BEAMink

BATTCAVE

Threaded Skull Stash Jar - 75mm&nbsp;Detailed skull jar with TIGHT fitting threaded lid. Flange is designed to offer a VERY snug final turn so it wont open by itself.&nbsp;Work the threads in a bit and they will get smooth, a little wax makes them buttery smooth. Don&#39;t just try and force it. Especially if you have any stringing. Clean that out FIRST. &nbsp;This is my absolute favorite lube for plastic models: https://www.amazon.com/Squirt-Clean-Long-Lasting-Chain/dp/B00OBUTM4U&nbsp;Scalable - Example printed in Sunlu Matte PLA.&nbsp;Version 2 is up here: https://makerworld.com/en/models/501470#profileId-416521

Threaded Skull Stash Jar - 75mm 

Containers

MakerVerse Designs

Fully 3d printed crocs shoes<ul><li>Printed with Overture TPU</li><li>PLA for the snap button</li></ul>Important notes:<ul><li>It is for EU shoe size number 42 (male), but you can scale every part (CrocsL1,CrocsR1,Holder,Mount1,Mount2) to your size (use uniform scaling)</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000425034/design/2024-04-19_0266f756a989a.png"></figure><ul><li>If the shoe is too big to fit to the printers height, use the “WithSupport”-Version, rotate in Y-Axis (green) and use the cut tool in Bambu Studio to create a new flat surface parallel to the print bed<ul><li>I uploaded an .stl file without cut on the bottom for better scaling</li></ul></li></ul>&nbsp;<ul><li>There are two ways to print this:</li></ul><ol><li>Use a textured PEI bed and print it standing up without support</li><li>Or use another not so sticky bed and print it standing up with support</li></ol><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000425034/design/2024-04-12_cc0523cbae068.png">&nbsp;If you can&#39;t get enough of printed shoes, check out my new model (Slide Shoes, Adilette):<a target="_blank" href="https://makerworld.com/en/models/488792#profileId-401842" rel="nofollow noopener">https://makerworld.com/en/models/488792#profileId-401842</a><img class="image_resized" style="width: 41.76%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000425034/design/2024-06-08_bb258037ea2a1.png">Have fun with it and leave a like or subscribe if you like it!If there are any suggestions for improvement, feel free to write a comment.

Crocs Shoes - Fully 3d-printed

Shoes

melchior.geurts

A print in place string winder. Easy to print, you might need to break the handle loose.&nbsp;Print time: 43 min Filament amount: 20 grams Filament type: PLA

Guitar string winder tool Print in place

Instrument tools 

martinMaker

Laptop Stand

Computer Accessories

Michael Rechtin

&nbsp;Full Build Detailed in Youtube Video:<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=h6chNEaXb-o"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/h6chNEaXb-o" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>Hardware List: (Affiliate Links) Motors: <a target="_blank" href="https://amzn.to/4c5N0SW" rel="nofollow noopener">https://amzn.to/4c5N0SW</a> Flight Controller: <a target="_blank" href="https://amzn.to/43eu3ZS" rel="nofollow noopener">https://amzn.to/43eu3ZS</a> DJI O3: <a target="_blank" href="https://amzn.to/431EGiR" rel="nofollow noopener">https://amzn.to/431EGiR</a> 2mm Bullet Connector: <a target="_blank" href="https://amzn.to/3In6B3l" rel="nofollow noopener">https://amzn.to/3In6B3l</a> LEDs: <a target="_blank" href="https://amzn.to/3uV63hX" rel="nofollow noopener">https://amzn.to/3uV63hX</a> Props: <a target="_blank" href="https://amzn.to/3IpEkc9" rel="nofollow noopener">https://amzn.to/3IpEkc9</a> 4s 1300mah Batteries: <a target="_blank" href="https://amzn.to/436hHmL" rel="nofollow noopener">https://amzn.to/436hHmL</a> M4x12 Bolt: <a target="_blank" href="https://amzn.to/3T6co23" rel="nofollow noopener">https://amzn.to/3T6co23</a>&nbsp;FPV Equipment (Other products may be able to be substituted): RC Controller: <a target="_blank" href="https://amzn.to/3VbpZYy" rel="nofollow noopener">https://amzn.to/3VbpZYy</a> FPV Goggles: DJI FPV Goggles V2

