Alko_07

3DFarmer

HiI created MY HERO ACADEMIA multicolor logo for Funko Pop Collection.Made by changing colors at high during printing.0-13.8 mm -BLACK14 -18.8mm - RED19 - end - YEALLOW&nbsp;Support : noInfil: 15%Lines: 2Layer: 0.2Brim: Yes

MY HERO ACADEMIA LOGO FUNKO POP

Anime

buskin

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmFilaments Used: PLA+ Sunlu Black Transmission Distance: 0.6 PLA+ Sunlu Grey Transmission Distance: 2 PLA+ Esun Bone White Transmission Distance: 5 PLA+ Sunlu White Transmission Distance: 5Swap Instructions: Start with Black At layer #32 (2.64mm) swap to Grey At layer #34 (2.8mm) swap to Bone White At layer #40 (3.28mm) swap to White for the rest.

Hueforge Death Note Coaster Set With Holder 

Untersetzer/Coaster

Jaysiro_07

Echo Holder

Wohnzimmer

The Dragons Den

Crested Gecko was test printed down to 50%. &nbsp;10% infill3 to 4 lines .1 or .2 height No support Print in place. Print with raft or brim if doesn't stick.&nbsp;Please feel free to post pics of your makes. I would love to see them. &nbsp;If you would like to sell the prints join us on Tribes or Patreon for a seller's permit. &nbsp;Copyright:All The Dragons Dens designs are protected by the Copyright Law. By purchasing, you do not have the right to sell any digital files or printed models.The Digital files are never to be re-sold, shared, or given away.&nbsp;To legally sell the printed models, you can get my permission by joining our community- <a target="_blank" href="http://patreon.com/TheDragonsDen411" rel="nofollow noopener">patreon.com/TheDragonsDen411</a>&nbsp;You can join The Dragon's Den Discord to exchange with me and the community. <a target="_blank" href="http://discord.gg/k2KFnXNuBV" rel="nofollow noopener">discord.gg/k2KFnXNuBV</a>

Crested Gecko

flexi Toys

angry-p1p

Have fun with this Nintendo Switch Dock Cover. This cover is for the “normal” Switch Dock, I don't know if the OLED-Dock is different.&nbsp;If your printer and filament is dialed in it should slide right over your dock.&nbsp;To ensure you waste as little filament and time as possible I added a small test piece on a second plate. If needed adjust/scale it by a tiny amount according to your tolerances or filament.&nbsp;All my prints use Sunlu PLA +. A first layer and first layer infill speed of 25mm/s, only one wall on first layer and a first layer line width of 0.5mm at a nozzle size of 0.4mm.&nbsp;See my other designs:&nbsp;0.2mm Nozzle<figure class="image"><a href="https://makerworld.com/en/models/142951" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/413033/2024-01-15_7579e08fc1604.jpg"></a></figure>&nbsp;0.4mm Nozzle<figure class="image"><a href="https://makerworld.com/en/models/142960" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/413033/2024-01-15_776556333bd3d.jpg"></a></figure>&nbsp;&nbsp;

Nintendo Switch Dock Cover Charmander

Switch

AU3D

Set of 81 sizes of IKEA Skadis pegboards. To enhance user convenience, I&#39;ve organized the files and print profiles based on the number of columns. The board are prepared for M4 countersunk screws (M3.5 will work as well, M3 probably too, but not tested). Each board comes equipped with an integrated 10mm standoff. For installation on wood, I recommend using screws that are 30mm+ in length, and for wall mounting, opt for screws that are 40mm or more are recommended, depending on your particular needs.&nbsp;Caution: The 10mm variants have a reduced length compared to the original mounting mechanism. To ensure the boards align seamlessly with an original Skadis Board, opt for the <a target="_blank" href="https://makerworld.com/en/models/419292" rel="nofollow noopener">20mm variant</a> or utilize <a target="_blank" href="https://makerworld.com/en/models/418809" rel="nofollow noopener">Boards without integrated Spacers</a> and print the <a target="_blank" href="https://makerworld.com/en/models/418874" rel="nofollow noopener">spacers</a> separately.<h3>Skadis Collection</h3>I am constantly developing more IKEA Skadis attachments. Check out my<ul><li><a target="_blank" href="https://makerworld.com/en/u/2942852598/collections/453266" rel="nofollow noopener">IKEA Skadis Shelves, Trays and Container Collection</a></li><li><a target="_blank" href="https://makerworld.com/en/u/2942852598/collections/188108" rel="nofollow noopener">General IKEA Skadis Collection</a></li><li><a target="_blank" href="https://makerworld.com/en/@AU3D/collections/1044616" rel="nofollow noopener">IKEA SKADIS Boards Collection</a></li></ul>

IKEA Skadis with Standoff (10mm)

IKEA Skadis

RoB.G