you can even make art while walking! The top level has the stationary gear teeth and holds the paper in place.<h3>Paper and Pen</h3>This kit is designed to use Post-It Notes as paper. It requires no paper cutting, and your finished pieces of art are already self-adhesive!Almost any standard ballpoint pen can be used. A BIC pen was used for sizing, but the design works with every pen that I tested.<h3>Printing</h3><ul><li>Nozzle: 0.4 mm</li><li>Layer Height: 0.2 mm</li><li>Infill: at least 15% (20% or more recommended)</li><li>Vertical Shells: 3</li><li>Top/Bottom Layers: 5</li><li>Supports: No</li></ul>You'll need to print one top, middle, bottom, and latch. You can print as many gears as you want.I added a new version of the top with 31 teeth (Top-V2.stl). It's untested, but should create more complex patterns.For the middle layer, I suggest using 6 top/bottom layers and an infill of 25% at least. This will create a better drawing surface.The hinge is simply a length of 1.75mm filament. Make sure to cut one end to a steep angle.<h3>Assembly</h3><ol><li>Snap the latch into the holes on the front of the bottom.</li><li>Place the middle on top of the bottom. Be sure to pay attention to orientation: the square indent should be facing up.</li><li>Place the top on the middle. Be sure to line up the hinge.</li><li>Insert a straightened piece of 1.75mm filament into the side of the hinge. Rotate the filament as it's being forced in.</li><li>Trim the excess filament from the hinge.</li><li>Lift the top and middle parts. Place gears and Post-Its paper into the bottom.</li></ol><h3>Tips</h3>If the surface texture of the middle part is creating a texture in the drawing:<ul><li>Reprint the part with "ironing" enabled</li><li>Use an extra Post-It note or two</li></ul>For the hinge assembly:<ul><li>The hinge is meant to be stiff. It can hold the case open.</li><li>You can lightly sand down the filament if it's too stiff.</li><li>Rotating the filament as it's inserted helps.</li><li>Cutting the end of the filament to a sharp angle helps too.</li><li>Make sure the case stays closed while inserting the filament.</li></ul>Make sure the entire case is snapped closed before drawing!

Portable Hypocycloid Drawing Kit

Prints to make

ThreeD-Michael

Version 2 of my popular <a target="_blank" href="https://makerworld.com/en/models/62953" rel="nofollow noopener">Steam Train Whistle Set</a>. This whistles have only 2 tubes. However, the choosen geometry generates suitable overtones that ensure the realistic sound. The whistle can be blown softly or loudly. There are 3 versions (low, medium and high pitch).&nbsp;The new version has been optimized for 3D printing. Due to the changed geometry and alignment on the print bed, long bridges no longer need to be printed. A small drawback is the narrow contact surface, which - depending on the filament and print bed used - may require the use of a brim.&nbsp;Important:Print the whistles in the specified orientation and not too fast!&nbsp;By the way:I have designed many whistles, you can find them in my <a target="_blank" href="https://makerworld.com/en/u/77030249/collections/87334" rel="nofollow noopener">Whistle Collection</a>.

Brick

P1S Mods

Ryobi

Prints to make

Train Set