100MPH FPV Race Quad

Drones & RC Planes

Willi 3D

Create your own battle droid army and take over the galaxy!&nbsp;If you like this model, please throw me a like. Designing the models is time, filament and coffee consuming. <a target="_blank" href="https://www.paypal.com/donate/?hosted_button_id=WGL5LXN5EHEXN" rel="nofollow noopener">If you want to support my work bye me a coffee.</a> Thanks!&nbsp;Description:This is a KIT CARD remix of my B1 battle droid. I changed the design in many places to make it easier to assemble and allow the figure to stand and pose on its own. Check out the compatible <a target="_blank" href="https://makerworld.com/de/models/13746?profileId=13457" rel="nofollow noopener">STAP speeder bike</a>!Scale 1:9 (90% for 1:10)&nbsp;Improvements:- improved connection points- easier to assemble- improved stand and pose of the figure- Blaster *pio* *pio*- kit cardsMay the force be with you!Roger roger!&nbsp;Update:(21/08/23) <ul><li>optimized base</li></ul>(03/08/23) <ul><li>optimized size for smaller printer and better to print fingers</li><li>addet base and insert to chest </li></ul>(26/07/23) <ul><li>optimized fit of head, thin, pipe, backpack and blaster</li><li>addet thumb to forarm, hole for blaster in backpack</li></ul>(13/07/23) <ul><li>optimized fit of ankle and blaster</li></ul>&nbsp;Printing:Layer height: 0.1Supports: NoBrim: NoMaterial: PETG, (ABS), (PLA)&nbsp;Assembly: The connections are designed and optimized for PETG, the use of PLA or ABS makes assembly more difficult.It is better to rotate the knee and elbow joints than to push them into place.In order to replicate the design of the B1 battle droid as closely as possible, I was forced to make some parts very fragile. Please be ready to reprint parts in case of breakage. Separate parts are located in the respective folders.

Kit Card B1 Battle Droid Star Wars 

Movie Themed 

Titan3DPrintingAU

Single bed print of a Mandalorian Helmet. Have included the Raw files as well as the file broken up (in RAW form)

