kingtoyo

C4talyst

说明：基于我的0.1版本重新设计的直插itx机箱&nbsp;兼容性说明支持MINI-ITX/MINI-DTX主板（17 by 17 cm or 17 by 19 cm）135mm以下CPU散热器(仅支持风冷)243mm长度显卡(4070 FOUNDER'S EDITION,4070 super FOUNDER'S EDITION)&nbsp;&nbsp;物料说明:打印材料：建议使用ABS或尼龙材料进行打印，打印时需要严格控制打印仓温度，否则可能会引起翘边导致打印失败需要准备800g 以上的ABS 耗材完成打印需要m3滚花螺母 10颗 规格（长度5mm-8mm 外径4.5mm左右）需要m3沉头螺丝 6颗 规格 （长度10mm-12mm）m3主板固定螺丝4颗（长度6mm-8mm）&nbsp;侧板可以在内侧粘一块亚克力板，230mm*240mm大小，厚度5mm（影响风冷散热器高度）&nbsp;&nbsp;！！！注意：前面板的开关位置我已预留为空白，请打印前修改此处来适配你的开关和前面板I/O！！！或者用直接使用打印预设而后添加外置开关ENG:&nbsp;Redesigned from my itx chassis ver0.1.&nbsp;Capabilities:MINI-ITX/MINI-DTX(17 by 17 cm or 17 by 19 cm)CPU COOLER UNDER 135MM HEIGHT(AIR COOLING SYSTEM ONLY)243mm LENGTH GPU (4070 FOUNDER'S EDITION,4070 super FOUNDER'S EDITION)&nbsp;BEFORE PRINGTINGMake sure you own 800g + ABS filament at leastprepare :10 knurled nuts(5-8mm with outside diameter about 4.5mm)6 countersunk screw(10-12mm)4 screw for mother board mount(6-8mm)&nbsp;ATTENTION: Please edit the Front pannel area for I left the POWER BUTTON BLANK,OR just print the preset file and then use an external power button.

ITX CHASSIS SFX PSU 243MM GPU 135MM CPU COOLER,unibody cases

nordie92

<h2>Beercycle Mk2 - Let your bike hold your beer</h2>Dont hold your drink while driving!&nbsp;&nbsp;This is the second iteration. You can find the first version <a target="_blank" href="https://makerworld.com/en/models/387872" rel="nofollow noopener">here</a>.&nbsp;In this version, the gyroscope rings do not need to be glued; they hold together solely through their shape. Additionally, the mounting ring is screwed onto the gyroscope, making it rotatable. This provides more options for attaching the beer holder.&nbsp;Bottle holder diameter: 68mmBottle holder height: 100mm&nbsp;Small German beer cans are 120mm high, making them easy to grab. And large cans, with a height of 168mm, won&#39;t roll over.&nbsp;Recommended material:- 1x Screw M5x25 (For cramp hinge) - 1x Hex socket screw M5x20 (For cramp connector)- 1x Screw M5x20 (To connect cramp and gyroscope)- 3x M5 Nut

Beercyle Mk2 - Let your bike hold your beer

自行车配件

DatumCAD

A sliding limit block that can be attached to your existing steel ruler. Incorporates an easy to use thumb cam lock with positive snap shut to ensure the ruler does not slip once held. Allows you mark-out / scribe dimensions simply & repeatably. The wide face of the block helps to keep square up against the object.&nbsp;To avoid too many variations, this listing is intended to capture the most common sizes for MEDIUM steel rulers, usually around 300mm (12") long. Most of which fall in the range of 25-27mm wide. For other ruler widths click on the below links to listings:<ul><li><a target="_blank" href="https://makerworld.com/en/models/213556#profileId-233110" rel="nofollow noopener">SMALL Steel rulers, 15-20mm wide</a> (Most 100-200mm / 4-8" Long Rulers)</li><li><a target="_blank" href="https://makerworld.com/en/models/213633#profileId-233172" rel="nofollow noopener">LARGE Steel rulers, 28-30mm wide</a> (Most 400-600mm / 16-24" Long Rulers)</li></ul>Simply measure your rulers width and thickness and pick the Print Profile with the nearest dimensions in its title.&nbsp;Tip: this is made super easy if you are measuring with digital calipers, and just round down/up any decimal places……examples below;<ul><li>if your ruler measures 25.1mm wide x 0.75mm thick, you would chose the “Rulers upto 25mm x 0.8mm” profile.</li><li>if your ruler measures 26.3mm wide x 0.95mm thick, you would chose the “Rulers upto 27mm x 1.0mm” profile.</li></ul>To assist with selection I have uploaded an Excel file in the Documentation (bill of materials section). It is titled ‘Limit Block Size Checker’ and will do all the math to let you know the best profile to chose…..or let you know if there isn't currently a suitable profile available.&nbsp;Fasteners: For these limit block sizes you will need 2x M3 fixings which act purely as strong pivot axles to the cam lever. Optimally these would be 16mm long but you could also use any M3 fixing down to as low as approx. 8mm long.&nbsp;Assembly:<ul><li>Insert the CAM lever into the Housing. Tip: Insert with the level in the closed / horizontal position as this is the angle it slides in easiest.</li><li>Insert M3 Fixings. Tip: The fixings should pass though the limit block housing holes unhindered, but then will need lightly screwing into the CAM lever handle hole which has been deliberately sized so as to require some tightening without to much force. (Remember these are just acting as pivot points, no need to tighten down hard, but equally the fixing should not want to fall back out either.)</li><li>Insert Ruler: Top Tip: The ruler is far easier to push in from the front (through the small slot in the block). This is due to the mechanics of the CAM.</li><li>Enjoy - your sliding limit block is now ready to use. Note: The first few engagements of the thumb lock may be a little hard but should ease up slightly after a few uses. If not you could try printing a smaller CAM lever from another Print profile of the same width.</li></ul>I love designing for 3D printing, please take a look at all my other models which are all free (and will always continue to be)… if you value any of the downloads enough & are able to support me, then please consider buying me a coffee to keep me going! <a target="_blank" href="https://www.buymeacoffee.com/DatumCAD" rel="nofollow noopener">www.buymeacoffee.com/DatumCAD</a><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/677805/2024-02-29_1d4977f932d5.png"></figure>&nbsp;

Limit block (Medium) Steel Rulers

实用工具

上进的up主

Use this Attack on Titan hook to imbue your belongings with the strength of giants. During printing, apply glue to the base to avoid failures due to numerous small parts. When assembling, pay attention to the sequence and orientation—attach gears first before the outer shell and base. Insert the sliding gear bars, maintaining their initial position, and then install the two small gears.用这款进击的巨人挂钩，让巨人的力量保护你的物品 打印的时候，因为有很多细小的零件，尽量在底板上涂上胶水，以免打印失败。装配的时候，注意装配顺序和方向，外壳和底板最后装配，先安装好齿轮。安装齿轮时，先将上下滑动的齿轮条装入，保持初始位置，再装配2个小齿轮。

ITX

自行车配件

实用工具

有趣