大猫

<p>*** BREAKING NEWS ***</p><p>ATTENTION: <strong>65 mm</strong> long toothpicks &amp; <strong>0.2 mm</strong> layer height is required for this version!</p><p>ACHTUNG: Für diese Version werden <strong>65 mm</strong> lange Zahnstocher &amp; <strong>0,2 mm</strong> Schichthöhe benötigt!</p><p>*** *** *** *** *** ***</p><p>&nbsp;</p><p>************ <strong>UPDATE</strong> ************</p><p>I&#39;m still collecting suggestions for <strong>Version 3</strong>. Let me know in the comments if there&#39;s anything missing:</p><p>1.   65 to 68 mm toothpicks must fit<br>2.   Container for approx. 100 toothpicks<br>3.   Design without text and symbols</p><p>4.   Shouldn&#39;t look like a Chinese coffin, but more like a Porsche</p><p>********************************</p><p>&nbsp;</p><p>I love mechanical &#34;Print-In-Place&#34; models. And sometimes I enjoy clicking or screwing things together after printing.</p><p>But why shouldn&#39;t my 3D printer handle that if it can do it much better than I can...</p><p>Inspired by various models and 3D printing techniques, I proudly present my latest creation. After numerous prototypes, your printer should be able to produce this toothpick dispenser without any post-processing or assembly.</p><p>&nbsp;</p><p>I hope this little gadget brings you as much joy as it did for me while developing it.</p><p>&nbsp;</p><p>PS: The version number is written inside. I look forward to your feedback and suggestions for improvement.</p><p>Updates will follow...</p><p>&nbsp;</p><p>***********************</p><p>&nbsp;</p><p>Mechanischer Zahnstocher Spender – Einteiler, keine Stützen, keine Montage, keine Nachbearbeitung.</p><p>&nbsp;</p><p>Ich liebe mechanische «Print-In-Place» Modelle. Und manchmal mag ich es, wenn ich nach dem Druck etwas zusammen klicken oder schrauben kann.</p><p>Aber warum sollte das nicht mein 3D Drucker machen, wenn er das doch viel besser als ich kann…</p><p>Inspiriert von verschiedenen Modellen und 3D-Druck Techniken präsentiere ich nun meine neueste Kreation. Nach zahlreichen Prototypen sollte nun auch dein Drucker diesen Zahnstocher Spender ohne Nachbearbeitung und zusammen friemeln ausspucken.</p><p>&nbsp;</p><p>Ich hoffe dieses kleine Gadget bereitet euch genau so viel Freude wie mir beim Entwickeln.</p><p>&nbsp;</p><p>PS: Im Inneren ist die Versionsnummer angeschrieben. Ich freue mich auf euren Feedback und Verbesserungsvorschläge.</p><p>Updates werden folgen…</p>