Mandalorian Helmet

Cosplay

Powerpill.prints

<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-02-18_5fb8e169839cd.png"> This pack has been all set up for super simple and easy printing with the AMS or AMS lite!All the models are set to 2 - 4 Colours! Just load your filament, slice and go!<boostme><boosttitle>Boost Me</boosttitle><boostcontent>If you enjoyed these keychains, please consider boosting to support the creator. Thank you!</boostcontent></boostme>Most keychains take between 45 minutes to 1.5h to print!<h2>This Keychain pack has 50 items in it separated onto 36 different plates! Games included:</h2><h3>Metroid, Zelda I &amp; II, Duck Hunt, Super Mario Brothers, Dr. Mario, Punch Out, Donkey Kong, Ice Hockey, Excitebike, Balloon Fight, Kid Icarus, and Ice Climber!</h3><h2>Check out My other Video Game Keychain Packs here:</h2><figure class="table"><table><tbody><tr><td><figure class="image"><a href="https://makerworld.com/en/models/136252#profileId-148211" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-02-16_bf102988c5d4e.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/136252#profileId-148211" rel="nofollow noopener">Super Mario Bros. 3 Keychain Pack</a></td><td><figure class="image"><a href="https://makerworld.com/en/models/177083#profileId-194702" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-02-16_af8e11b72f8b8.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/177083#profileId-194702" rel="nofollow noopener">Pokemon Keychain Pack #4</a></td><td><figure class="image"><a href="https://makerworld.com/en/models/121800#profileId-131121" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-02-16_d591f34521b71.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/121800#profileId-131121" rel="nofollow noopener">Pokemon Keychain Pack #1</a></td></tr></tbody></table></figure>All models have been test printed on the A1 Mini with the AMS Lite!  <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-02-16_65642b6d44be1.png">I have this set to use the 0.4mm nozzle with a .28mm layer height. This prints three layers of colour so the colours turn out nice and saturated and minimize waste. After the colour, there&#39;s one solid black layer, three layers of infill, and four final solid layers for the back for strength with the back pattern set to Hilbert Curve for a nice texture. There is a small hole in each model which is just large enough to fit a 1mm keychain jump ring. If you find it too small, you can modify the size of the “Keychain hole” object in BambuStudio to make it a little larger, or take a small drill bit and drill the final keychain to make it a little bigger!&nbsp;I purchased my <a target="_blank" href="https://www.amazon.ca/gp/product/B07DC9YZXV/" rel="nofollow noopener">keychain set from Amazon</a> if you&#39;d like to get something similar!&nbsp;<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-02-16_39c8a218834e3.png">All models have been flipped face down on the print bed so the surface texture from the PEI plate gives them a nice textured surface! All the different pieces of the models are there if you want to play around with it. There is one black ‘back’ piece in each keychain, which is perfectly aligned to the rest of the model. This causes some flickering in the viewport when moving around, but it disappears after slicing. If you modify the settings of that piece, it will affect the infill settings, so if you want to save a little filament, feel free to adjust it there!<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-02-20_5772d38e54629.gif"></figure>I made some changes to the first layer and first layer infill speeds, reducing them both by about half. This increases the print time for the first layer, but increases the bed adhesion and print quality a bit. If you find that the first layer is printing too slow for your liking, feel free to reset them both back to default settings in the speed tab.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-01-15_c5fc221922c1c.webp"></figure>If you want some extra crisp pixels, you can try printing these with the 0.2mm nozzle, but I didn&#39;t think the increased print time was really worth the extra quality. It&#39;s definitely noticeable, but I didn&#39;t think the tradeoff was there. Feel free to experiment and try it yourself!<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-02-16_e1de8136a8cba.png">Want to remove the keychain hole? No problem! Each keychain has a “Keychain hole” object on each plate. Just select it, delete it, and re-slice!<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-02-20_652472aa40ac8.gif"></figure>Want to scale these up really large to make some wall art? Just delete the “Keychain hole” object, then scale the X and Y axis to fit your print bed. Keep the Z-Scale back to 3.08mm so you&#39;re not printing extra layers though!<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-02-20_5bb325e63de11.gif"></figure>If you notice any settings that could be changed or improved, please let me know! I&#39;d love to make any adjustments necessary so they all print great! If there&#39;s any other packs or characters you want to see, leave a comment! Like this pack? Check out my other video game keychain packs here:  <figure class="table" style="height: 261.055px; width: 960px"><table style="background-color: rgb(255, 255, 255); border: 1px double rgb(179, 179, 179)"><tbody><tr><td style="border: 1px solid rgb(191, 191, 191); padding: 0.4em"><figure class="image"><a href="https://makerworld.com/en/models/172935#profileId-189959" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-02-16_bee3dac9a4a4f.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/172935#profileId-189959" rel="nofollow noopener">Pokemon Keychain Pack #3</a></td><td style="border: 1px solid rgb(191, 191, 191); padding: 0.4em"><figure class="image"><a href="https://makerworld.com/en/models/162397#profileId-178258" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-01-29_ca2f6c28ed6ef.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/162397#profileId-178258" rel="nofollow noopener">Kirby Keychain Pack</a></td><td style="border: 1px solid rgb(191, 191, 191); padding: 0.4em"><figure class="image"><a href="https://makerworld.com/en/models/144042#profileId-156624" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-01-29_1f9887d1aa63b.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/144042#profileId-156624" rel="nofollow noopener">Pokemon Keychain Pack #2</a></td><td style="border: 1px solid rgb(191, 191, 191); padding: 0.4em"><figure class="image"><a href="https://makerworld.com/en/models/128878#profileId-139600" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000197958/design/2024-01-29_c6b1251ef82d6.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/128878#profileId-139600" rel="nofollow noopener">Undertale Keychain &amp; Wall Art Pack</a></td></tr></tbody></table></figure>

Nintendo Classics Keychain Pack

Nintendo 

Dr Operator

UPDATE 03/06/24: After checking the little box of accessories that came with my printer, I notice that the  two screws they give you for the scrapper are the same size screws that I used, so if you haven't printed the scrapper, you could just use those two screws.&nbsp;I like to challenge myself to do new things, test my CAD skills and hopefully learn a thing or two along the way. So when I was browsing Amazon and saw replacement lenses for sunglasses, I decided that I had to model frames for them. This is the end result of that challenge. The lenses can be found on Amazon by searching “Replacement Lenses for Oakley Holbrook Sunglasses”. There should be a few dozen listings. I paid $16 Cdn for mine. The screws used for the arms are the spare screws left over from my “Engine Model Components Kit” that came with my printer. The Engine Model kit page lists the type of screw as “Screw BT2-6”.

