Astro

SavageLau

<h3>If you want a commercial license, check out my bio and get it from Patreon.</h3>&nbsp;<h4>Hey guys, this is another design for Makerworld dragon year contest (4/5). Loong wand, Loong also known as oriental dragon, or Chinese dragon. I think it would be a great gift/toy for kids for New year.</h4><h3>Best wishes to you all! 新年快乐.</h3>&nbsp;This Loong wand design takes 47g of filament and 2h40m printing time.I try to keep all my wands design consistent, similar printing hours, material cost, etc.&nbsp;&nbsp;This is a complete redesign from the last dragon wand. It took me more than 20h of continues work to get the initial design done. And 10+ hours of revisions. Yep, this wasn’t included in my test print hours. Be sure you like this model 😊 Want more wand? Let me know in the comments.&nbsp;<h2>Revisions:</h2>Update 1/26/2024: 3.x.1 Horn fit and finish issue. (tested) New update improved the fit for horn on profile: v3.5 Large, v3.3 Basic, v3.4 Flame. Suggest not to use some of the weak silk filaments. It is small parts, will easy to break with snap fit tolerance. &nbsp;<h2>Printing options:</h2>I made a few different styles for this design. “Plain” is Loong without horn. “Basic” is Loong with removeable horn. “Flame” is added flame on Basic model. “Large” is only available for P, X, &A1. Since the height of the model is too large for a1mini.I personally like the Large size the most. The larger size really brings a different feeling to this design. You will feel more of imposing of a Loong.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/456325/2024-01-16_e08d19c6e1cfd.png"></figure>&nbsp;&nbsp;<h3>If you like other wand design:</h3>Dragon wand:<a target="_blank" href="https://makerworld.com/en/models/135043#profileId-146518" rel="nofollow noopener">https://makerworld.com/en/models/135043#profileId-146518</a><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/456325/2024-01-16_d56c3cbaa1e49.jpg"></figure>&nbsp;Harry Potter wand:<a target="_blank" href="https://makerworld.com/en/models/68778#profileId-72937" rel="nofollow noopener">https://makerworld.com/en/models/68778#profileId-72937</a><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/456325/2024-01-16_26bcefd5022d.jpg"></figure>&nbsp;<h2> </h2><h2>Printing Suggestions:</h2>If you are printing on a1mini/a1 with cold room temperature (consider it is winter now) increase your bed temperature to 80C. To reduce possible fail rate.If you are printing with P & X Series, you could close the door to keep a consistent ambient temperature.Printing profile I uploaded have sightly thicker first layer, it is due to the small parameter on first layer, it will ensure your first layer stick good on build plate.This design has bigger parameters than my other wand design, print without brim is still not recommended but highly doable. Try at your own risk.&nbsp;Don't use some of the silk and weak filaments: <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/456325/2024-01-16_ac98214f72e76.png"></figure><h2>Post work:</h2><h3>clear brim:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/456325/2024-01-16_0b36a23125eca.gif"></figure><h3>install horn:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/456325/2024-01-16_23eebab9bacf.gif"></figure><h2> </h2><h2>Design:</h2>The design isn’t perfect, I decided to sacrifice some “style” for better “printability”.I originally wanted to design a dragon holding a ball. So, the retractable parts will be dragon body and tail. That said, the orientation of the model will be completely different from my last dragon design.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/456325/2024-01-16_bc8842b333e3c.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/456325/2024-01-16_80a09a8bbb86b.png"></figure>But I have changed my mind during the design. I want to make retractable parts come out from dragon mouth.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/456325/2024-01-16_f9b3f5edf311.png"></figure>So, I started with the overall style, since I want it to be more of Oriental dragon style. A lot more details have been added to the model.I didn’t think my new dragon scale design was over complicated, it keeps my software crashing. I think it is also because the entire model’s mesh has over 1 million triangles. Since my intension was getting something very refined done, this was probably a bit overdone.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/456325/2024-01-16_0153da89875bc.png"></figure>&nbsp;The initial v2 had a few design revisions. I realized the dragon beard and horn are a bit tricky to print. The beard is a bit too small and causes printing issues, and I didn’t really like to have support on this model.&nbsp;So, model improvements took place again. I have also decided to make horn removable, that way you can print without support and print it with the color you like.The retractable mechanism is also refined. Bottom layer otter edge is clear for earlier post work. (remove brim)<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/456325/2024-01-16_72d75fc68d641.png"></figure>&nbsp;&nbsp;Old Revisions:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/456325/2024-01-16_120cb9c9d7592.jpg"></figure>&nbsp;

