CeDeROM

BamBam Design

<h3>Desk Cable Organizer - Simple efficient</h3>Easy printable Cable management clip for 3-12 cables!With mounting holes and/or double-sided tape mating.Fits up to Ø4,5 cable thickness.&nbsp;There are 2 profiles one with and one without mounting holes.Each profile has parts for 3x, 4x, 5x, 6x, 7x, 8x, 10x and 12x cables.&nbsp;Tip: The slot for double sided tape is 0,6mm deep, take 2 tapes if your tape is to thin.&nbsp;Happy Printing😁👍&nbsp;Commercial license you can get here:<a target="_blank" href="https://www.patreon.com/BamBamDesign/membership" rel="nofollow noopener">https://www.patreon.com/BamBamDesign/membership</a>

Desk Cable Organizer - Simple efficient

electric_utils

Krookr

You'll have to set the slicer to STOP THE PRINT at the top of magnets, before the first layer, that covers the magnets.In the presliced files I already added the stops to both heights. Remember to add the magnet and then continue the print.

Mario Piggy Bank with embedded magnets 

home_utils

jdireen

I originally came up with this design for my Sony NP-FW50 batteries but had a friend recently mention that they'd work great for 9v batteries too. The side dovetails let you securely combine a number of them together. There's a sloped back, counter to a retaining edge on the front top that keeps the batteries from unintentionally sliding out. The flat, side-by-side arrangement allows them to sit comfortably in a side pocket.In my experience, they work best printed in PETG.

9volt Battery Sleeve

electronics_util

Bean Eating Cookies

Christmas Penguin cookie cutter and stamp&nbsp;They are Cutters and stamps separate. Have a look at my profile for more cookie cutters and stamps! If you have a request don't hesitate to reach out!&nbsp;If you like what I am doing please consider buying me a coffee or tipping.<img src="https://cdn.buymeacoffee.com/buttons/bmc-new-btn-logo.svg?image_process=resize,w_800/format,webp?image_process=resize,w_800/format,webp"><a target="_blank" href="https://www.buymeacoffee.com/beaneatingcookies" rel="nofollow noopener">Buy me a coffee</a>

Christmas Penguin cookie cutter and stamp

food_forms

DGA3DP

Heart shaped phone stand with second version with Thank you sign. Material: PLA, PETG, ABS etc. Layer high: 0,3 or lower No support needed

Phone stand-Heart 

mobile_utils

luckyluc.64

I'm sure that is not the first out, or it's about time.Now, this is cheating. You should be able to reload with your finger faster than with that tool. Got that paper puncher? Me? I don't need more pain. And I have better to do with my finger… Like printing something cool.The objective is not to make another speed loader but to improve the ergonomics.&nbsp;But seriously, I did get some new mag, and to fill it up top was not fun. That brings the fun back to the plinking; there is no pain.&nbsp;As usual, I print it in ABS. PETg could do better, and PLA is for the guy waiting for the flash or holding the target.&nbsp;If you have a 1911 9mm, let me know if it works. It should, but I can't test it…It also should work with an impressive number of gun models and ammo. No big guy with your .50 or 410. Don't even try ;-) What .22? Really? Do you need a speed loader?Enjoy

1911 .45 ACP Single stack

sport_shooting

Kai-3D

Introducing a 3D printed Pac-Man ghost model that combines a pixel art charm with a touch of nostalgia. This playful creation faithfully captures the iconic ghost character's shape, making it a perfect collectible for fans of classic arcade gaming. While it offers the option for multicolor printing to mimic the vibrant in-game ghosts, its retro appeal shines even in monochrome. Relive the magic of vintage video games with this customizable and eye-catching Pac-Man ghost model. (Description could be generated by ChatGPT ;-) )

PacMan Ghost - Pixel / 8 Bit Design

videogames

eier1188

Cute Skull and crossbones earrings I made.&nbsp;These are meant to be combined with an earring hook and jump ring, a 6mm OD jump ring is necessary, a 5mm OD will work too, 4mmOD is very difficult but doable. Either way the jump rings may be difficult to attach, I didn't want to print a loop but that made the jump ring attachment more difficult. You will need needle nose pliers.&nbsp;Also to be used with a .2mm Nozzle, otherwise much of the detail is lost, but still doable with .4mm&nbsp;The print pauses twice to switch colors1st color is white, 2nd is black, 3rd is red&nbsp;UPDATE 1/12/24: If printing with a .4mm nozzle change the inner and outer walls to .25 and it should print that black outline pretty well, if not then you can mess with those settings, I've gone as far as .2 on all the line widths and been fine.&nbsp;These models take time and work to get right, I do this for fun and not business but if you want to support me or show gratitude and buy me a coffee I'd be Extremely grateful! <a target="_blank" href="https://www.buymeacoffee.com/eier" rel="nofollow noopener">https://www.buymeacoffee.com/eier</a>&nbsp;&nbsp;Let me know if you have any requests, Thank You!

