AquaHaven

gwhitt856

Aquarium cave for corner of tank. Recommend it be printed in petg. If you use too little infill it may float. Sized at 4"x2"x2". Scale to fit your needs.

Aquarium Corner Cave

Fish tank

DGA3DP

Simple model of Easter basket. Printed from orange Rosa3d Pet-g. Material: Pet-g recommended ( PLA, ASA, ABS etc.)Layer high: 0,2mm ( 0,3mm possible to print)Support needed

Easter basket

Easter

JamesThePrinter

** Get an early start! Get the <a target="_blank" href="https://makerworld.com/en/models/41177" rel="nofollow noopener">Christmas version</a> now! **&nbsp;&nbsp;Light up different Halloween scenes in this display. A tea light candle is required. The display features a door that opens to allow access to the tea light. Use a section of 1.75mm filament inside the hinge to connect the door to the case. Depending on your printer/setup, this hole may be on the tight side or a bit loose. If tight, drilling out the hole may help. If it is slightly oversized, I suggest melting the end of the filament piece with a soldering iron or lighter.I have included a separate liner. This allows you to print the case in a dark color, but line the inside with a lighter color to allow for more reflection of light outward, making everything brighter.For a complete display, you will need:<ul><li>1x Case</li><li>1x Door</li><li>1x Knob</li><li>1x Snap Ring</li><li>1x Liner - Optional</li><li>1x (minimum) Scene - You can easily remove the snap ring to swap out scenes as desired</li></ul>Check out my other holiday models <a target="_blank" href="https://makerworld.com/en/u/1360890085/collections/23941" rel="nofollow noopener">here</a>.<h4>Print Settings</h4>No special setting are needed for the display case, door, knob, snap ring and liner. &nbsp;Scenes Print SettingsPrint the scenes with 100% infill. The scenes also require color changes:<ul><li>The top 2 layers should be black</li><li>If there is no moon in the scene, all other layers can be white or clear - both look nice</li><li>If there is a moon in the scene, it will look best if the bottom 2 layers are printed in clear filament<ul><li>All other layers should be white</li><li>All non-black layers could be printed in all white or all clear if one isn't available to you</li></ul></li></ul>&nbsp;<h4>Assembly</h4>Glue the knob into the door. Only a very small amount is needed.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_njhnxlluv3as.png"></figure>Put the door in place and latch it. Use a 20mm piece of 1.75mm filament to connect the 3 sections of the hinge. If the filament goes in very easily, it may be a good idea to heat up the top end of the filament ‘pin’ and press it flat. This will prevent the pin from falling through later on.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_ps9jc73zrxio.png"></figure>Open the door. Insert a scene into the opening (image facing outward). Insert the snap ring behind the scene by gently squeezing and placing it into the groove (see red arrow below).<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_zosx4sj7pb0v.png"></figure>If you are using a liner, slide it inside the case. This may be a tight fit. Go slowly and be sure to slide it in evenly on all sides.<figure class="image image_resized image-style-align-center" style="width:75%;"><img src="https://makerworld.bblmw.com/makerworld/draft/90743/2023-09-14_t3jeg8v9f9hv.png"></figure>Turn on your tea light and close the door.&nbsp;&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;The following filaments were used in the pictures above:<ul><li>Bambu Lab Matte Charcoal PLA</li><li>Bambu Lab Matte Ivory White PLA</li><li>GIANTARM Transparent Clear PLA</li></ul>

Halloween Tea Light Display

Halloween

MakerWorld

This is a well-designed 4-color Lichtenstein Castle model with rich details on exteriors. It can be 3D printed in multiple colors with Bambu Lab AMS.&nbsp;Recommended filaments:Bambu PLA-CF Burgundy Red(14200)<a target="_blank" href="https://store.bambulab.com/collections/pla-1/products/pla-cf?variant=40828231516275" rel="nofollow noopener">https://store.bambulab.com/collections/pla-1/products/pla-cf?variant=40828231516275</a>Bambu PLA-CF Lava Gray(14101)<a target="_blank" href="https://store.bambulab.com/collections/pla-1/products/pla-cf?variant=40828231581811" rel="nofollow noopener">https://store.bambulab.com/collections/pla-1/products/pla-cf?variant=40828231581811</a>Bambu PLA Basic Gray(10103)<a target="_blank" href="https://store.bambulab.com/collections/pla-1/products/pla-basic-filament?variant=40909352960115" rel="nofollow noopener">https://store.bambulab.com/collections/pla-1/products/pla-basic-filament?variant=40909352960115</a>Bambu PLA Matte Dark Blue(11602)<a target="_blank" href="https://store.bambulab.com/collections/pla-1/products/pla-matte-filament?variant=40789984968819" rel="nofollow noopener">https://store.bambulab.com/collections/pla-1/products/pla-matte-filament?variant=40789984968819</a>Hotend: 0.4mm Hardened SteelPrint time: 24.3h

Lichtenstein Castle

To Print

cwills75

Update There are now four sets of badges that can be printed. The set you want will depend on your AMS Lite orientation. If you are using it on the stock stand or mounted on a wall in the normal position, you will want the “Normal Orientation Badges”. If you are mounting your AMS Lite Upside down or left/right facing, choose one of the other three sets. If in doubt, look at how your AMS Lite is or will be mounted, especially taking note of the small triangular arrows and how you want the numbers rotated, then look at the preview pictures in the print profiles. You can also load them in a slicer and look at them from UNDERNEATH the build plate, as they print face-down. That should help.&nbsp;I felt the A1 Mini's AMS Lite filament slot numbers were hard to read, so I made up these badges to push-fit over the top of them. They are pre-colored, and you can use whatever colors you like to customize yours. If somebody wants a different specific font, and it is freely available for me to download, you can request a specific one and I'll add it.&nbsp;Remember to check your flushing volumes before printing, and as the text is face-down on the build plate, you can customize what color prints first in your plate settings (the little gear next to the build plate in the slicer). The wall mount in the pictures above is available here if interested: <a target="_blank" href="https://makerworld.com/en/models/48945#profileId-50873" rel="nofollow noopener">https://makerworld.com/en/models/48945#profileId-50873</a>&nbsp;

Bambu A1/Mini AMS Lite Slot Number Badges

A1 mods

Bambu Lab

This seasonal model has 113 parts, and by default prints in 6 colors that lay down on 9 separate plates. Once upon a time, a project of such scale demanded a certain amount of courage to start preparing and slicing, let alone print it. Now, with Bambu Lab's hardware and software, you can finish the print within two days and customize the colors to your liking. You can even customize the text and the logo!&nbsp;In the Assembly view mode, you can simply choose a part and press the number of the filament to color that part. We left blank plate in the model so you can type in your own text.<figure class="media"><div data-oembed-url="https://www.youtube.com/watch?v=88gXxk9oWPg&t=29s"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/88gXxk9oWPg?start=29" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>