Boss Tech Print Innovations

SchulteGeileTechnik

Please keep in mind that they are under a NON COMMERCIAL license, so don't sell the files or prints using this design.  &nbsp;I designed three geometric plant pots for some succulents. In addition, I created an inside pot for each planter with some holes in their bottom and a little offset from the ground so that excess water can escape.They were designed to fit small succulents with an inside width of ~60 to ~65 mm. They are all around the same height (roughly 60mm from the ground).I would love to see your prints, so if you make one be sure to post a picture under makes. If you like my designs or have any questions leave a comment and maybe consider a little tip.I also added an STL file for the base. Mine is made of concrete and not 3d printed, but I modeled it anyway to find out how the planters would look on it. It is about 260 mm long so maybe you have to scale it down a little bit to make it fit on your print bed.&nbsp;You may also find some of my files on thingiverse and printables. I made my printables account to get away from thingiverse, but since I heard a lot of good things about MakerWorld, I decided to upload on here as well. I have access to a P1P at work and a friend of mine owns an A1, so I may be able to add some Bambuslicer-specific files in the future as well.

Modern geometric succulent plant pot 

Gifts

Ross3D

This is a medium-sized stationery / tool holder with the design of Bambu Lab's P1S tool head.I took some liberties in slightly flattening the toolhead to maximize the available space for storing stationery or tools.&nbsp;Included in the model files are complete unit, as well as split unit for those who want to reduce waste. They can be attached with superglue.&nbsp;Update 03 Feb 2024:I've also made the A1 Toolhead variant: https://makerworld.com/en/models/169124

Bambu Lab Toolhead Stationery Holder / Pen Holder / Pencil Holder / Tool Holder

Storage Containers 

omegapoint

Simple holiday gift tags, only 1 mm thick. If you don't have an ams, don't paint the model. Simply change filaments at the start of layer 4. There is already a pause at this height. If you have ams, you can remove the pause, and paint and print as you wish. Don't recommend scaling z, especially if you intend to do manual filament changes. Scaling x and y should be fine.