Cute Skull Earings

jewellery

nikola

Continuity Camera mount for Dell P3421W, tested with iPhone 11 Pro Max and iPhone 12. Tilted a bit downwards so that Center stage isn't required to get a decent viewing angle as the monitor is pretty thick in the middle.It also includes a cable holder in case you want to keep a cable there to be able to easily access it and charge the phone while in use.I'd recommend printing it in PETG as it will be less brittle than PLA, but really any material should do. &nbsp;<h4>Custom sizes:</h4>If the model doesn't quite fit your iPhone, or your monitor, but the overall shape is good you can use “cut” feature in Prusa Slicer to cut the model and increase iPhone or monitor mount width like this:&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/546575766/draft/2023-09-22_v7i8oh21ovgv.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/user/546575766/draft/2023-09-22_rceiiij6l1qs.png"></figure>Both the part that goes on the monitor and the part that holds the iPhone has enough space to cut it cleanly. Then you can resize the middle part (green in the screenshot) to your desired size before moving the parts all together - for proper printing make sure all 3 parts are merged together (see screenshot part list on the right).Here's a step-by-step guide on how to do it:&nbsp;<figure class="image image-style-align-left image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/user/546575766/draft/2023-09-22_l0nimxmzgurq.png"></figure>Use the “Place on face” tool to put the flat part, the back of the iPhone holder, on the surface&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<figure class="image image-style-align-left image_resized" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/user/546575766/draft/2023-09-22_p5q7uuoi9nkg.png"></figure>Use the cut tool to cut the middle of the surface close to the bottom, but without it affecting any other walls or features other than the one highlighted.&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<figure class="image image_resized image-style-align-left" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/user/546575766/draft/2023-09-22_o3bv97zjkw8h.png"></figure>Perform the cut, and do the same thing again on the larger of the two pieces, this time cutting closer to the top like in the screenshot.&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<figure class="image image_resized image-style-align-left" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/user/546575766/draft/2023-09-22_27g0m7tm9btr.png"></figure>Once there are 3 pieces merge them all together so that they can be moved in the slicer.&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<figure class="image image_resized image-style-align-left" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/user/546575766/draft/2023-09-22_fa47bqlgu6al.png"></figure>Align the pieces. Since they're merged they can be moved without all of them needing to touch the print surface. You can copy the same coordinates for one axis or just move them around by hand until they all align.&nbsp;&nbsp;&nbsp;&nbsp;At this point you can either shrink, or even remove, the middle part, if your iPhone is too slim for the mount or increase its Z height if you need a bit more space. I'm just gonna show how to increase it, but I think by now the process for the opposite is also clear.&nbsp;<figure class="image image_resized image-style-align-left" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/user/546575766/draft/2023-09-22_3etlqcvh5ccz.png"></figure>Increase the height as much as you need.&nbsp;Use the tool “place on face” from the first step to put the part back in the correct &nbsp;&nbsp;<figure class="image image_resized image-style-align-left" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/user/546575766/draft/2023-09-22_df38i69ni6g8.png"></figure>Check your first layer! In case the parts aren't quite aligned you may not get a good first layer which may cause the print to fail. There is an easy fix for this though, just lower the print to actually go a bit below the print surface, since the print is same all the way through this doesn't cause any issues.&nbsp;&nbsp;&nbsp;<figure class="image image_resized image-style-align-left" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/user/546575766/draft/2023-09-22_qboouzx0d6y5.png"></figure>Done. All the parts are printed as one (because we merged them).&nbsp;Hint: If you're unsure about the dimensions, print just a few mm and try it out, you don't need to print the whole thing&nbsp;&nbsp;&nbsp;&nbsp;Same principle as above can be applied to the part that goes on the monitor itself, it's the same procedure.

Continuity Camera mount for Dell P3421W

comp_utils

AppHero

<div><h1>Summary</h1><div> For Pegboard 25mm Hole Spacing </div></div>

Knipex Pliers, Knipex Cobra Holder for Pegboard

workshop

Printsmiths

Phone stand or AirPods Pro case? Yes. Easily and conveniently prop your phone in portrait or landscape, and securely protect and carry your Apple AirPods Pro. The Stand Case Pro is also wireless charging compatible.