Toothpick Dispenser - Print in Place - No Supports

日常物品

Brian Dean

<h2><strong>Embedded Magnet Dispenser Tool for Multiple Diameters and Thicknesses</strong></h2><h3>PROFILE NOTE</h3><p><strong>Please use the “Designer” profile as it guarantees the latest files and version with all new magnet sizes and features. The Designer Profile will be listed at the top.</strong></p><h3>Latest Update (2024-04-21): Quick summary</h3><ol><li>additional magnet sizes</li><li>magnet size text embossed on the barrel and also included on the slider</li></ol><p>See below for the more detailed update notes.</p><h2><strong>Magnet Dispenser for 3D Prints: Simplify Magnet Insertion with Precision</strong></h2><p><span style="color:rgb(55,65,81);font-size:16px;">The Magnet Dispenser Tool is expertly designed to streamline the insertion of magnets into 3D prints. This tool not only speeds the process of inserting magnets into 3D Prints, it also ensures correct orientation and secure fitting, making it ideal for projects that require precise magnet placement.</span></p><h3><strong>Key Features</strong></h3><h4><strong>Dual Dispensers for Perfect Alignment</strong></h4><ul><li>Includes two dispensers for each magnet size – one for north-up and one for south-up orientations</li><li>Use different colors (e.g., red for north-up and blue for south-up) to help easily identify the dispenser&#39;s orientation</li><li>Eliminates the hassle of misaligned magnets</li></ul><h4><strong>Design and Utility</strong></h4><ul><li>Developed after extensive refinement</li><li>Allows for friction-fit insertion and is also suitable for magnets that are glued</li><li>Tapered tip facilitates use in tight spaces</li></ul><h4><strong>Ease of Use</strong></h4><ul><li>The dispensers are designed to accommodate the specified magnet sizes for their internal holding magnets, but can dispense magnets of any thicknesses for the specified diameter. For example, for the 6x3mm dispenser, you will need 6x3mm magnets to assemble the dispenser, but once assembled, that dispenser can dispense any 6mm diameter magnet such as 6x1, 6x2, 6x3, 6x5, etc.</li></ul><h4><strong>Convenience and Storage</strong></h4><ul><li>Features a snap-on cap with an embedded magnet and a top slider magnet</li><li>Ensures secure storage and prevents accidental magnet spillage</li></ul><h4><strong>Customization and Printability</strong></h4><ul><li>No supports needed for printing</li><li>STL and STEP files included for personal customization</li><li>Compatible with PETG, PLA, ASA, ABS, etc</li><li>Adjust x/y hole compensation if needed for perfect fit</li></ul><h4><strong>Visual Guide</strong></h4><ul><li>Fusion 360 images provided for easy assembly and understanding of the internal mechanism</li></ul><h4><strong>Use the Magnet Dispenser for a hassle-free, precise, and efficient magnet insertion experience in your 3D printing projects.</strong></h4><h3>Supported Magnet Sizes</h3><h4>Dispensers are now provided for the following magnet sizes as of <i>Version 5</i></h4><ol><li>2x1mm</li><li>2x2mm</li><li>2x3mm</li><li>3x1mm</li><li>3x2mm</li><li>3x3mm</li><li>4x1mm</li><li>4x2mm</li><li>4x3mm</li><li>5x1mm</li><li>5x2mm</li><li>5x3mm</li><li>6x2mm</li><li>6x3mm</li><li>7x2mm</li><li>7x3mm</li><li>8x2mm</li><li>8x3mm</li><li>8x4mm</li><li>9x2mm</li><li>9x3mm</li><li>10x1mm</li><li>10x2mm</li><li>10x3mm</li><li>12x2mm</li><li>12x3mm</li><li>15x2mm</li><li>15x3mm</li><li>20x2mm</li><li>20x3mm</li></ol><p>NOTE 1: The 1mm magnet thickesses are just too thin to work reliably with the friction-fit of the slider and caps. Therefore, I have made the pockets of the “1mm” thickness magnet dispensers to be that of the 3mm variety so that they work. So to assemble a 1mm magnet thickness dispenser, you will need to purchase a few 3mm thick magnets to assemble the dispenser. A 2mm thickness will likely work ok, too. Note that the text on the dispenser will still say “D x 1 mm” for the barrel, “Dx1” on the cap, and “D/1” on the slider, so you know what magnets you have loaded into it.</p><p>&nbsp;</p><p>NOTE 2: the above are the sizes needed to assemble the dispenser. The dispenser can still dispense any thickness of magnet as long as the diameter is the same. So if don&#39;t see your specific magnet thickness listed above, you can still print the correct diameter, assemble the dispenser with the correct magnet thickness, and dispense other thicknesses.</p><p>&nbsp;</p><p>STEP and STL raw files are included if you do not wish to use the provided profile.</p><h3>Quality Assurance Testing</h3><ul><li><span style="color:rgb(55,65,81);font-size:16px;">All dispenser sizes have been printed by me and extensively tested</span></li><li><span style="color:rgb(55,65,81);font-size:16px;">I have purchased all magnet sizes at significant expense to myself to ensure fit</span></li><li><span style="color:rgb(55,65,81);font-size:16px;">Magnet diameters are tricky for press-fit tolerance and controlled by no less that 5 Fusion 360 parameters that must be balanced to achieve good fit</span><ul><li><span style="color:rgb(55,65,81);font-size:16px;">Multiple iterations of each dispenser were printed and refined</span></li><li><span style="color:rgb(55,65,81);font-size:16px;">Many kilograms of filament and hundreds of hours of print-time were consumed during this process</span></li><li><span style="color:rgb(55,65,81);font-size:16px;">All to ensure the best quality printing and fit-up for each dispenser size</span></li></ul></li></ul><h3>About the Profiles</h3><ol><li>Please use the “Designer” profile as it guarantees the latest files and version with all new magnet sizes and features. The Designer Profile will be listed at the top.