Chefbrandoncurtiss

Terminatordeux

A very simple and fast to print ring.Scale it to fit your finger.Printed in 0.12 mm height 100% infillthe details are incredibles please share your prints i would love to see them

skull ring ultra detailled

Rings

Antee

This a short suppressor I did for my AAP-01 pistol replica. It has buffers inside to actually silence the gun a bit. &nbsp;Happy printing!

AIRSOFT SUPPRESSOR VIKING INSPIRED

Airsoft Juggernaut

LoboCNC

Most string winders make you move your hand in a circular motion (like cranking a bicycle pedal). This more ergonomic version has the handle axis tilted at 7 degrees which lets your wrist pivot rather than translate (like whisking an egg). It prints without supports and snaps together without any additional fasteners.There are two versions of the handle - one plain and one with an integrated bridge pin puller.<h3>Print Settings</h3>Printer Brand:MakerGearPrinter: <div>M2</div>Rafts:NoSupports: <div>No</div>Resolution:0.2mmInfill: <div>20%</div>Notes:You electric guitar players will probably prefer the plain handle (winderhandle.stl), whereas you acoustic guitar players may prefer the handle with the bridge pin puller slot (winderhandle2.stl).Category: Music

Ergonomic String Winder

cool stuff

marcopiazzo95

The Rock Ocktopus with suckers<ul><li>0.20mm layer height;</li><li>3 walls;</li><li>3 bottom layer;</li><li>3 top layer;</li><li>Honeycomb infill density 20%</li></ul>

The Rocktopus with suckers

funny crap

TazzPB

Dipping my toes in to Hueforge, and made this awesome Pikachu V card! I had to use a little artistic license on the colours, but I think it came out pretty cool! Print details are below. This can be done with or without and AMS, just add a colour change at the layers listed below. Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmFilaments Used: PLA+ Sunlu Black Transmission Distance: 0.3 PLA+ Sunlu Red Transmission Distance: 6 PLA+ Sunlu Grey Transmission Distance: 2 PLA+ Sunlu Pure Yellow Transmission Distance: 5 PLA+ Sunlu White Transmission Distance: 5&nbsp;Swap Instructions: Start with Black At layer #13 (1.12mm) swap to Red At layer #15 (1.28mm) swap to Grey At layer #18 (1.52mm) swap to Pure Yellow At layer #23 (1.92mm) swap to White for the rest.

Hueforge Pikachu Card

brantlee

fireboy02

Perfect DND Dice tower for all types of board games. Supports the D20 dice as well as many other dice!&nbsp;No supports needed 2 wall lines15% supportive cubic infill

Castle Dice Tower

Kopp3D

A trophy for World's Best Mom and World's Best Dad - makes a great gift for your loved one. Each prints in two pieces and the top one is slotted into the base (holds sturdy!) Scalable and reversable. Bases are printed on the side to only have one color change per plate.

World's Best Mom / Dad Trophies (topper slots in - only one color change!)

3DPrintWell.co.uk

This is a spin off from an industrial instrument I made featuring a leaf spring click compliant mechanism.&nbsp;Best results with a 0.4mm nozzle at 0.2 layer height. Make sure you select supports on build plate only!