Stand Case Pro

mobile

3DMARKED

I use mostly fiberlogy refills and I wanted to be able to use them in my AMS, so I created this adaptor for the Bambulab refill spools&nbsp;This is my Paypal if you want to support my work and thanks in advance for that<a href="https://paypal.me/3DMARKED" rel="nofollow">https://paypal.me/3DMARKED</a>

Fiberlogy Refill Adaptor To Bambulab Spool

3Dutils

Amao Chan

A hungry polar bear fails to reach the fish held in the naughty seal’s mouth. Everytime the polar bear tries to catch the fish, the seal will sink back into the water and tease the poor, hungry polar bear.&nbsp;In fact, polar bears are indeed always famished because of the worsening condition of the planet due to global warming, and the North Arctic has become warmer than usual. On top of this, the melting of the ice has shrunk the polar bears’ living area, and made it difficult for them to hunt. There are many signs telling us that polar bears and the polar ice caps are slowly disappearing.&nbsp;The design, Polar Bear with Seal, was a paper DIY for the magazine Young Scientist. I really liked the concept, so I redesigned it into STL files. I hope this piece of art can convey a sense of beauty both in motion and stillness. While I was designing this, I put a lot of effort into observing the subtle changes in the movements of polar bears. In order to make this design work via 3d printing, I adjusted every component’s angle. Very few parts require supporting material.&nbsp;Ultimately, this art piece took me the longest time to design, and it’s the most complex one I have ever shared. I am extremely happy with the outcome!&nbsp;<a target="_blank" href="https://youtu.be/2ga2XGnS2OA" rel="nofollow noopener">https://youtu.be/2ga2XGnS2OA</a> <a target="_blank" href="https://youtu.be/UWyBoHDMF1g" rel="nofollow noopener">https://youtu.be/UWyBoHDMF1g</a>&nbsp;Thanks to SpiderMaker for sponsoring the creation of this work.<a target="_blank" href="https://www.amazon.com/SPIDER-MAKER-Matte-Printer-Filament/dp/B07HX9DY9F" rel="nofollow noopener">https://www.amazon.com/SPIDER-MAKER-Matte-Printer-Filament/dp/B07HX9DY9F</a>&nbsp;Material used SpiderMaker PLA Matte Paper White/Matte Iron blue/Matte Steel Blue/Matte Orchid Purple/Matte Peacock Green/Matte Coal Black&nbsp;Print suggestions 1.Layer height 0.2mm 2.Low down the flow to 90%or 95%. 3.Add oil on moveable parts&nbsp;<a target="_blank" href="https://amaochan.work/" rel="nofollow noopener">https://amaochan.work/</a> <a target="_blank" href="https://www.facebook.com/paperworkers/" rel="nofollow noopener">https://www.facebook.com/paperworkers/</a>&nbsp;北極熊與海豹調皮小海豹從浮冰的縫隙中探出頭來，用嘴中叼的魚逗弄著北極熊；當飢餓的北極熊揮掌搶魚時，海豹總是快一步的把頭縮回海面下，看樣子吃不到魚的北極熊要餓肚子了。 事實上，北極熊真的是處於挨餓狀態中！全球暖化，北極氣溫不斷上升，造成北極的海洋冰層融化，使得北極熊的活動範圍縮小、食物變少、獵食變得困難，許多跡像顯示北極熊正和北極海冰同時消失中！&nbsp;《北極熊與海豹》這個作品，原本是我為《科學少年》雜誌所設計紙製DIY作品；我很喜歡這個有趣的構想，所以把它重新設計為stl的版本。我希望這個作品在動與靜都能呈現美感，所以在設計時，特別注意北極熊在姿態上的微妙變化。為了配合3d列印工具的特性，調整了每個零件的角度；只有很少數的零件，在列印時需要設定支撐。《北極熊與海豹》是我目前分享的作品中，耗費時間最多、設計難度最高，但最後的設計成果，我很滿意！&nbsp;感謝 SpiderMaker 織造者 贊助本作品之創作&nbsp;使用材料 SpiderMaker PLA 消光白色、消光鐵灰藍色、消光鋼青色、消光蘭紫色、消光暗綠色、消光黑&nbsp;製作建議 1.層高0.2mm 2.流量降到90-95 3.組裝完成後在移動零件加些潤滑油。

Polar Bear with Seal (automata)

toys

N3RD solutions

Yet another low poly dog….but this time a Frenchie :)

