BlakeMajik

DWdesigns

Experience the sensation and sounds of cocking the hammer and pulling the trigger with this simple fidget toy. It does not look like a gun. In fact, from one side the shape looks like a toy whale jumping out of water. &nbsp;I have made it as simple a design as I can think of. There are only 6 parts and assembly takes under one minute. The open design makes the trigger mechanism visible.&nbsp;Even though I designed this for the cocking and pulling actions, I have found myself fidgeting with it in the following additional ways, three of which do not make sounds.&nbsp;<ol><li>Pull the hammer down slightly but not enough into the cocked position, let the thumb slip and the hammer snap back up. Repeat. This action makes a crisp clicking sound. The feel of the spring and the crisp sounds are very pleasant and satisfying, and somewhat addictive :). A variation of this is to not let the thumb slip but hold onto the hammer as it moves back to feel the spring. This variation makes some noise.</li><li> Without the hammer in the cocked position, pull the trigger slightly and let the index finger slip and the trigger snap back into its natural position. Repeat. This action makes a crisp clicking sound. A variation of this action is to not let the index finger slip but hold onto the trigger as it moves back to feel the spring. This variation makes almost no noise.</li><li>Alternate between 1 and 2 above.</li><li>Roll the thumb on top of the trigger anchor pin, or the top of the hammer anchor pin, or alternating between the two. This action doesn’t make any sounds. If the top of the pins are not smooth enough, lightly sand or use a heat gun to smooth them out.</li><li>Push the hammer spring into the space between the hammer and the trigger, then flip it back out. This action makes noise.</li><li>Disassemble and reassemble the toy. Disassembly needs no tool and is easy to do, so it’s tempting to take it apart and put it back together, just for fun.</li><li>This last one is a bit tricky but I have done it when sitting in a chair with armrests: hang this toy upside down with the thumb holding the top of the spring anchor pin and the index finger or middle finger pressing on the opposite side of the handle, then swing it gently. It’s tricky because the index or middle finger has no easy spot to hold on to and the toy wants to drop down as it swings. I have not done it enough to the point that I can do it without paying attention.</li></ol>Easily print with PLA and PETG (the springs and the snap ring). No support, no brim. 100% 3D printed. Easy assembly (and disassembly). No tool is needed, no rubber bands, no screws, no glue. &nbsp;There are two versions, one for right-handed people and the other for left-handed people. Print profiles are provided for each. &nbsp;A fair warning though: The springs are 3D printed with plastic. So they will not last long but wear out and break after a certain amount of use. It comes with the territory of making something 100% 3D printed. Fortunately you have a 3D printer :). It’s recommended to print out some extra hammer springs for easy quick replacement. In any case, let me know what your experiences and thoughts are and I may consider modifying it next time to use steel springs.&nbsp;Instructions are provided for assembly, disassembly and use. Photos are extensively used in the step-by-step instructions for easy following.&nbsp;Choose your own favorite color combinations for different parts. However, at least one easily visible part should be printed using a bright color. If a wallet can be mistaken for a gun from a distance, this, too, can be.

Fidget Cock and Pull and More

Fidget Toys

Valeria Momo

This is an expansion pack of the <a target="_blank" href="https://makerworld.com/en/models/441862#profileId-347713" rel="nofollow noopener">Ninja Cat Game</a>. UPGRADE UNLOCKED, the <a target="_blank" href="https://makerworld.com/en/models/444832#profileId-351126" rel="nofollow noopener">gaming dice</a>🎲 is available! Increase the difficulty level, you will have to choose the mice of the color of the <a target="_blank" href="https://makerworld.com/en/models/444832#profileId-351126" rel="nofollow noopener">dice</a>!<figure class="image image_resized" style="width:18.89%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000445322/design/2024-04-28_70f3f4841c4ac.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000445322/design/2023-11-19_c8d27404379f3.png"></figure>🐭 THE FURRY STACKING TOY IS HERE: Stack the 12 adorable King Fu mice in every configuration imaginable and watch as the tower grows taller before it tumbles down! Turn a dreary Sunday into a fun day with this delightful set of 3D printed blocks.&nbsp;🐭 UNLEASH YOUR RODENT SIDE: Our stacking toy features charming 3D printed mice with curly tails, feet, and hands where you can attempt to hang other mice, offering more avenues for imaginative play than traditional stacking cups or ring sets.&nbsp;🐭 PERFECT FOR KIDS, TEENS, ADULTS, AND BEYOND: Crafted to provide endless stacking entertainment for mouse enthusiasts of all ages, our mouse stacking toy is ideal for de-stressing at work, bonding with your children, or adding a playful touch to your home decor.&nbsp;🐭 SPOIL YOUR LOVED ONES ON ANY OCCASION: Whether you&#39;re seeking adorable gifts for family members, Christmas presents for friends, or unique birthday gifts for boys or girls, this vibrant playset is a wonderful gift idea for both adults and children.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000445322/design/2023-11-19_c8d27404379f3.png"></figure><h2>Commercial license</h2>Do you want to sell prints of my models? You can purchase commercial licensing <a target="_blank" href="https://patreon.com/ValeriaMomo?utm_medium=clipboard_copy&amp;utm_source=copyLink&amp;utm_campaign=creatorshare_creator&amp;utm_content=join_link" rel="nofollow noopener">by joining the Commercial License in my Patreon</a>.