Sunglasses

Just Cool

xuhao3e8

Here shows my own design, the Aurora, or 极光. It's an incredibly cool FPV cruiser that offers high speed and agility.<img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-18_07413e4f4b99.png">The design of Aurora is inspired by the IJN J7W Shinden and XP-55, with the addition of modern aircraft elements.Including full-span canard, strakes (although they serve mostly as decorative elements), and winglets.It comes with a <a target="_blank" href="https://www.printables.com/model/567442-dji-o3-air-unit-ptz" rel="nofollow noopener">servo gimbal (included in this model, remix from FLY_101</a>) and cooling system for the DJI O3. So great if you wish to use a headtracker on it.&nbsp;The flying speed is fast, with a cruising speed of 70kph (20m/s), and it can easily reach 100-130kph, pulling 3-4g maneuvers. A large area is required for flying, and it is completely unsuitable for park flying. When the flying speed exceeds 100kph, noticeable vibrations occur in the gimbal, severely affecting the flying experience, necessitating targeted optimization in the design. Here are some basic details:<ul><li>Wing Span: 1030mm</li><li>Weight (4s 18650, no gimbal & FPV system): ~1000g</li><li>Weight (with 4s18650 battery, with gimbal & FPV system): 1170g</li><li>Estimated endurance time: 30-45 minutes (theoretically, still testing)</li><li>Cruising speed: 20m/s-30m/s, 70km/h to 110km/h</li></ul>Tested avionics:<ul><li>Flight Controller: SpeedBee F405 Wing with BZ182 GPS.</li><li>ESC: Any 30A ESC is OK</li><li>FPV system: DJI O3</li><li>Servo: Kingmax KM0940MD*4 (for flight control), and GDW DS014MG*2, 280deg/180deg (for servo gimbal)</li><li>Motor: SunnySky X2216 KV1400</li><li>Propeller: APC/Gemfan 8*6-9*6, this may push you to 100kph or faster.</li><li>Battery: Sony VTC6 18650 4s1p</li></ul>Extra components:<ul><li>Carbon fiber pole:<ul><li>2*6x4x550</li><li>1*6x4x585</li><li>1*6x4x935</li><li>3*3x250</li><li>1*3x150</li></ul></li></ul>Four 6mm (diameter) x3mm (height) magnets for battery and flight controller canopy.&nbsp;The core design concept of Aurora includes:<ul><li>Appealing aesthetics</li><li>Decent endurance time</li><li>Relatively high speed.</li></ul><h2>Printing</h2><h3>Suggest print material:</h3>Fusrock/Bambu PLA Aero.I use Bambu PLA-Aero white for Wing, and FuskRock Gray PLA Aero for Fuselage. Use PLA-Aero from two manufacturer just because colors.<h3>BE CAREFUL GO SETUP CORRECT PRINTING SETTINGS FOR FILAMENTS!</h3>Default setting is for PLA-Aero, change it according to your own filaments. Strongly suggest print Aurora with PLA-Aero.<h3>3D printer</h3>Tested on Bambu Lab X1CC, suggest Bambu Machines with size=256mm<h2>Print profiles:</h2>Fuselage, wings and extra component are placed in different print profiles. They have different slice settings.<h2>Flying Video:</h2>(Click to watch if you see video unavailable)<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=-W8qLUvWbIY"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/-W8qLUvWbIY" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>对于中文用户，可以观看bilibili和简介中的介绍:<figure class="media"><div data-oembed-url="https://www.bilibili.com/video/BV1xj411W7ry/"><div class="ck-media__wrapper" data-oembed-url="https://player.bilibili.com/player.html?bvid=BV1xj411W7ry&autoplay=0&poster=1"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://player.bilibili.com/player.html?bvid=BV1xj411W7ry&autoplay=0&poster=1" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure>&nbsp;Gimbal system of Aurora is remix from <a target="_blank" href="https://www.thingiverse.com/thing:6193480" rel="nofollow noopener">https://www.thingiverse.com/thing:6193480</a> by <a target="_blank" href="https://www.thingiverse.com/FLY_101" rel="nofollow noopener">FLY_101</a>.You may also use <a target="_blank" href="https://www.printables.com/model/265534-dji-2-dof-gimbal-for-air-unit-camera/files" rel="nofollow noopener">this gimbal on Aurora</a>&nbsp;<h2>Center of Gravity</h2>Flight with current CG setup (the CG icon) is too stable. You may try the following CG at read line, this is optimal CG point according to my latest CFD results and flight test.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-28_43baa86270ef2.png"></figure>&nbsp;<h2>Donation to help me!</h2>Testing and releasing these model aircraft designs is neither easy nor cheap. It requires a significant investment of time and effort. The development cost of this airplane exceeds $1500, and that's not even taking into account my time. If you find my designs practical and useful, please consider making a donation to support my work. Your contributions will greatly assist me in continuing to develop these model aircraft, feel free to buy me a coffee by clicking follow button.<a target="_blank" href="https://www.buymeacoffee.com/xuhao3e8" rel="nofollow noopener"><img src="https://cdn.buymeacoffee.com/buttons/v2/default-yellow.png" alt="Buy Me A Coffee"></a>测试和发布航模并不便宜，这架飞机的开发成本超过万元，并且会花费非常多的时间和精力，如果你觉得我的设计非常实用，请捐款支持我，这将对我能够继续开发航模产生很大的帮助：<figure class="image image_resized" style="width:37.04%;"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-27_0ec676d5a355f.jpg"></figure><h2>Build Logs</h2>Build logs (in Chinese) for Aurora is available on <a target="_blank" href="https://xuhao1.notion.site/Aurora-1100-8851f194908a4648b1bb22ffa9a7a9cb?pvs=4" rel="nofollow noopener">my notion site,</a> this contains every detail you may want to know about Aurora.<h2>Update since upload</h2>2023/12/21: Update to integrated vertical tail and rudder: do not need manually install hinge. I put the old design of vertial tail in supported files.2023/12/23: Missing fuselage part is added to fuselage.3MF. Servo gimbal is also added to extras.3MF with original author's approval.<h2>Some details</h2>More details will be adding later.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-18_f29fd3e4a7b4a.png"></figure><figure class="image image_resized" style="width:58.84%;"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-22_d5a12ad1a93b4.jpg"></figure><figure class="image image_resized" style="width:56.85%;"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-18_3cd4e9ee5e9cc.jpeg"></figure><figure class="image image_resized" style="width:62.08%;"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-18_b01c294f7d8c7.png"></figure><figure class="image image_resized" style="width:53.14%;"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-18_12f6f67c86d8d.jpeg"></figure><figure class="image image_resized" style="width:54.3%;"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-18_d359d7203dc83.png"></figure><figure class="image image_resized" style="width:55.2%;"><img src="https://makerworld.bblmw.com/makerworld/draft/352540/2023-12-18_f582829daf851.png"></figure>

