AbeFM1

T_WITHE

Welcome! I am pleased to share with you the Gardena quick connector set that I designed in various sizes to perfectly meet different connection needs. The set is available with different threads and sizes:<ul><li>External and internal threads</li><li>Sizes: 3/8&#34;, 1/2&#34;, 3/4&#34;, 1&#34; (M18)</li><li>Traditional BSP thread</li></ul>Material Choice For the best results and long lifespan, I recommend the following materials for printing: PETG, ASA, ABS. PLA can also be used, but I strongly recommend the former materials. Sealing Rings Sealing rings can be printed from TPU material as it is flexible and waterproof. However, for the best results, I recommend using factory sealing rings, especially O-rings, to ensure maximum water tightness and long-term reliability.It&#39;s important to note that high pressure can cause leakage or other issues, so I do not recommend using the connector at high pressure! I experienced slight leakage at 6 bar, so please don&#39;t leave negative feedback because of this. Thank you! For supports, if possible, use support material, or use PETG-PLA or PLA-PETG interface layer mode. Thank you for choosing this 3D printable Gardena quick connector set! I hope you find it useful. If you have any questions, feel free to reach out to me! If you have any suggestions or requests, please contact me. This is a revised version of my original model with some additional sizes: <a target="_blank" href="https://www.thingiverse.com/thing:4904221" rel="nofollow noopener">https://www.thingiverse.com/thing:4904221</a>

Gardena quick connector set

Garden

vier2acht

If you don&#39;t want to have a filter in the tent, you can use this holder to mount your exhaust in different positions in the tent.&nbsp;<ul><li>PLA/PETG/ABS/ASA</li><li>Infill 15-100%</li></ul>

Growbox exhaust holder

Pot Tools

wotfan

I recommend printing with a .2mm nozzle at .14mm layer height.&nbsp;The best sheet magnets I have found to use with this model is Marietta Magnetics brand 30mil (with adhesive).

Multicolor Samurai Jack Magnet

Multi-Material

DatumCAD

<figure class="image image_resized image-style-side" style="width:34.11%;"><img src="https://makerworld.bblmw.com/makerworld/draft/696022/2024-03-12_f4af98eab96a6.gif"></figure>The aim was to design a Centering tool that:<ol><li>had no need for hardware (i.e. was fully printable),</li><li>was adjustable to make it suitable for various material stock widths,</li><li>that also included a second function that would make it more versatile.</li></ol>Other similar printed tools only seem to offer the one of these functions, and a lot of those focused purely on centering are ‘fixed’ and so become cumbersome on smaller stock sizes. Those that do adjust often use metal fasteners requiring tools.&nbsp;And so this design is the result of my efforts to solve the above and make a great multipurpose tool. I hope you like it!&nbsp;***Update 12/03/2024***: Imperial version added as many have asked for this, so there are now 2 print profiles to choose from ……“Metric” & "Imperial". I have also taken the opportunity to slightly reposition the number text to better align with the notches which should avoid any confusion when using these.<figure class="image image_resized image-style-side" style="width:50.08%;"><img src="https://makerworld.bblmw.com/makerworld/draft/696022/2024-03-12_b468c9f94b7b.gif"><figcaption>Centre Marking GIF</figcaption></figure>&nbsp;&nbsp;Function #1 - Centre Marking:&nbsp;The two knurled shoulder bolts (yep - fully 3D printable) can be screwed into whichever pair of holes best suits the width of material (Note: when spaced at the furthest setting the tool can span a width of 125mm max).&nbsp;Its then a simple case of sliding the tool along the length of the material with one shoulder bolt over each edge. Tip: apply a slight twisting force to keep the shoulder bolts ‘pinned’ against the sides while you do so.&nbsp;A pencil / pen can be used to mark through the conical hole, located centrally on the tool, which will prevent your line from wandering out of position. See animation.&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;<figure class="image image_resized image-style-side" style="width:50.04%;"><img src="https://makerworld.bblmw.com/makerworld/draft/696022/2024-03-12_fd61218b72569.gif"><figcaption>Edge Marking GIF</figcaption></figure>Function #2 - Edge Offset Marking:&nbsp;So this tool also incorporates stepped notches from 5-25mm (at 5mm increments). Allows quick marking out / scribing of measurements in from the edge of your material. This is really common when you are trying to quickly position fixings / pilot drill hole locations etc. See animation.&nbsp;&nbsp;Perfect for the home, studio, workshop…… Just print, assemble & put to use!&nbsp;I love designing for 3D printing, please take a look at all my other models which are all free (and will always continue to be)… if you value any of the downloads enough & are able to support me, then please consider buying me a coffee to keep me going! <a target="_blank" href="https://www.buymeacoffee.com/DatumCAD" rel="nofollow noopener">www.buymeacoffee.com/DatumCAD</a>&nbsp;