Green Lantern Fidget Ring

3BC 

DWdesigns

Experience the sensation and sounds of cocking the hammer and pulling the trigger with this simple fidget toy. It does not look like a gun. In fact, from one side the shape looks like a toy whale jumping out of water. &nbsp;I have made it as simple a design as I can think of. There are only 6 parts and assembly takes under one minute. The open design makes the trigger mechanism visible.&nbsp;Even though I designed this for the cocking and pulling actions, I have found myself fidgeting with it in the following additional ways, three of which do not make sounds.&nbsp;<ol><li>Pull the hammer down slightly but not enough into the cocked position, let the thumb slip and the hammer snap back up. Repeat. This action makes a crisp clicking sound. The feel of the spring and the crisp sounds are very pleasant and satisfying, and somewhat addictive :). A variation of this is to not let the thumb slip but hold onto the hammer as it moves back to feel the spring. This variation makes some noise.</li><li> Without the hammer in the cocked position, pull the trigger slightly and let the index finger slip and the trigger snap back into its natural position. Repeat. This action makes a crisp clicking sound. A variation of this action is to not let the index finger slip but hold onto the trigger as it moves back to feel the spring. This variation makes almost no noise.</li><li>Alternate between 1 and 2 above.</li><li>Roll the thumb on top of the trigger anchor pin, or the top of the hammer anchor pin, or alternating between the two. This action doesn’t make any sounds. If the top of the pins are not smooth enough, lightly sand or use a heat gun to smooth them out.</li><li>Push the hammer spring into the space between the hammer and the trigger, then flip it back out. This action makes noise.</li><li>Disassemble and reassemble the toy. Disassembly needs no tool and is easy to do, so it’s tempting to take it apart and put it back together, just for fun.</li><li>This last one is a bit tricky but I have done it when sitting in a chair with armrests: hang this toy upside down with the thumb holding the top of the spring anchor pin and the index finger or middle finger pressing on the opposite side of the handle, then swing it gently. It’s tricky because the index or middle finger has no easy spot to hold on to and the toy wants to drop down as it swings. I have not done it enough to the point that I can do it without paying attention.</li></ol>Easily print with PLA and PETG (the springs and the snap ring). No support, no brim. 100% 3D printed. Easy assembly (and disassembly). No tool is needed, no rubber bands, no screws, no glue. &nbsp;There are two versions, one for right-handed people and the other for left-handed people. Print profiles are provided for each. &nbsp;A fair warning though: The springs are 3D printed with plastic. So they will not last long but wear out and break after a certain amount of use. It comes with the territory of making something 100% 3D printed. Fortunately you have a 3D printer :). It’s recommended to print out some extra hammer springs for easy quick replacement. In any case, let me know what your experiences and thoughts are and I may consider modifying it next time to use steel springs.&nbsp;Instructions are provided for assembly, disassembly and use. Photos are extensively used in the step-by-step instructions for easy following.&nbsp;Choose your own favorite color combinations for different parts. However, at least one easily visible part should be printed using a bright color. If a wallet can be mistaken for a gun from a distance, this, too, can be.

Fidget Cock and Pull and More

dad wants

Maybe you just need to give the tall glass a quick rinse before using it for a different drink, or maybe you are like me who hand wash tall glasses, bottles, flasks and thermos because of the concern that the dishwashing machine will not do a good job of rinsing and simply replace drink residues with chemicals (dishwasher detergents). Before I had a printer and designed this, it took me quite some time to rinse thoroughly and it’s boring.&nbsp;This simple print will enable your kitchen sink side sprayer to perform double duty as a rinser for these tall drinkware. Easily flush away residues that are hard to get to. It also makes the boring task of cleaning/rinsing cool and fun. It can stay on and will not interfere with the side sprayer’s normal use.&nbsp;Two ways to use it: 1) as shown in GIF 1 and 2, hold and turn the side sprayer (which now becomes the rinser) up, place the glass on it, turn on the side sprayer, then turn the glass a few rounds to get a thorough rinse. There are grooves on it to make it easier and more secure to turn the glass; 2) as shown in GIF 3, hold and place the glass rinser onto the bottom of the sink, then press the glass on it and downwards to turn on the side sprayer (or turn it on by hand), turn the glass a few rounds to get a thorough rinse.&nbsp;Easily print with PETG. PLA may also work if not using hot water for extended period of time. No support is needed. Print profile is provided.&nbsp;Assembly is simple. See the two photos, which show different angles, for how it should be fit onto the head of the kitchen side sprayer.&nbsp;The hole of the model is 1.21 inch in diameter which fits into the head of the side sprayer in my kitchen sink. Scale up or down in the X- and Y- axis to fit yours if needed.&nbsp;Caution: The drinkware can be slippery so pay attention and keep hands steady when using the rinser so they won’t fall down. If the sprayer is turned on and the drinkware slips, the sprayer can also spray water onto the ceiling (it happened to me one time when I was distracted :)&nbsp;Check out my other kitchen Designs:&nbsp;<a target="_blank" href="https://makerworld.com/en/models/89422#profileId-96024" rel="nofollow noopener">Snap-on Hands-Free Can Strainer</a>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/96025#profileId-102401" rel="nofollow noopener">Fishing Frog Tea Bag Holder</a>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/101535#profileId-108314" rel="nofollow noopener">Yin Yang Tea Bag Organizer Tray</a>