Aurora: Fixed-Wing FPV Cruiser

RC Stuff

Sakul

Revolutionize your workspace with these Brick Stackable Desk Boxes – where playfulness meets productivity! 🧱✨ Unleash your creativity and tidy up your desk simultaneously with these 5:1 Brick brick-inspired organizers. Available in 2x2 and 2x4 sizes, each Box comes complete with a built-in drawer for seamless storage of your office essentials. These bricks are not only five times the size of regular clamping Bricks but are also stackable, just like the iconic building blocks.Mix and match to create your personalized desk masterpiece! Elevate your organizational game and bring a touch of childhood nostalgia to your workspace. The Brick Stackable Desk Boxes – because work can be both efficient and fun!  If you like my work and want to support me in creating more free original designs, I would very much appreciate it if you <a target="_blank" href="https://ko-fi.com/sakul" rel="nofollow noopener">“buy me a coffee”.</a>&nbsp;&nbsp;Check out my newest Uploads <figure class="table" style="width: 98.39%"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image"><a href="https://makerworld.com/en/models/484385#profileId-396742" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000139300/design/2024-06-04_fa3ccc46fa531.jpg"></a><figcaption>🍦Pop &amp; Catch Toys Ice Cream Cone🍦</figcaption></figure></td><td><figure class="image"><a href="https://makerworld.com/en/models/447981#profileId-354736" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000139300/design/2024-05-01_5c7d04a643a0d.jpg"></a><figcaption>🐷Minecraft Animal Farm Pack🐮</figcaption></figure></td></tr></tbody></table></figure>

Brick Stackable Desk Boxes

Kids

PPZ416

Chessboard Set NO GLUE required!*square pieces are TIGHT fit*&nbsp;Prints required:1 x board (includes two parts)64 x board pieces (32 in each color)32 x chess pieces (16 in each color)1 x Lock (same color as the board)2 x border (1 in each color)&nbsp;Extra part:2mm x 20cm steel rod&nbsp;Supports (optional):Normal Support for the main board&nbsp;&nbsp;

Chessboard Set

Games

TripleGWorkshop

No spring action but overall works the same.

