Cody

_donkey-brains_

One mace to rule them all?&nbsp;While there are a few adaptations of Sauron&#39;s mace scattered around the internet, I didn&#39;t necessary feel those were complete (no patterning), nor were they optimized well enough for printing and assembly (required internal structuring; a lot of post-processing). Therefore, I set out to model my own version from scratch that satisfied my own desired for a show piece. What I have here is a model designed entirely my me in fusion. I hope you enjoy it.&nbsp;This model consists of 21 pieces and 8 connectors to create a model that is ~46 inches long and can weigh upwards of 2kg. &nbsp;Printing Tips<ol><li>For my own print, I went with a silk filament because I hate post processing. While some parts can probably be printed flat, I have designed them to all be printed vertically. If using silk pla, I highly suggest to print all parts in the same orientation as that will give the best looking outcome. </li><li>I only own a P1S and have optimized this to print using most of the vertical space of that sized printer. If you have a smaller printer, I do apologize, but there are likely some spots where you can use the slicer to make parts smaller.</li><li>Any support I used were slim tree supports. I have uploaded my print profiles that I used which include manual tree supports. Threads, pattering, and small overhangs (like the handle rings) should not require any support. </li><li>I highly suggest to print the longer thread of the Lower Handle (Upper) piece facing up. This piece will be a weak point as it connects the lower handle to the rest of the mace. If that thread is printed down it will be supported and will be a weaker junction. I also suggest to use multiple bottom and top layers so this piece is strong.</li><li>Because the blades are optimized to be printed vertically, they have the pegs that will require support. Be sure to clean these supports well as the pegs being too large may effect final fitment. </li><li>Silk filament can give weird banding when cooling rate are different, so, if using silk filament, it may be a good idea to print each piece separately. This is what I did to ensure good consistency in the finish.</li><li>This print can probably use anywhere from 1kg all the way to 2kg of filament. Regardless, I highly suggest to make the lower handle sections either much more robust than the upper or, ideally, fully walled. My print profiles would culminate in a mace that weights about 1.7kg. </li></ol>Assembly Tips<ol><li>Assembly should be rather straight forward. I have attached pictures of the fusion model exploded into sections so as to be able to follow how to assemble. I suggest to assemble from the bottom to the top. I also suggest doing each section as a dry fitment before gluing everything together. After gluing any section, I suggest letting it cure for 24 hours before gluing attaching sections. </li><li>The threading has been given an ample offset, so these pieces should thread together easily. Thread each of the them together in the correct order dry and them take them apart and add a few drops of CA glue to the threads. Let these cure overnight. </li><li>For the upper handle section, Use the connector and CA glue to put the lower and upper sections together. Let cure 24 hours. </li><li>After both the lower and upper handle sections have cured, screw the lower handle section into the upper handle section. Use CA glue to bind these permanently. This will be a weakest point on the mace, so be careful. </li><li>Connect the upper and lower pike pieces using the large connector and CA glue. Let these cure 24 hours.</li><li>Using the smaller connector, connect the handle to the pike section. Fit this up with CA glue and let cure.</li><li>Dry fit each of the upper and lower blade sections into their respective positions in the pike. If these don&#39;t go in with no more than a little effort, ensure all support material has been removed. For blade assembly what worked best for me was:<ol><li>Add few drops of CA glue into each of the pike holes</li><li>Glue the blade connector into the bottom blade</li><li>Add glue to the top of the connector and place the top blade onto the lower blade and connector (this should give a few seconds to pull them apart when placing them into the pike holes). </li><li>Place the lower blade partway in to its pike hole</li><li>Place the upper blade partway into its pike hole</li><li>Press both the lower and upper blades all the way into their holes--this may require some wiggling and effort</li><li>Hold the upper and lower sections together vertically while pressing the entire thing toward the pike. Hold this for several seconds until glue sets. Then let cure fully before moving on to the next blade.</li></ol></li></ol>&nbsp;&nbsp;

Sauron's Mace

Props

Leif3D

A lovely black &amp; white bookmark with a nature scenery.&nbsp;The size is 150x50mm with a 4mm hole for a cord of your choice. The thickness is about 2.2mm&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm&nbsp;Filaments Used: PLA Sunlu Meta Black Transmission Distance: 1 PLA Sunlu Meta Grey Transmission Distance: 3.5 PLA+ Sunlu White Transmission Distance: 5&nbsp;Swap Instructions: Start with Black At layer #12 (1.04mm) swap to Grey At layer #20 (1.68mm) swap to White for the rest.&nbsp;If you like it you also might want to check out my <a target="_blank" href="https://makerworld.com/en/@Leif3D/collections/1135672" rel="nofollow noopener">other bookmarks</a>. I&#39;ve created a whole collection to cover different genre types. All using the same 3 filament colors to keep the printing costs low.&nbsp;<figure class="image image_resized" style="width:81.99%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000190534/design/2024-02-17_2af2f296a36f5.jpg"></figure>