Loong Wand (Retractable) v3 Series

Onnozelheid

cm3dshop.de

Poop Chute with Tray and hidden Handle&nbsp;Easy acess to the Poop with a pull out tray (if you got low space behind and besides the printer)&nbsp;stays in place with 5 round Magnets (attached to the printer) d=6mm ; thickness 4mm (3mm will also work when not pushed all the way in)&nbsp;tray can be hold closed with 4 magnets (Attention at the polarity!) …just optional&nbsp;hidden handle with Bambu Logo for pull out the tray : flat with front when closed ; for opening push the top part in and then pull at the lower part…very simple and easy…fully printed&nbsp;optional Lid for "clean design"&nbsp;&nbsp;Added a version for Users with a 40mm Stone plate under the printer.. So there is additional space for the Poop. ;)<a target="_blank" href="https://makerworld.com/en/models/79531#profileId-84152" rel="nofollow noopener">https://makerworld.com/en/models/79531#profileId-84152</a>&nbsp;At All it is a bit over engineered … but…does it really matter?! ;)&nbsp;Just let me know in comments when you have suggestions for improvement.&nbsp;ATTENTION: the print profile uses the PETG/PLA trick to get a super smooth interface between the Tray and the supports!&nbsp;&nbsp;

Poop Chute Tray with hidden handle+Lid

Utilities

Sakul

&nbsp;Brighten up your office breaks with this fun mini table foosball game.A fully functional table soccer set to challenge your colleagues. All you need, aside from the printed parts, are 20 M3x10 and 12 M3x20 screws, and some CA Glue. For assembly, print out all the parts, and start by gluing the playfield into the base. Screw the legs and the ball catchers to the base; you can screw them directly into the plastic, as it will be plenty strong. <figure class="image image_resized" style="width: 61.55%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000152653/design/2024-01-22_6c8651f7c1e8.jpg"></figure> Glue the side caps into the base, slide the rods in from the side, and also stick the figurines on the rods. The figurines will be fixed in place using the M3x10 screws. All the TPU parts can now be attached using CA Glue. Glue the handles and end caps on the rods, also attach the TPU feet to the legs. The ball is made by gluing the two halves together.<figure class="image image_resized" style="width: 34.44%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000152653/design/2024-01-22_3727bab3bdd4.jpg"></figure>Lastly, slide the goal indicator over the display shield and then attach it to the base. Have fun playing!  If you like my work and want to support me in creating more free original designs, I would very much appreciate it if you <a target="_blank" href="https://ko-fi.com/sakul" rel="nofollow noopener">“buy me a coffee”.</a>  Check out my newest Uploads: <figure class="table" style="width: 98.39%"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image"><a href="https://makerworld.com/en/models/484385#profileId-396742" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000152653/design/2024-06-04_09fc049f7c6e.jpg"></a><figcaption>🍦Pop &amp; Catch Toys Ice Cream Cone🍦</figcaption></figure></td><td><figure class="image"><a href="https://makerworld.com/en/models/447981#profileId-354736" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000152653/design/2024-05-01_6d8b75eefb4a4.jpg"></a><figcaption>🐷Minecraft Animal Farm Pack🐮</figcaption></figure></td></tr></tbody></table></figure>

Onnozelheid

Utilities

Games