Vice Grips

Tools

This build is 100% printed parts that snap and screw together. The more weight you add on top, the stronger those pieces bind together.Updated 2/28/23<ul><li>Added new Screw-in adjustable feet & legs with a flat bottom by request.</li></ul>Updated 11/08<ul><li>Added new stacking corners & legs so you can make double lack stacks.</li></ul>Updated 10/28<ul><li>Added new Leg-to-Tabletop bolts that will line up perfectly.</li></ul>Updated 10/21 <ul><li>Added Mini Lack Remix - A 38% scale Lack to make if you can't do full size.</li></ul>Time and material estimates in comments. Makers Note: The threads have a slight recess around them that requires bed support 2mm tall when printing the legs vertically. Added a 3mf file for it.<figure class="image image-style-align-center image_resized" style="width:58.02%;"><img src="https://makerworld.bblmw.com/makerworld/draft/123611/2023-10-27_covzhrqrghl1.png"></figure>Credit to <a href="https://www.tiktok.com/@quality3d.io" rel="nofollow">https://www.tiktok.com/@quality3d.io</a> for the build<a href="https://www.tiktok.com/@quality3d.io/video/7155767714391313707" rel="nofollow">https://www.tiktok.com/@quality3d.io/video/7155767714391313707</a><figure class="image image_resized" style="width:63.18%;"><img src="https://makerworld.bblmw.com/makerworld/draft/123611/2023-10-27_98uwhk5czd90.jpg"></figure><figure class="image image_resized" style="width:73.78%;"><img src="https://makerworld.bblmw.com/makerworld/draft/123611/2023-10-27_n3szoo4hr24l.png"></figure><figure class="image image_resized" style="width:64.27%;"><img src="https://makerworld.bblmw.com/makerworld/draft/123611/2023-10-27_t0w6o1v3hs79.png"></figure>

Print-your-own Ikea Lack

Home

3 different styles of Fibonacci spiral trees driven by simple formulas from nature. Solid or vase mode. No Supports.&nbsp;Designed to be printed without supports<figure class="image image_resized" style="width:48.26%;"><img src="https://media.printables.com/media/prints/334911/rich_content/0a204ac4-bc39-4675-9424-3938b1cbcac6/thumbs/cover/800x611/jpg/2022-12-08-072310.webp"></figure><h2><a target="_blank" href="https://makerworld.com/en/models/54604#profileId-57227" rel="nofollow noopener">New Version HERE</a></h2><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/150500/2023-11-06_4cd5a1ba00a1f.png"></figure>

Fibonacci Spiral Trees 🟊 No Supports

Holidays

mcgybeer

Pumpkin Spinner!Print in place, easy and quick to print. A cool seasonal fidget to enjoy during Halloween.&nbsp;<figure class="media"><div data-oembed-url="https://youtube.com/shorts/1O0_qQfCCwk"><div class="ck-media__wrapper" data-oembed-url="https://www.youtube.com/watch?v=1O0_qQfCCwk"> <div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"> <iframe src="https://www.youtube.com/embed/1O0_qQfCCwk" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="encrypted-media" allowfullscreen=""></iframe> </div> </div></div></figure>&nbsp;Tip: If you feel it too tight or too loose, or even if you want to scale them, you can play with the XY compensation in the slicer to get the right tolerances.&nbsp;Check here for <a target="_blank" href="https://www.mcgybeer.xyz/commercial-license" rel="nofollow noopener">Commercial License</a>