2-in-1 Centre Marking Tool

Tools

christofer.jh

The one ring, need I say more?&nbsp;Hang on the wall or just put it on a table. The ring is a whole 160mm in diameter!&nbsp;I printed with Bambu PLA silk - Gold.&nbsp;<h2>Current version 2.0 - Now better shine!</h2>Warning, the new back plate is much more secured when inserted. Make sure led is installed before closing.&nbsp;The assembly is easy, just take about 50cm led strip and put it in the ring, like this:<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163169/design/2024-02-14_9d0f0db27d1.jpg"></figure>Or alternative slide it in above the internal “bride”, this way you can get two loops for more light.&nbsp;Holder remixIf you want a stand take a look at this remix: <a target="_blank" href="https://makerworld.com/en/models/467240#profileId-376287" rel="nofollow noopener">https://makerworld.com/en/models/467240#profileId-376287</a><h3>Revisions:</h3>v 2.0Total redesign of the inner space of the ring and the back plate. The led strip is now held in place which gives a more uniform shine. Slightly bigger radius on the top of the ring.The back plate also snaps to the ring better, DON&#39;T PUT ON UNTIL LED IS INSERTED.v 1.1<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163169/design/2024-01-30_7d6ab2acdbc06.jpg"></figure><ul><li>Added a optional back plate that snaps in place. Use the chord for hanging on wall, or drill a hole for a nail (or use bambu studio and add a hole)</li></ul><figure class="image image_resized" style="width: 23.9%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163169/design/2024-01-31_2e6cf6cbfd73d.jpg"></figure><figure class="image image_resized" style="width: 24.71%"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000163169/design/2024-01-31_e9eca6e2a85f3.jpg"></figure>