Nature Bookmark (HueForge)

Bookmarks

dohara1985

<h3>Flower Earrings</h3> No AMS Needed Just color swap at layer.&nbsp;Can be made into a pendant and/ or Keychain by scaling up.&nbsp;Check out my large selection of earrings.&nbsp;<h3>Colors used</h3>Pink - <a target="_blank" href="https://amzn.to/3TjRX2R" rel="nofollow noopener">Elegoo PLA Matte Sakura Pink</a>White - <a target="_blank" href="https://amzn.to/3IbazvE" rel="nofollow noopener">Elegoo PLA white</a>Black -<a target="_blank" href="https://amzn.to/48sJe2J" rel="nofollow noopener"> Elegoo Rapid Black Pla Plus</a>Yellow - Bambu Basic Yellow&nbsp;<h3>Parts</h3>Below are links to Items I use for my Earrings.<a target="_blank" href="https://amzn.to/3UYahjk" rel="nofollow noopener">Bigger Pack</a><a target="_blank" href="https://amzn.to/3J14lim" rel="nofollow noopener">Earring Cards</a>&nbsp;<h3>STLs</h3>In Bambu Studio load all STL&#39;s at one time. It will ask “Load these files as a single object with multiple parts?”. Click yes. Than right click on each object and click the color for that object.Or pause at the desired layer height to change colors.&nbsp;<h3>Bambu Studio Files</h3>Included is the studio print profile file.These files are designed to be used with an AMS.&nbsp;&nbsp;<h3>Please &#34;Like&#34;, review, follow and upload make.</h3>&nbsp;<h3>Commercial license</h3>As of 2/25/24 my designs are no longer allowed to be sold commercially.Do you want to sell prints of this model or any of my models? You can purchase commercial licensing at <a target="_blank" href="http://www.patreon.com/ErraticallyEccentricCreations" rel="nofollow noopener">Patreon</a> or Buy Me A <a target="_blank" href="https://www.buymeacoffee.com/dohara1985o" rel="nofollow noopener">Coffee</a>.&nbsp;Earring Commercial License is just $3 a month. A full commercial license for all of my designs is just $7 a month.

Flower Earrings

Keychains

Criticalprint3d

A book that you can use to store your dice, Halloween candy or other stuff. Blank cover without the skull included. Can store approximately six sets of polyhedral dice. See my recommended print settings below!  Height: 175mm / 7&#34; Width: 125mm / 5&#34; Thickness: 37mm (internal 30mm) / 1.5&#34; (internal 1.2&#34;)&nbsp;I can adjust the size on request.Best regards, Jonas COVER: No supports needed 0.2mm layer height 2 walls 10% infillTo get a leathery look on the cover: Enable Fuzzy skinFuzzy skin Point Distance 0.4mm Fuzzy skin Thickness 0.1mm (max)(Fuzzy settings are the same in most slicers but results may vary with printer model and outer wall print speed. Slower is better)  PAGES: No supports needed 0.24mm layer height 3 Walls 10% infill

Skull Book storage - Snap close, no magnets needed

Dice holders

TripleGWorkshop

Recommended order:Black, Dk Brown, Lt Brown, Grey, White or Black, Dark red, Orange, Grey, White.Quick Guide to changing filament~<ol><li>Have some paper to push away extruded filament. That's why I always set up the models on the left. </li><li>When the MK3 jogs after a change it will spit out another inch, so I follow it with paper until it starts to move back down. Doing this has given great, repeatable results.</li><li>Use a tool like this to help changes→ <a href="https://www.printables.com/model/329171-filament-change-tool" rel="nofollow">https://www.printables.com/model/329171-filament-change-tool</a></li><li>Have fun!</li></ol>This is a PrusaSlicer screenshot.<figure class="image image_resized" style="width:100%;"><img src="https://makerworld.bblmw.com/makerworld/draft/120142/2023-10-26_9poktr76i4fc.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/120142/2023-10-26_s2or5uv96sen.jpg"></figure>

Props

Bookmarks

Keychains

Dice holders

Flat Art