Pumpkin Spinner

Toys

squinn

A portable cable organizer which is setup as an easy print-in-place and includes a knob on the side for conveniently winding up the cable when you're ready to pack it away.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/76375/2023-09-13_fd01d80e216de.gif"></figure>This model is an easy print that requires no supports, and three different sizes are provided to accommodate cables of different lengths. If you're not sure which to choose, I'd recommend starting with the “medium” size.&nbsp;After printing, you'll want to place the cable within the groove at its halfway point, close the lid (which is intentionally designed to close tightly), wind up the cord clockwise using the handle, and then extend by simply grabbing the cable by both ends.&nbsp;Update 2023-09-13:&nbsp;Alternative smooth-sided versions of all three sizes have now been added, and also the handle design was slightly adjusted to add a small fillet and chamfer to decrease the bridge distance. Here's a close-up picture of the updated handle on the knurled and smooth-sided versions:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/76375/2023-09-13_e75ea621224d08.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/76375/2023-09-13_68f2b35a6774b8.jpg"></figure>&nbsp;

Portable Cable Organizer / Winder

Office

3DPODesigns

<a target="_blank" href="https://makerworld.com/en/models/83371#profileId-88961" rel="nofollow noopener">New Years Mason Jar</a> now available!&nbsp;New <a target="_blank" href="https://makerworld.com/en/models/64691#profileId-67894" rel="nofollow noopener">Snowman Jar</a> and <a target="_blank" href="https://makerworld.com/en/models/55668#profileId-57243" rel="nofollow noopener">Christmas Edition</a> now available!&nbsp;UPDATE: Due to the overwhelmingly positive feedback and support from the community, I've decided to create a “short” variant of this mason jar. It prints exactly the same and uses the same lid! If you feel like mixing and matching, check it out <a target="_blank" href="https://makerworld.com/en/models/46079#profileId-47875" rel="nofollow noopener">here!</a>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/46079#profileId-47875" rel="nofollow noopener">Short</a> version measures 92mm tall without the lid, tall version measures 120mm tall without the lid.~&nbsp;A simple, elegant mason jar that prints in vase mode (can also be printed regularly). The lid does NOT print in vase mode, so I've uploaded two separate profiles for your convenience.&nbsp;Vase mode profile is set to .8 wall thickness for strength.&nbsp;Please note the seam for the lid is set to “back” as I prefer to be able to hide them as best I can on cylindrical items. If you prefer other seam placement please adjust.&nbsp;If you enjoy the model, please toss it a like!

Mason Jar with Lid (Vase Mode)

Kitchen

DreamStarter

The bust of the classic RX-78-2 Gundam in my interpretation. Have fun printing and painting!&nbsp;If you like this model check out my other models here:<a target="_blank" href="https://cults3d.com/en/users/DreamStarter/3d-models" rel="nofollow noopener">https://cults3d.com/en/users/DreamStarter/3d-models</a>

GUNDAM BUST

Busts

3DDruck_Obi

Print with 100% infill 0,2mm layer height or lessUse Bambu height modyfier to colorize this model

Marvel Logo Multicolor

3D painting

BC Designs

Mounting the external spool on the side for easier access, with added filament guide for smooth operation. &nbsp;&nbsp;Parts<ul><li>2 x 608ZZ bearings</li><li>1 x PC4-M10 Pneumatic Connector (optional, included filament arm for PTFE tubing for those without)</li><li>1 x m3 x 14mm or 16mm for the top screw hole (start with the smaller one first as can bottom out and get stuck easily).</li><li>2 x m3 x 18mm for the bottom screw holes.</li></ul>Connector: <a target="_blank" href="https://www.amazon.co.uk/gp/product/B0966XQ4C4/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1" rel="nofollow noopener">https://www.amazon.co.uk/gp/product/B0966XQ4C4/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1</a>&nbsp;Choose either the 3mf file with the PC4-M10 fitting, or the one with PTFE passthrough.&nbsp;Included 3mf file setup as follows:<ul><li>0.20 layer height @ 50% infil, I recommend PLA+</li><li>4 walls</li><li>4 top and bottom layers</li><li>Supports</li><li>Spool on 2nd build plate as I think the model looks better in 2 colours :)</li><li>Both filament arms included on build plate, remove the one you dont want.</li></ul>&nbsp;Assembly<ol><li>Spend a few minutes carefully removing the supports from the inner slots </li><li>Screw on the pneumatic connector to the filament guide and inert some bowden tubing. The PC4-M10s allow the tubing to pass through.</li><li>Screw to side of case using the top back case screw hole and the 2 original screw holes.</li><li>Slide on spool holder. </li><li>Slide on filament arm.</li><li>Detatch when not in use or leave as is.</li></ol>