Banthony245

gwenhidwy

**Update 1/3/2024**I noticed a small number of people having issues with fit of the trays. I fixed a small defect that may have been causing this. I have replced the old versions with V2.&nbsp;**Update 12/29/23**I added a profile for the A1 Mini, with trays of slightly reduced width and length.&nbsp;**Update 12/20/23**I added a single profile with multiple plates.&nbsp;I use these to sort lego when building or sorting bulk but they could be used for just about anything.There are three different sizes in this set plus a lid and they stack:<ul><li>Large</li><li>Medium</li><li>Small</li><li>Lid</li></ul>I also have plates with multiple copies of the smaller trays on the build plate, for connivence<ul><li>Medium x 2</li><li>Small x 4</li></ul>These can be printed without supports.&nbsp;Please checkout some of my related models:<figure class="table"><table><tbody><tr><td><h2><a target="_blank" href="https://makerworld.com/en/models/122893#profileId-132376" rel="nofollow noopener">Bento Stax</a></h2></td><td><h2><a target="_blank" href="https://makerworld.com/en/models/61141#profileId-63332" rel="nofollow noopener">Nesting Trays - 2U Tall</a></h2></td><td><h2><a target="_blank" href="https://makerworld.com/en/models/16636#profileId-15428" rel="nofollow noopener">Stackable Funnel Trays</a></h2></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/350807/2024-01-04_b544c2c49c185.jpeg"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/350807/2024-01-04_375d3f7708a92.jpeg"></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/350807/2024-01-04_1e3a115bbe906.jpeg"></figure></td></tr></tbody></table></figure>

Nesting Trays

to print

Darth Vader

A Vallejo paint holder, which utilises the full width of the 76x56cm Ikea Skadis peg board. A total of 140 paints can be stored per board. Model is split into 4 easy to print pieces over 2 beds. Print 4 of the standard holders and 1 upper.&nbsp;I wanted to get as much paint as I could onto the pegboard. You will be able to fit 5 x rows per board, each row will hold 28 x paints. I have tested it with Vallejo, Green Stuff World and Army painter. This is around 3 to 4 more paints per row than traditional holders.&nbsp;Please ensure that the rear pegs are supported across their length. The included 3mf are pre-supported.&nbsp;I have uploaded a STEP file for a better overall print if you decide not to use the 3mf. Also any adjustments/remix can be made if need be.&nbsp;Each part is numbered at the back.&nbsp;I'd suggest a minimum of 3 walls to ensure the pegs are strong enough.&nbsp;*** V2 now added following a request.  This version allows you to see more of the bottle label and reduces the amount of filament, however it's strength will be effected.  I have not tested this, so use at your own risk ***&nbsp;&nbsp;PLEASE NOTE. Although very unlikely, some slight variation in slot diameter and distance between slots may be possible with some Skadis boards. Most are within tolerance, but if it doesn't fit, then please understand this is out of my control. I have printed 7 now and all slot perfectly into my board.