Frenchie Low Poly Statue

animals

<div><h1>Summary</h1><div>Pangolins now are facing critical crisis as they are closing to extinct. In fact, humans are the murderers of this disaster, superstition and greed are the main reason to cause this massacre. Pangolins, the mammals covered in tough and overlapping scales, are actually far from aggressive. Their scales provide good defense against predators in wild. However, they’re considered the world’s most hunted animal because people believe that the meat is prized for medicinal ingredient and the scales help curl impotence. Nowadays, the numbers of pangolins are less and less, some people eat them only for the reason of showing their ostentatious wealth, what they do to these helpless animals is to make them approach to endangered. Although International trade in pangolins has been banned by CITES since 2000; and are listed them as 'protected species' in most Asian home states, scaly anteaters are still threaten with smuggling and poaching. Pangolins’ disappear would not be the result we expect to see, only when strictly implement of law enforcement on punishing these poachers and pangolin-eaters would effectively bring down the crisis of extinction. This is our latest chance to save pangolins, and please never make science predictions come true. Pangolin is a really skillful and difficult work that I have spent a lot of time on it. It has been passed at least six editions before presenting to all of you. What I was trying to challenge is an artwork with both perfect appearance and function. It was a little struggle for me to share this work at the beginning since I’ve fallen in love with it when it’s first done and stood in front of me. At this moment, what I am wondering more is to let you firsthand it, holding and feeling the variation with actions. Enjoy and I believe you’ll like it. Same file will be uploaded to <a href="http://fastlab.tw/" rel="nofollow">http://fastlab.tw/</a>, (Institute for Information Industry, III), which is a 3D works sharing website, welcome all 3D players upload your works and have fun here! Special thanks to Shinkong Synthetic Fibers Corp. for providing dedicated color materials (ABS) and supporting on this creation.Design Software - SketchUp my settings ABS z resolution 0.2mm scale 100% Don't printing all models are small then 75% of original model size, and set up 0.15mm layer resolution.<a href="https://amaochan.work/" rel="nofollow">https://amaochan.work/</a> <a href="https://www.facebook.com/paperworkers" rel="nofollow">https://www.facebook.com/paperworkers</a> <a href="https://www.youtube.com/watch?v=fkWxOLbFxPI" rel="nofollow">https://www.youtube.com/watch?v=fkWxOLbFxPI</a><hr>穿山甲正面臨迫切的危機，牠們走在快速滅絕道路上，人類是這場災難的兇手，迷信與貪婪是屠殺的原因。穿山甲這個性情溫和的動物，全身佈滿鱗片，這些鱗片在野外對於保護自己有些幫助，但是身上的鱗片也是牠們被獵殺的因素。因迷信穿山甲的鱗片有醫療與壯陽的效用，導致穿山甲這無辜的動物被瘋狂獵殺。也因為野外的穿山甲越來越少，所以穿山甲成了昂貴的食物，有些人僅僅是為了炫富而食用穿山甲，這樣的行為也把穿山甲推上最後的滅絕之路。雖然現在穿山甲在多個國家及地區均禁止出口及貿易，但是走私與盜獵依然存在！落實執法，逮捕並懲處這些盜獵者及食用者才能真正解決穿山甲的危機。科學家認為亞洲的穿山甲可能將於20年內滅絕！這不是我們想要的結果，現在就是解救穿山甲的最後機會。請別讓科學家的預言成真。這個作品我花了很多的時間，是一個難度很高的作品，自開始到完成創作至少修改了6個版本，不停地推翻與重建，因為我在挑戰一個美與機能都要兼具的作品。所以當我完成這個作品時，也同時愛上這個作品，因此有些捨不得分享出來。但我更期望朋友們也能夠親自體驗我的感受，能將牠握在手中，感覺牠的觸感、聲音與各種動態的變化。當你下載了並列印這作品時，願你也能像我一樣愛上這個作品。同樣的檔案我也分享於 <a href="http://fastlab.tw/" rel="nofollow">http://fastlab.tw/</a> 這是台灣資訊策進會的3D分享網頁，希望各位3D玩家也能慢慢豐富這個地方。感謝 新光合成纖維股份公司 訂製專用顏色之3D列印材料贊助本作品創作。列印建議 層高0.2mm 免支撐 縮小列印時請別小於0.75並提提高解析度到0.15mm</div><h1>Custom Section</h1><div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=fkWxOLbFxPI"><iframe src="//www.youtube.com/embed/fkWxOLbFxPI" frameborder="0" allowfullscreen="allowfullscreen"></iframe></div></div>

Save pangolins

nature

user_3257010834

Xiaomi Mi Temperature And Humidity Monitor 2 Stander