The one ring - The Lord of the Rings

Furniture

Brent Peterson

<h2>Toroidal Launcher</h2>This is an original design created for the <a target="_blank" href="https://makerworld.com/en/contests/5" rel="nofollow noopener">Flying Objects design contest</a> and features a handheld three-stage planetary gearbox that launches a toroidal ring over 3000 RPM! The design is 100% 3D printed; all pieces press fit together and no additional hardware is required.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/360322/2023-12-15_92eaaa9691a14.gif"></figure>The gearbox used in this design is modular and will be released as it's own series soon™, if you have any thoughts or feedback please share so I can continue to improve the design!<h3>Modifications and Add-on Designs</h3><ul><li>[NEW!] Remix Templates<ul><li><a target="_blank" href="https://makerworld.com/en/models/123219" rel="nofollow noopener">Threaded cap</a></li><li><a target="_blank" href="https://makerworld.com/en/models/125073" rel="nofollow noopener">Hexagon gear driver</a></li></ul></li><li>Gearbox modifications<ul><li><a target="_blank" href="https://makerworld.com/en/models/99992#profileId-106623" rel="nofollow noopener">High torque conversion kit (1:2 ratio)</a></li><li><a target="_blank" href="https://makerworld.com/en/models/105586" rel="nofollow noopener">1:3 ratio gearset</a></li><li><a target="_blank" href="https://makerworld.com/en/models/108803" rel="nofollow noopener">1:4 ratio gearset</a></li><li><a target="_blank" href="https://makerworld.com/en/models/105590" rel="nofollow noopener">1:5.5 ratio gearset</a></li><li><a target="_blank" href="https://makerworld.com/en/models/110188" rel="nofollow noopener">1:7 ratio gearset</a></li></ul></li><li>Toroidal ring designs<ul><li><a target="_blank" href="https://makerworld.com/en/models/102279" rel="nofollow noopener">Toroidal Launcher Mini Rings - 100mm pitch</a></li><li><a target="_blank" href="https://makerworld.com/en/models/97633" rel="nofollow noopener">Toroidal Launcher Mini Rings - 150mm pitch</a></li><li><a target="_blank" href="https://makerworld.com/en/models/102728" rel="nofollow noopener">Toroidal Launcher Mini Rings - 200mm pitch</a></li></ul></li></ul><h3>Specifications</h3><ul><li>Three stage planetary gearbox with 1:48 gear ratio (overdrive)<ul><li>0.75mm gear module for ultra-smooth performance (24/72 teeth)</li><li>10mm hex driver for connecting gear stages</li></ul></li><li>Toroidal ring design with four blades (1.2mm thick) available in three sizes<ul><li>100mm diameter, 150mm pitch</li><li>125mm diameter, 175mm pitch</li><li>150mm diameter, 200mm pitch</li></ul></li></ul><h3>Printing tips</h3><ul><li>All prints pictured were printed using Bambu Basic and Matte PLA</li><li>For best results run flow rate calibration and thoroughly clean build plate</li><li>The launcher gears are available in two print profiles with the following changes to the standard 0.20mm profile:<ul><li>Arachne wall generator</li><li>5x top and bottom walls, 25% infill</li><li>75 m/s inner and outer wall print speed</li></ul></li><li>The toroidal rings are available as a single print profile with the following changes to the standard 0.20mm profile:<ul><li>0.6mm line thickness, Arachne wall generator</li><li>75 m/s inner and outer wall print speed</li></ul></li><li>The launcher housing prints with the standard 0.20mm profile.</li></ul><h3>Launcher Parts</h3><ul><li>Launcher Gears<ul><li>SunGear24.step [3x]</li><li>PlanetGear24.step [9x]</li><li>PlanetCarrier24.step [3x]</li><li>RingGearDouble.step [1x]</li><li>RingGearLid.step [1x]</li><li>RingDriver.step [1x]</li><li>GearDriver.step [1x]</li></ul></li><li>Launcher Housing<ul><li>HousingBase.step [1x]</li><li>HousingRingLid.step [1x]</li><li>HousingCarrierHolder.step [1x]</li><li>HousingCarrierThreads.step [1x]</li></ul></li><li>Toroidal Rings<ul><li>ToroidalRing100.step [1x]</li><li>ToroidalRing125.step [1x]</li><li>ToroidalRing150.step [1x]</li><li>ToroidalRingDriver.step [1x]</li><li>ToroidalRingLauncher.step [1x]</li></ul></li></ul><h3>Launcher Assembly (Gears + Housing)</h3><ul><li>Assembly the planet carrier with three planet gears and one sun gear as shown below. Repeat for all three planet carrier assemblies.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/360322/2023-12-31_efae722ebe2db.gif"></figure><ul><li>Use the shorter hex drive to connect two sets of gears. Align both planet carriers and hold them with one hand while holding the double ring gear in the other hand and slowly turning as you close the gear; once closed insert the assembly into the main housing to hold secure. The gears should spin freely; if they don't remove the gear assembly and repeat this step.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/360322/2023-12-31_f1371c6d57ee6.gif"></figure><ul><li>Use the longer hex drive to connect the last set of gears and then assemble with the threaded cap as shown below.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/360322/2023-12-31_4926c45fbbf51.gif"></figure><ul><li>Carefully mesh the single ring gear with the planet gears taking note of the 2mm flat section that is positioned towards the main gear assembly as shown below. Use the same method of rotating while slowly closing and covering with the cap to hold secure.</li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/360322/2023-12-31_54c6fffceb4e5.gif"></figure><ul><li>Done! The assembly should spin smoothly with the output shaft making 48 rotations for every one turn of the input knob. Performance depends on printer tolerances and filament used; for best results use the include print profiles with Bambu Studio (supports many different printers). A bit of lubricant can also be added to the gears to improve performance.</li></ul><h3>Toroidal Ring Assembly</h3><ul><li>Insert the hex drive into the interlocking driver; the clearance is tight but it should be a snug fit.</li><li>Insert the assembled driver into the output sun gear, the fit should be the same.</li><li>If the driver does not stay secured when launching the ring a small amount of CA glue can be use.</li></ul><h3>Changes</h3><ul><li>v1<ul><li>Initial release; files now available in v1old folder</li></ul></li><li>v1.1<ul><li>Updated print profiles with improved settings for gears and rings</li><li>Improved single color print profile, fits on A1 mini and objects are laid out to allow skipping</li><li>Improved clearance of gears and overall meshing</li><li>Updated toroidal ring to use the same launcher as the mini rings<ul><li>Print profile includes 3 sizes (100mm, 125mm, 150mm)</li></ul></li><li>Updated assembly instructions to have fewer steps with a GIF for each one</li></ul></li><li>v1.1.01<ul><li>Added new section for template designs intended for remixing</li></ul></li></ul>

Toroidal Launcher - High RPM launcher featuring compact planetary gearbox

Toys

Wurschtfett

<h2>Here I present a easy pressure advance calibration tool!</h2>Previously, you have to tune your flow!Then just insert the .3mf in Bambu Studio or Orca Slicer an select the Filament you want to calibrate.At last, just inspect the top layer for gaps in the corners and smoothness.For example, the “24 Block” means, you have to choose 0,024 K-Factor.&nbsp;<h3>You´re ready to go!</h3>