</li><li>NOTE: The “Designer” profile is a single profile that contains plates for all magnet sizes so far. Please ignore the “total time” reported by MakerWorld for the profile. You only need to print the plate(s) that you need. Each plate takes about 2.5-2.9 hours on my X1C using the included “PETG” profile which is slowed down for good PETG layer adhesion and quality.</li><li>While the other profiles may be ok, their file / update version may be out of date. So if you want the latest sizes and model improvements, please choose the top “Designer” profile.</li></ol><h3>Accessories</h3><p>Be sure and check out some nice accessories that other folks have created to work with these dispensers.</p><ul><li><strong>Tip Caps</strong> - these are nice caps for the dispensor tip. Not only do they help keep the magnets contained within, but they also protect the tip. Additionally, they are labeled with the magnet size, which is nice. Thank you @onegotowned ! <a target="_blank" href="https://makerworld.com/en/models/149038#profileId-162633" rel="nofollow noopener">https://makerworld.com/en/models/149038#profileId-162633</a></li><li><strong>Vertical Workbench Stand</strong> - This is a very nice stand for select diamagers made by @nickramsey57. A number of folks have asked about stands / organizers for the dispensers, so this model will likely be useful to a number of folks. Thank you @nickramsey57 ! <a target="_blank" href="https://makerworld.com/en/models/206388#profileId-226561" rel="nofollow noopener">https://makerworld.com/en/models/206388#profileId-226561</a></li><li><strong>Vertical Workbench Stand (parametric)</strong> - Here is another very nice stand made by @RevHazlett. You can specify the dispenser sizes that you want it to hold and then generate, making it customizable to your needs and the common magnet sizes that you use. Thank you @RevHazlett! <a target="_blank" href="https://makerworld.com/en/models/435087#profileId-340031" rel="nofollow noopener">https://makerworld.com/en/models/435087#profileId-340031</a></li></ul><h2>Update History</h2><h3>Version 5: 2024-04-21</h3><ol><li>Emboss the magnet size text on the Barrel (see photos), allowing one to view the size from the side, and also allowing one to print all of the barrels on a single plate and not get the barrels mixed up as to what size they are for.</li><li>Include the magnet size text on the Slider (see photos), allowing one to print all of the sliders and caps together on one plate and not get the sliders mixed up as to what magnet size they are for. Also provides additional text identification of the magnet size within.</li><li>Include 11 new magnet sizes:<ol><li>3x1mm</li><li>4x1mm</li><li>5x1mm</li><li>7x2mm, 7x3mm</li><li>8x4mm</li><li>10x1mm</li><li>15x2mm, 15x3mm</li><li>20x2mm, 20x3mm</li></ol></li><li>Re-organize the plates so that they are a little easier to manage. All dispenser sizes for each “diameter” are spread across three plates now - the Barrels, the Red Caps and Sliders, and the Blue Caps and Sliders. This allows one to “print-by-layer” instead of “print-by-object”, and the text also comes out better. Additionally, it is now easier to construct a plate with all of the size variations on 3 individual plates and print them all at once.</li></ol><h3>Version 4: 2023-12-26</h3><ol><li>Fixed an issue where the smaller diameter magnets such as the 2mm, 3mm, and possibly the 4mm magnet diameters could inadvertently slip through the vertical barrel slider stem slot. Prior to this update, the slider stem was a fixed 3mm + tolerance width. With Version 4, the slider slot is now dynamic based on the magnet diameter. So now, the smaller diameter magnets are captive within the barrel and cannot slip out inadvertently.</li><li>Tighten up the tolerances between the “slider” and the “barrel” for a better fit and smoother operation.</li><li>Use the Profile: “Version 4: All Sizes …” for the latest from this update.</li></ol><h3>Version 3: 2023-12-22</h3><ol><li>Added additional magnet sizes<ol><li>2x1mm, 2x2mm, 2x3mm</li><li>9x2mm, 9x3mm</li></ol></li><li>Text is now added within the Fusion 360 Model File, eliminating the need to add the text using Bambu Studio<ol><li>Ensures consistent text placement and easier colorizing of the text</li></ol></li><li>All plates are included for all magnet sizes, two dispensers per plate, print sequence: print-by-object</li></ol><h3>Version 2.1: 2023-11-28</h3><ol><li>Added additional magnet sizes<ol><li>3x2mm</li><li>4x2mm, 4x3mm</li><li>5x2mm, 5x3mm</li><li>6x2mm</li><li>8x2mm, 8x3mm</li><li>10x2mm, 10x3mm</li><li>12x2mm</li></ol></li><li>The magnet size text is included on the cap for easy identification - see photo</li></ol><h3><strong>Version 2: 2023-11-20</strong></h3><p>Updated to “Version 2”. Significant updates an enhancements have been made, some seen, some unseen.</p><ol><li>Added additional magnet sizes<ol><li>3x3mm</li><li>12x3mm</li></ol></li><li>Each magnet size is on its own plate, two dispensers per plate, print sequence: print-by-object</li><li>Redesigned “thumb slider” for greater comfort and stronger press force</li><li>Slider stem has been reinforced</li><li>Many enhancements for smoother operation with internal chamfers and fillets, enhanced tolerances, and strengthening of key internal components</li></ol><p>&nbsp;</p><p>&nbsp;</p><p>&nbsp;</p>

