BlaXXuN

EDDIEB3D_

Can be scaled up but not down..2 layer height required for best results&nbsp;

Superman String Art

martin.taichl

This is my model of the Atlantis as seen in Stargate Atlanis tv series. Model is over 60cm in diameter and approaches 3 kilos. It has already built in preparation for the LED lights so if you want to make the towers and stardrive lit, you do not need to tinker with the data at all. It is once again a kit so everything fits together like a lego and no glue is needed. For the easier assembly, please watch the following playlist where the assemble process is described in detail. <figure class="media"></figure>&nbsp;The model comes with a stand though in the end I decided to not use it and display it as it is. Hope you like it.

Atlantis From Stargate Atlantis

stargate

fowlkstravis

This trick present has a hidden latch mechanism that will keep it securely closed until you twist the topper on the lid.&nbsp;&nbsp;&nbsp;&nbsp;<h3>Printing</h3><h4>For a square boxes you will need</h4><ul><li>1 square_lid</li><li>1 square_base_[small/medium/large]</li><li>1 square_spring</li><li>2 square_latch</li><li>4 square_base_[small/medium/large]_ribbon</li><li>4 square_lid_ribbon</li><li>1 gear</li><li>1 Topper from this project or any other Twist Lock Box Project</li></ul>All parts can be printed without supports.The spring works best if it's printed with enough perimeter lines to make the arms of the spring solid. This works better than just increasing the infill % because perimeter lines will flow in the direction of the spring arms.Make sure to print the correct number of lid ribbons and base ribbons.<h3> </h3><h3>Assembly</h3>Assembly is the same as the original <a target="_blank" href="https://www.prusaprinters.org/prints/81786-twist-lock-trick-box-hexagon" rel="nofollow noopener">Twist Lock Trick Box</a>. Watch <a target="_blank" href="https://youtu.be/1muiuHjyLlU" rel="nofollow noopener">this video</a> for the complete process.Make sure to pre-tension the sprint by one gear tooth This will assure that the latches have a strong hold on the base. This is also necessary for the alignment of some toppers.Make sure to glue the spring and topper If you do not fully secure these parts, the mechanism may become detached while in a locked state. I recommend using either super glue or <a target="_blank" href="https://www.3dgloop.com/" rel="nofollow noopener">3D Gloop!</a>, but hot glue can work as well.<h3> </h3><h3>Approximate Interior Dimensions</h3>Square<ul><li>Short: 70 x 70 x 36mm</li><li>Medium: 70 x 70 x 66mm</li><li>Tall: 70 x 70 x 96mm</li></ul><h3>Can I sell copies of this?</h3>Yes! This project was shared under the <a target="_blank" href="https://creativecommons.org/licenses/by/4.0/" rel="nofollow noopener">Creative Commons - Attribution</a> license.This license allows selling copies, but you must provide proper attribution, as detailed in the license itself.Please note that any other projects linked here (remixes or related projects) may have a different license. Please respect those licenses.<a target="_blank" href="https://wiki.creativecommons.org/wiki/best_practices_for_attribution" rel="nofollow noopener">Click here for attribution examples</a>