Ninja Mice: Ninja Cats Expansion Pack

Toys

Hrbecek

Batman wallart

Karson’s Collection

Scott711

This is a print in place winding spool I designed for standard length soft measuring tapes (60" / 150 cm) having width up to ¾" / 20 mm. If you need a version for a 120"/300cm soft tape, you can find it <a target="_blank" href="https://makerworld.com/en/models/380358#profileId-280542" rel="nofollow noopener">here</a>.&nbsp;After removing from the print bed, use a little force to free the spool from some small support, and run the spool back and forth a few time to smooth it out. Putting a few drops of light oil in the top center hole will make it run even smoother. I've printed in both matte and basic PLA with good success.&nbsp;Do not use supports. You may get a floating regions warning from your slicer telling you to use supports or to reorient, but print the model bottom side down without supports. I also suggest using 0.2mm layer height if you choose not to print with the uploaded .3mf print profile.

Soft Tape Measure Spool - Print in Place

 Utility 

mcmaven

This Print Profile includes all the components you need to upgrade your AMS to use loose (silica gel) desiccant. And the additional Dry Pods allow the AMS to hold more desiccant, which will mean longer times between refreshes.&nbsp;This has been done before, in many different combinations, but I couldn&#39;t find one that met all my needs. I feel that this remix contains the best combination of AMS Dry Pod and Desiccant Containers that are currently available, and I added a Funnel to help load them with silica.  There are 3 parts included that can hold the hygrometer, only print one: 1) a Shallow Hole version with slots for the hygrometers with 30 degree tabs that can hold more desiccant, 2) a Shallow Hole version with slots for the hygrometers with vertical tabs that can hold more desiccant, and 3) a Thru Hole version with 30 degree slots for the hygrometer tabs, designed by FLAP_design, where the hole for the hygrometer goes all the way through the pod. This version holds desiccant in the Dry Pod, but it can generate a more accurate reading because it will be measuring the overall AMS humidity, rather than the humidity of the desiccant in the Dry Pod with the hygrometer, i.e., the readout is less likely to be be distorted by the silica close to the reader.&nbsp;Just drag your preferred option onto the build plate.  The Round Hygrometer can be found here: <a target="_blank" href="https://www.amazon.ca/Hygrometer-Thermometer-Humidifiers-Dehumidifiers-Greenhouse/dp/B07BLQMR97" rel="nofollow noopener">https://www.amazon.ca/Hygrometer-Thermometer-Humidifiers-Dehumidifiers-Greenhouse/dp/B07BLQMR97</a>&nbsp;The Desiccant Containers can be loaded with generic desiccant and dropped into the slots in the back of the AMS. The top of the Desiccant Containers is split into two parts. The lower part should be glued on, and the upper snapped in after desiccant is added. They are easy to remove and replace the desiccant in.&nbsp;I used this desiccant: <a target="_blank" href="https://www.amazon.com/gp/product/B07QRRHJV3" rel="nofollow noopener">https://www.amazon.com/gp/product/B07QRRHJV3</a>&nbsp;To refresh the desiccant; pour it into a glass tray, place in the microwave for 2 minutes. Let it cool, then pour it back into the Dry Boxes. DO NOT put the Dry Boxes in the microwave! The desiccant gets VERY hot and will melt the Dry Boxes.&nbsp;Note that the Dry Pods will also work with the Hydra spool tray.Or if you are using the factory Bambu AMS spool tray then after inserting the Desiccant Containers, the original AMS dessicant covers can be snapped on top of them.&nbsp;With fresh desiccant, the humidity was down to 10% after a couple of hours, and it has stayed there for over 2 months now.&nbsp;24/4/7Added Pod for round hygrometers with vertical tabs.&nbsp;24/06/13V3.3 version adds an extension to the Funnel that allows it to cover Wide Dry Pods so desiccant is not lost when filling them. The same Funnel works also with Narrow Dry Pods.&nbsp;

AMS Dry Pods Wide, Narrow, Hygro, Trays, & Funnel

Printer Parts

Iguanahotsauce

The perfect Valentine's day gift for the brick lover you know is this stackable heart shaped storage box.&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/makingwithmakers" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;I appreciate any support whether it's just a like an download or if you buy me a coffee (I drink a lot of coffee so anything helps haha)

Fidget Toys

Toys

Karson’s Collection

Utility

Printer Parts

stuff