Minimalist Christmas Holiday Gift Tags Multi-Color

Christmas 

Zhanchi Wang

24mm x 24mm filament sample

Swatch Sample

Swatch Samples

LP PRINT

general washers M2 to M10 measure

general washers  M2 to M10 measure 

Tools

Nakozen

The Imperial AT-ST “Chicken Walker” scouts ahead on the lush moon of Endor, seeking out any potentially rebellious individuals attempting to halt the Emperor's efforts. Fast moving and nimble for its size, and still extremely deadly with a half-decent pilot, it is not something you would want to be caught out in the open with, Jedi or not. Ohhh god is that a teddy bea--aaaarrghkk---!! This is a kit I've been wanting to make properly for a few years now, and finally sat down to give it a real attempt. I hope I have done it justice!-----------------------------------------------Some parts are super small, so some care is required. Additionally the kit should scale up just fine, although untested as of yet!On folding the main body panels, it is okay if one or two panels sheer off, it will still stick together, but if 3 or 4 fail, a little glue may be required for the roof piece! (If this is a big enough issue I may add another connection, I just wanted to preserve the top detailing.)Included is just the regular fit for the time being, try setting outer walls to print first.You can make it EVEN TIGHTER by increasing the Z-scale by 15%. For those uninterested in the card format, there is a frameless variant included! ------------------------------------------------------------Print at 0.2mm layer height, there really is no benefit from printing at a higher resolution and it could affect the fit. Be sure to print with 100% infill for it to hang straight as the weight distribution can be sensitive ------------------------------------------------------------My other Star Wars themed kits:X-WING - <a target="_blank" href="https://www.printables.com/model/143177-x-wing-kit-card-redux" rel="nofollow noopener">https://www.printables.com/model/143177-x-wing-kit-card-redux</a> Y-WING - <a target="_blank" href="https://www.printables.com/model/289165-y-wing-kit-card-redux" rel="nofollow noopener">https://www.printables.com/model/289165-y-wing-kit-card-redux</a> B-WING - <a target="_blank" href="https://www.printables.com/model/143174-b-wing-kit-card" rel="nofollow noopener">https://www.printables.com/model/143174-b-wing-kit-card</a> TIE Advanced - <a target="_blank" href="https://www.printables.com/model/143178-tie-advanced-kit-card" rel="nofollow noopener">https://www.printables.com/model/143178-tie-advanced-kit-card</a> Valen-TIE/N - <a target="_blank" href="https://www.printables.com/model/393740-valen-tien-fighter-kit-card" rel="nofollow noopener">https://www.printables.com/model/393740-valen-tien-fighter-kit-card</a> Tauntaun - <a target="_blank" href="https://www.printables.com/model/143208-tauntaun-kit-card" rel="nofollow noopener">https://www.printables.com/model/143208-tauntaun-kit-card</a> V-19 Torrent - <a target="_blank" href="https://www.printables.com/model/143196-v-19-torrent-kit-card" rel="nofollow noopener">https://www.printables.com/model/143196-v-19-torrent-kit-card</a> Tri-Fighter - <a target="_blank" href="https://www.printables.com/model/143197-tri-fighter-mini-kit-card" rel="nofollow noopener">https://www.printables.com/model/143197-tri-fighter-mini-kit-card</a> Looking to try your hand at making your own Kit Card? Follow this simple guide to get a head-start! <a target="_blank" href="https://3dwithus.com/how-to-design-kit-card-models" rel="nofollow noopener">https://3dwithus.com/how-to-design-kit-card-models</a>------------------------------------------------------------<h3>Interested in selling?</h3>All files are marked as non-commercial along with any remixes created from them.If you are interested in selling physical prints of my models anywhere, be it online or offline, you can obtain a sales license when subscribed to Tier 3 of my Ko-Fi memberships! <a target="_blank" href="https://ko-fi.com/nakozen/tiers" rel="nofollow noopener">https://ko-fi.com/nakozen/tiers</a><h3>Want to show me you love me? Buy me a "coffee"...! <a target="_blank" href="https://ko-fi.com/nakozen" rel="nofollow noopener">https://ko-fi.com/nakozen</a></h3>

AT-ST Walker Kit Card

toys 

blecheimer

This is a spoon that allows fast and precise spooning. You can easily fill your smallest and largest desiccant containers without spilling the tiny pearls - say goodbye to funnels. The unscaled spoon can hold ~12ml that is 10g of silica-gel pearls.&nbsp;Update: Based on a comment of user fish_ I made a stand for this spoon: <a target="_blank" href="https://makerworld.com/de/models/28648#profileId-25036" rel="nofollow noopener">https://makerworld.com/de/models/28648#profileId-25036</a>&nbsp;Disclaimer: This work by blecheimer is licensed under <a target="_blank" href="http://creativecommons.org/licenses/by-nc-sa/4.0/?ref=chooser-v1" rel="nofollow noopener">CC BY-NC-SA 4.0</a> You are not allowed to copy this model to other 3D printing websites without my permission.

Spoon for Fast & Precise Spooning

Bambu Parts 🔧

CrazyCoolPrints3D

This is an X1C Desktop Organizer. It was made to organize anything you want. A structured insert is coming soon. This doesn’t need an AMS! It can be printed with layer changes for multi-color. A P1S / P1P version is on the way! This model can also be sized up. Patreon (For Commercial Licenses To Sell And More Models): <a target="_blank" href="https://www.patreon.com/user?u=80724611" rel="nofollow noopener">https://www.patreon.com/user?u=80724611</a> &nbsp;Step By Step Process:<ol><li>Print the parts (made to work with or without the AMS).</li><li>Slide the parts in the order shown in the assembly file (glue shouldn’t be needed).</li><li>Slide the insert in, multiple versions will be available but currently there is only an empty one.</li></ol>&nbsp;Different Versions:P1S Version: <a target="_blank" href="https://makerworld.com/en/models/14742#profileId-14556" rel="nofollow noopener">https://makerworld.com/en/models/14742#profileId-14556</a>P1P Version: <a target="_blank" href="https://makerworld.com/en/models/26072#profileId-22450" rel="nofollow noopener">https://makerworld.com/en/models/26072#profileId-22450</a>&nbsp;Update Log:(9/12/23): Released&nbsp;(Please report any issues to my discord: coaster fan#4551)