Embedded Magnet Dispenser Tool for 3D Prints

日常工具

blecheimer

<p>These are two simple bezels for the Bambu Lab P1P / P1S screen. Choose what you prefer.<br>They will be pressed on the screen from the front and clip to the screen on the backside. Yes, it is a tight fit - if it is too tight for you then you can scale the model with the slicer in z-direction by +0.1 or +0.2% and print again.</p><p>&nbsp;</p><p>Disclaimer:<br>This work by blecheimer is licensed under <a target="_blank" href="http://creativecommons.org/licenses/by-nc-sa/4.0/?ref=chooser-v1" rel="nofollow noopener">CC BY-NC-SA 4.0</a><br>You are not allowed to copy this model to other 3D printing websites without my permission.</p>

Minimalist Screen Bezel for Bambu Lab P1P / P1S 

打印机配件工具

Printcells

<p>Riot games key tags</p><ul><li>We used PLA SILK Copper</li><li>Choose your colors</li><li>Enjoy !</li></ul>

Riot games key tags collection

游戏

Lucky 13 Toys

<h3>Dummy 13 is now on a CC BY 4.0 license!</h3><p>This means that you are free to share these files however you like,<i> including selling prints,</i> <strong>provided that you give proper attribution. </strong>You can give proper attribution by including this notice on your product page:</p><figure class="table"><table><tbody><tr><td><a target="_blank" href="https://makerworld.com/en/models/183780#profileId-202639" rel="nofollow noopener">DUMMY 13 Printable Jointed Figure </a>© 2023 by <a target="_blank" href="https://www.lucky13toys.com/" rel="nofollow noopener">Lucky 13 Toys </a>is licensed under <a target="_blank" href="http://creativecommons.org/licenses/by/4.0/?ref=chooser-v1" rel="nofollow noopener">CC BY 4.0 </a></td></tr></tbody></table></figure><p>Please help me build my identity as a creator by referring to this design by its original name. <strong>Don't pass off my work as your own product. </strong>Too many people are doing that already!</p><p>&nbsp;</p><p>Want to support future projects with a one-time donation? <a target="_blank" href="https://www.paypal.com/donate/?business=65FUQ2SJMYDDS&no_recurring=0&item_name=Thanks+for+supporting+Lucky+13%21&currency_code=USD" rel="nofollow noopener">Make a PayPal donation here!</a></p><p>&nbsp;</p><p>&nbsp;</p><p>&nbsp;</p><p><a target="_blank" href="https://www.printables.com/@soozafone/activity/4153" rel="nofollow noopener">This is my own work, originally uploaded to Printables.</a></p><p>&nbsp;</p><p>Yes, Dummy 13 is now on MakerWorld.</p><p>&nbsp;</p><h3>Please read before printing:</h3><p><strong>This is a work in progress.</strong> It has been collecting virtual dust while I work on other projects, so I've decided to release it now in a “beta” state. I don't have a timeline for when the final version will be finished, but the current files are fairly complete - just lacking some perfectionist polish. Please understand that there is some room for improvement here. I welcome your feedback to help make this design the best it can be.</p><p>&nbsp;</p><p><strong>What's finished right now:</strong> Design of all parts, except for minor tweaks based on feedback. Basic instructions.</p><p>&nbsp;</p><p><strong>What's not finished: </strong>Parts on runners for better adhesion without brims. More detailed instructions. Fusion 360 and STEP files for Printables Club members (please note that these will not be available until the design is finalized). Any updates based on feedback.</p><p>&nbsp;</p><p><strong>Can I sell it? </strong>Yes, Dummy 13 is distributed under a CC BY 4.0 license that does allow commercial use, provided that you provide proper attribution.</p><p>&nbsp;</p><p>If you'd like to say thanks and help support future development, you can make a one-time donation <a target="_blank" href="https://www.paypal.com/donate/?business=65FUQ2SJMYDDS&no_recurring=0&item_name=Thanks+for+supporting+Lucky+13%21&currency_code=USD" rel="nofollow noopener">here</a> :)</p><p>&nbsp;</p><p>---</p><p>&nbsp;</p><h3>Introducing Dummy 13!