Twist Lock Present Square

present

Jaxel

I was looking for a way to stack multiple AMS on top of each other. There were several systems here on MakerWorld, but there were a few problems with them that I didn't like. Most importantly is that they weren't actually “stacking” systems. They let you put one AMS on top of another, but they could not stack beyond that. You could not stack a third, or even a fourth AMS in a single column. So I decided to make my own completely modular system that allows you to stack as many AMS you want!&nbsp;This system is sectioned off into 124mm “blocks”. There are two included wall heights, a “1-block” and a “2-block” wall. This allows you to raise your AMS to any height you want, at multiples of 124mm. If you want to simply put one AMS on top of another, you could print out walls in 3-blocks of height (2+1). This will allow enough space for you to slide the bottom AMS out in order to change filaments (like other AMS stacking systems). However, if wanted to be able to open the bottom AMS lid without having to slide it out, you would print out walls in 4-blocks (2+2) of height. Even more customizable, if you have under-AMS drawer systems, and you needed even more height between your AMS, you could print additional blocks of height to raise the top AMS even more!&nbsp;The “arms” that hold up the AMS are completely modular, and can be attached and removed at will. This has the advantage of being able to change arms without having to reprint your entire walls. So if your AMS breaks, and you buy a new one, and it turns out there is yet another new revision of the AMS, you can simply print out new arms that match the revision.&nbsp;<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=tUU1KRgZpPQ"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/tUU1KRgZpPQ" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;I have designed this model to be as easy and simple to print, with as little support material as possible. The included print profile has parts oriented in specific ways to minimize the chance of breakage due to lateral force, so part tension does not split at layer lines. There are several pre-defined plates:<ul><li>Plate 1:<ul><li>2x 2-block wall<ul><li>These models have support enforcers on the arm sockets.</li></ul></li></ul></li><li>Plate 2:<ul><li>2x 1-block wall<ul><li>These models have support enforcers on the arm sockets.</li></ul></li></ul></li><li>Plate 3:<ul><li>2x Rear Bracers<ul><li>Optional: if you want to have some extra rigidity to your stack to prevent “wobble”.</li><li>This system uses the AMS as a bracer. You want at least two sets of bracers on your stack.</li></ul></li><li>4x Dovetail Biscuits<ul><li>Connect the bracers to the rear of the walls.</li></ul></li><li>1x AMS (rear) Bracket<ul><li>This connects the AMS to a rear bracer, if you decided to print one.</li><li>This model is oriented at a 45 degree angle for strength.</li></ul></li><li>1x AMS (rear) Bracket Lock<ul><li>Locks the rear bracket in place so the middle pin doesn't shift.</li></ul></li></ul></li><li>Plate 4:<ul><li>2x AMS (side) Bracket<ul><li>These connect the AMS to the side walls through arm sockets.</li><li>These models are oriented at a 45 degree angle for strength.</li><li>Print these out in sets of two, one for each side of the AMS.</li></ul></li></ul></li><li>Plate 5:<ul><li>2x 2-block Blank<ul><li>Purely cosmetic, so things look nicer when you have rear bracers.</li><li>If you don't use rear bracers, then you don't need these blanks.</li></ul></li><li>8x Dovetail Biscuits<ul><li>Connect the blanks to the rear of the walls.</li></ul></li></ul></li><li>Plate 6:<ul><li>2x 1-block Blank<ul><li>Purely cosmetic, so things look nicer when you have rear bracers.</li><li>If you don't use rear bracers, then you don't need these blanks.</li></ul></li><li>4x Dovetail Biscuits<ul><li>Connect the blanks to the rear of the walls.</li></ul></li></ul></li><li>Plate 7:<ul><li>1x Blank (rear) Bracket<ul><li>A connector to attach both ends of a bracer if you printed a rear bracer without an AMS.</li><li>This model is oriented at a 45 degree angle for strength.</li></ul></li><li>4x Connector - Dowel<ul><li>Optional to keep your walls together when you stack them.</li></ul></li></ul></li></ul>I have included some additional STLs that you can peruse at your leisure, but they are not on plates.&nbsp;You can find other models I have released for the X1C/AMS here:<a target="_blank" href="https://makerworld.com/en/u/2811301167/collections/109412" rel="nofollow noopener">https://makerworld.com/en/u/2811301167/collections/109412</a>&nbsp;If you appreciate my models, please consider <a target="_blank" href="https://ko-fi.com/ultrajaxel" rel="nofollow noopener">buying me a coffee</a>!

AMS Stacking System

bambu x1

2emme3dlab

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmFilaments Used: PLA Eryone Black Transmission Distance: 5 PLA Eryone Red Transmission Distance: 5 PLA Eryone Yellow Transmission Distance: 5 PLA Eryone White Transmission Distance: 5&nbsp;Swap Instructions: Start with Black At layer #8 (0.72mm) swap to Red At layer #12 (1.04mm) swap to Yellow At layer #16 (1.36mm) swap to White for the rest.