PA Calibration Stairs

Calibrations

TrocheHole

<figure class="table" style="width:60%;"><table class="ck-table-resized" style="background-color:#f5f5f5;border:12px solid #f5f5f5;"><colgroup><col><col></colgroup><tbody><tr><td style="padding:8px;vertical-align:top;">[ Information ]A sister model of this “Split Ring” is available on the following page.&nbsp;<a target="_blank" href="https://makerworld.com/en/models/16181" rel="nofollow noopener">“Oval Carabiner (7 sizes)”</a></td><td style="text-align:center;width:30%;"><a target="_blank" href="https://makerworld.com/en/models/16181" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/203986/2023-09-22_903g3lqlgpap.jpg"></a></td></tr></tbody></table></figure><h4> </h4><h4>2 shapes and 6 sizes each.</h4>A removable ring that is harder to use than carabiners. But I wanted something sturdier with a simple shape, so I designed this.&nbsp;<h4>2 types of data are available for each ring.</h4>[Easy-to-Print] ─ Larger tolerance. The end of the ring-line comes off easily. [Hard-to-Print] ─ Smaller tolerance. The end of the ring-line can be held in place.&nbsp;&nbsp;<h3>Print Instructions</h3>If the printed ring sticks together and does not open, try scaling up an Easy-to-Print model in a slicer app. (e.g. 120% or more) This will increase the clearance between the inner and outer rings and make it even easier to print.Brims/Rafts ─ Doesn't MatterSupports ─ No&nbsp;<h3>Post-Printing Tips</h3>Even if the inner and outer rings are stuck together after printing, it may come off if you pinch it with both hands and wriggle it.&nbsp;&nbsp;<h3>How to Use</h3>Open ─ This split ring does not open horizontally. To open it, shift the end of the outer ring-line vertically.Close ─ There are notches on both ends of the ring-line to hold them in place. Therefore, the inner end needs to be fitted first to close the ring. The outer end should be fitted last.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/203986/2023-09-22_vsdi7j2sn9hk.jpg"></figure>&nbsp;<h3>Sizes</h3>Shape No.* ─ external dimension (and width of the ring-line)Circle No.3 ─ DIA14.1 x T2.4 mm (3 mm) ─ similar in size to a fingernail Circle No.4 ─ DIA18.8 x T3.2 mm (4 mm) Circle No.5 ─ DIA23.5 x T4.0 mm (5 mm) Circle No.6 ─ DIA28.2 x T4.8 mm (6 mm) ─ similar in size to a plastic bottle cap Circle No.7 ─ DIA32.9 x T5.6 mm (7 mm) Circle No.8 ─ DIA37.6 x T6.4 mm (8 mm)Oval No.3 ─ W19.5 x L14.1 x T2.4 mm (3 mm) ─ similar in size to a fingernail Oval No.4 ─ W26.0 x L18.8 x T3.2 mm (4 mm) Oval No.5 ─ W32.5 x L23.5 x T4.0 mm (5 mm) ─ similar in size to an SD card Oval No.6 ─ W39.0 x L28.2 x T4.8 mm (6 mm) Oval No.7 ─ W45.5 x L32.9 x T5.6 mm (7 mm) Oval No.8 ─ W52.0 x L37.6 x T6.4 mm (8 mm)<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/203986/2023-09-22_0v23d88ecbk7.jpg"></figure>&nbsp;

Split Ring (2 shapes x 6 sizes)

organizers

Drathus

Remix of the Stargate Coaster by PastryThis thins out the coaster's thickness and also splits the wormhole event horizon insert into its own piece. If someone wants to model up an IRIS insert that could be a handy option to add to the list!

Stargate Coaster - Two piece with Wormhole Insert

Models/Gifts

asc_ii

This is a remix of the great design of <a href="https://www.printables.com/model/461345-bambu-poop-chute" rel="nofollow">Bambu Poop Chute</a> by <a href="https://www.printables.com/@KevinV_460266" rel="nofollow">Fantasy3DPrintsShop</a>Uses 6x3mm magnets to attach the chute to the back of the X1C, P1P or P1S case.No supports are required.I printed using these settings:<ul><li>0.4mm nozzle</li><li>2 layer wall</li><li>no support</li><li>10% infill</li><li>no brim</li><li>no supports</li><li>top surface only ironing</li><li>adaptive layer height (using the default adaptive layer bambu studio settings)</li></ul>Used 380g of filament and I was able to use ludacris mode after the base layers were printed to decrease the print time.6x3mm magnets are easily sourced from amazon, ebay or aliexpress. I used N45 grade which gives nice attachment strength.The magnets are a tight fit when pushing in. If it feels too tight, use a craft knife to gently scrape, sand or cut away the top of the hole to enlarge slightly. If you make too large - no problem just use a bit of super glue to hold the magnets in.