</h3><p>(…working title.)</p><p>This is another variant on <a target="_blank" href="https://www.printables.com/model/148367-lucky-13-printable-jointed-figure" rel="nofollow noopener">Lucky 13</a>, and I actually started designing it before <a target="_blank" href="https://www.printables.com/model/422353-mini-13-printable-jointed-figure" rel="nofollow noopener">Mini 13</a> or <a target="_blank" href="https://www.printables.com/model/555170-easy-13-printable-jointed-figure" rel="nofollow noopener">Easy 13</a>. As you can probably tell, my goal here was to bring some more humanlike proportions to the figure, while also improving the way everything fits together.</p><p>&nbsp;</p><p>My hope is that this will be an easier print than the original Lucky 13, though still a step up from Mini and Easy.</p><p>&nbsp;</p><h3>Printing</h3><p>As with the original, Dummy 13 is made up of an inner "frame" with a layer of “armor” over top. You can use the material of your choice for the armor, but you should print the frame with a strong and sturdy material like ABS, ASA, or PETG. I mostly use ASA.</p><p>&nbsp;</p><p><strong>PLA is not recommended for the frame. </strong>If you print the frame in PLA and complain that it broke or went floppy, I'm going to be like, “yeah dude, I told you not to.”</p><p>&nbsp;</p><p>All parts print without supports and you should not need to reorient anything. <strong>Bed adhesion is the toughest part of this print. </strong>For better adhesion try slowing down your first layer, printing external perimeters first, and adding a brim if needed. Use 0.15mm layers (0.2mm first layer).</p><p>&nbsp;</p><p>You can use the included 3MF files with pre-plated parts, or arrange the individual parts yourself. If a part starts with “2x” or “4x,” print that many copies. There are also a couple extra bits (a simple staff accessory and an adapter for the <a target="_blank" href="https://www.printables.com/model/563861-lucky-13-display-base-20" rel="nofollow noopener">display base</a>) that are included separately.</p><p>&nbsp;</p><p><strong>Recommended print settings (100% scale, 0.4mm nozzle)</strong></p><figure class="table"><table><tbody><tr><td rowspan="2">Material</td><td>Frame parts</td><td>ABS, ASA, or PETG</td></tr><tr><td>Armor parts</td><td>Any</td></tr><tr><td rowspan="2">Layer height</td><td>First layer</td><td>0.2 mm</td></tr><tr><td>Other layers</td><td>0.15 mm</td></tr><tr><td colspan="2">Infill</td><td>20% rectilinear</td></tr><tr><td colspan="2">First layer speed</td><td>25% of default</td></tr><tr><td colspan="2">Elephant foot compensation</td><td>0.15 mm</td></tr><tr><td colspan="2">Supports</td><td>None</td></tr><tr><td colspan="2">Brim</td><td>As needed (depends on bed adhesion)</td></tr><tr><td colspan="2">Additional settings</td><td>☑ Print external perimeters first</td></tr></tbody></table></figure><p>&nbsp;</p><h3>Assembly</h3><p>Follow this video for assembly instructions. Pay attention - some parts look very similar!</p><figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=Rwu3UP0cHZw"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/Rwu3UP0cHZw" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure><p>&nbsp;</p><h3>Customizing</h3><p>Dummy 13 should be compatible with most handheld accessories made for my other designs. Check out Lucky 13's <a target="_blank" href="https://www.printables.com/model/148367-lucky-13-printable-jointed-figure/remixes" rel="nofollow noopener">remixes page</a> for a good starting point!</p><p>&nbsp;</p><p>&nbsp;</p><p>This design has already been stolen and stripped of attribution a hundred times over. Please don't add to that.</p>

日常物品

日常工具

打印机配件工具

游戏

玩具