Iron man HueForge

hueforge

michelem

<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000139309/design/2024-04-23_b4afa61493a71.png"></figure>A VERSATILE EVERYDAY COMPANION&nbsp;Imagine having a versatile tool that effortlessly fits into your pocket, ready to tackle an array of tasks.&nbsp;Meet the SmartBits – a compact marvel that seamlessly combines multiple functions in a sleek design.&nbsp;This tool serves as both a screwdriver and a bit holder, providing easy access to 8 different bits for various applications.&nbsp;Activating the tool is a breeze – a simple slide on the exposed bar causes the bits to extend from the opposite end. The magnet effortlessly guides them back into position. Never forget it open.&nbsp;Thanks to the additional embedded magnets, each bit is securely held in place, ensuring they remain steadfast whether you&#39;re on the move or storing the SmartBits in your pocket.&nbsp;It&#39;s the ideal companion for your everyday needs, effortlessly blending convenience and functionality.&nbsp;Print Instructions:&nbsp;Support is required for both the Base and the Slider. Please verify the 3mf file with Bambu Studio if there&#39;s any uncertainty.&nbsp;Place the Slider with the magnet holes on the build plate and add regular support.&nbsp;Position the Base with the side opening on the build plate and add regular support.&nbsp;There is an alternative version of the base with flat bottom you can print with it on the build plate, but it requires support too.&nbsp;No support is needed for the Button and Lid.&nbsp;I recommend printing everything with a minimum resolution of 0.16mm.&nbsp;Bill of Materials (BOM):&nbsp;You&#39;ll need some magnets and a few screws:<ul><li>12 magnets, 5 or 6mm x 2mm</li><li>4 screws, M3 Socket Head, 8mm</li></ul>Assembly Instructions:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000139309/design/2024-01-15_7862deb2dfe4.png"></figure>Start with the base and insert 2 magnets into the two rectangular holes; no glue is required there.&nbsp;Next, with a bit of glue, add 1 magnet to the Base in the slider housing. Be cautious, as this magnet is the only one that needs attention to its side, opposite to the one you put in the center hole of the slider (to be attracted).&nbsp;Now, take the Slider and glue 9 magnets on the bottom holes; again, the center one must have the same side as the magnet you put in the base slider housing.&nbsp;Insert the slider into the base, add the lid, and tighten the lid screws.&nbsp;Finally, attach the button to the slider with the last screw.&nbsp;If the slider doesn&#39;t return to its position, slightly loosen the screws.&nbsp;If you want I added also a cord endcap to be printed, look at the pictures, insert the paracord or similar in the bottom hole of the Endcap_Base make one simple knot on both ends, finally close it with the Endcap_Lid.&nbsp;Also, take a look at the <a target="_blank" href="https://makerworld.com/en/models/134027" rel="nofollow noopener">Magnetic Pocket Screwdriver</a> I crafted.&nbsp;Hope you like it!&nbsp;(Got inspired by the Bit Bar by Big Design)&nbsp;Check out my other magnetic tools for your office:&nbsp;<figure class="table" style="width: 94.97%"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td style="text-align: center"><figure class="image image_resized" style="width: 49.2%"><a href="https://makerworld.com/en/models/146614" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000139309/design/2024-01-23_b0f041b578fc2.png"></a></figure></td><td style="text-align: center"><figure class="image image_resized" style="width: 50.26%"><a href="https://makerworld.com/en/models/143760" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000139309/design/2024-01-23_bf112a67f1d5b.png"></a></figure></td></tr></tbody></table></figure><ul><li><a target="_blank" href="https://makerworld.com/en/models/146614" rel="nofollow noopener">The magnetic cable clips</a></li><li><a target="_blank" href="https://makerworld.com/en/models/143760" rel="nofollow noopener">The magnetic ScrewGuard</a></li></ul>

SmartBits - Magnetic screwdriver bits holder

tools

Reuter_Corp.

Lightbox - Mountain river  Step 1 : Glue Frame A&B  <figure class="image image_resized" style="width:41.27%;"><img src="https://makerworld.bblmw.com/makerworld/draft/418506/2024-01-18_6a1a0dab0e36b.jpg"></figure><figure class="image image_resized" style="width:40.34%;"><img src="https://makerworld.bblmw.com/makerworld/draft/418506/2024-01-18_05c4cad3d741b.jpg"></figure><figure class="image image_resized" style="width:40.7%;"><img src="https://makerworld.bblmw.com/makerworld/draft/418506/2024-01-18_ea28812170f1.jpg"></figure><figure class="image image_resized" style="width:39.96%;"><img src="https://makerworld.bblmw.com/makerworld/draft/418506/2024-01-18_a4048a6d0c099.png"></figure>  Step2 : LED Stripe Put the Led Stripe around the bottom perimeterstart at the power input like so:<figure class="image image_resized" style="width:28.74%;"><img src="https://makerworld.bblmw.com/makerworld/draft/418506/2024-01-18_b2655ad1e36f2.jpg"></figure>&nbsp;<figure class="image image_resized" style="width:29.35%;"><img src="https://makerworld.bblmw.com/makerworld/draft/418506/2024-01-18_3b66d9478fcba.jpg"><figcaption> </figcaption></figure>&nbsp;If you need help let me knowthanks hope you enjoy&nbsp;

art

stargate

present

bambu x1

hueforge

tools

led lampen