Richie

Print Design

Add a touch of perpetual beauty to any space with our eternal rose with stem. Perfect for memorable gifts, decor, or as a collectible. This rose offers a unique way to enjoy the elegance of flowers without the need for maintenance.

Rose With Stem

gifts

Brawntfxx

Here is a Chess Set for clumsy gamers.&nbsp;JUST ADDED a pocket size profile!!!! The only difference in the print is the bottom piece. The full size version has just a hole for a finger to release the board. The Pocket size version has a small lever that needs to be pushed to down position, to raise the board over the ledge so it can slide out. There are still 96 magnets holes which all fit one 2mmx4mm magnet each. I highly recommend the magnets for the small version. Its hard to play a game without them.&nbsp;I have all the pauses required and all the holes for the magnets all set in the right places. The holes are meant to each hold one 2x4mm circle magnet with a little tolerance to achieve the satisfying click of a piece being moved on the board.&nbsp;Be sure you have enough magnets. Its 64 squares, and 32 pieces. That totals 96 magnets required.&nbsp;Also be sure to have a strategy for ensuring the correct polarity of the magnets. The bottom of the pieces should attract to the top of the board. Obviously.&nbsp;Luckily the magnets attraction to the build plate is stronger that their attraction to the nozzle. So you don&#39;t have to worry about magnets coming out of there holes as the nozzle passes over.&nbsp;The Supports on the bottom container need to be removed carefully and with some patience. However you don&#39;t need the Bottom Box to have a game of chess.You also don&#39;t need to add magnets. Its just that I&#39;m clumsy.&nbsp;

Chess Set (pocket size profile)(magnetic optional)

chess

trendspoke

A small tablet holder to hook to an airplane table. Holding together by magnetsThe middle holder isn't really necessary, just made it to hold 2 devices a bit overlapping in the middle.

Airplane Device Holder

travel

Hanti_3d

Smallest possible hard-shell protective case for just the Mavic Mini by itself. Now when I go hiking with my fanny pack, I can slip this in and it can't take up any less space. Plus it looks pretty darn cool. This case truly "fits like a glove". There is virtually no movement inside when you gently shake the closed case. I designed it so that the drone rests on it's "belly" surface inside the case. There is no contact with the gimbal protector, and no weight bearing on the rotors underneath. No padding is necessary since nothing moves. To "trap" the lower props, I put the drone on the table upside-down and arrange the bottom props and then lower the case down onto the drone before picking the whole thing up and turning it back over. Then arrange the props on the top and put the lid into place. The Lid "clicks" lightly on with the protruding, tabs. In this case, "protruding" means, "take care or you'll snap them off". With any degree of care, the tabs should last and last.

DJI Mavic Mini / Mini 2 Case 

dji mini 2

jarvizar

3D miniature of Midtown Manhattan!&nbsp;Model spans from the East River to the Hudson river & 25th St. to 60th St.&nbsp;&nbsp;Check out my collection of other Large miniature cities: <a target="_blank" href="https://makerworld.com/en/u/1935755220/collections/468505" rel="nofollow noopener">https://makerworld.com/en/u/1935755220/collections/468505</a>&nbsp;New York City miniatures collection: <a target="_blank" href="https://makerworld.com/en/u/1935755220/collections/177621" rel="nofollow noopener">https://makerworld.com/en/u/1935755220/collections/177621</a>&nbsp;&nbsp;This model was designed to be printed with a 0.4mm nozzle and 0.16mm layer heights. Try using a 0.2mm nozzle (0.08mm layer heights) or scaling up for even finer detail!&nbsp;Note: If roads or other small details disappear after slicing, try lowering the extrusion/line width of external perimeters (outer walls) closer to 0.4mm OR use Arachne walls.&nbsp;<h2>Framing Details</h2>&nbsp;This model measures almost exactly 7.5x9.5in (241.32mm X 191.08mm) and should fit most 8x10 frames (assuming frame lip/overlap is around a half-inch). Feel free to change the scale/size of the model(s) to meet your needs.&nbsp;Personally I use these cheap wooden frames from Amazon: <a target="_blank" href="https://www.amazon.com/dp/B08XVP48KQ" rel="nofollow noopener">https://www.amazon.com/dp/B08XVP48KQ</a>And blue printer paper: <a target="_blank" href="https://www.amazon.com/Astrobrights-491618-Multipurpose-8-5-Inch-11-Inch/dp/B00006IDQT" rel="nofollow noopener">https://www.amazon.com/dp/B00006IDQT</a>&nbsp;I also included a large printable frame (w/ 1mm water plate) designed to fit my large miniature cities.&nbsp;Note: This is a “large” miniature and will not fit the smaller ~5x7inch printable frame included with the other miniature cities!&nbsp;A frame is not required! This model looks great by itself and can be displayed almost anywhere.&nbsp;

New York City Manhattan (Large 8x10)

Spiers

Gopro camera mount for 45mm race car roll cages, or other tubes. Held on with two cable ties. I used double sided tape to prevent the mount moving as a precaution.

45mm Roll Cage Action camera Mount (GoPro style bracket)

gopro

samfas02

I made a bobber in the shape of a scuba tank. Thanks for cheking out my model!

Scuba Tank Bobber

fishing

I loved the original art but did not want a lightbox.&nbsp;Kept just the “logo”, scaled down, and added a hole to thread a keychain.&nbsp;I removed the text because it didn&#39;t look good scaled down.&nbsp;Did you know SCUBA stands for Self Contained Underwater Breathing Apparatus?

SCUBA Diving Sports Logo Keychain

SCUBA

platini76

I am the original creator of this fun keychain. more models comes in these days if makers will download this one.a coaster, a sign, cards, lightbox, ecc ecc.. stay tuned on fuckbook!&nbsp;no screws, print in place. you can change some parts color at your desire.&nbsp;here all other &nbsp;if you like please help me funds my design and filaments for prototypes PLEASE Consider To Download this model and boost it, IT IS COSTLESS FOR YOU and SUPPORT my work.thank you&nbsp;is you want to resell in your shop contact me.&nbsp;<figure class="table" style="width: 165.81px"><table class="ck-table-resized" style="border: 1px double rgb(179, 179, 179)"><colgroup><col></colgroup><tbody><tr><td style="border: 1px solid rgb(191, 191, 191); padding: 0.4em"><figure class="image"><a href="https://buymeacoffee.com/platini76" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000455170/design/2024-05-04_5b0f81fd2a5f9.png"></a></figure></td></tr></tbody></table></figure>

Middle Finger Keychain Facebook FaceFuck

keychains

SavageLau

Hey guys, this is my table organizer design for MakerWorld Office helper contest. (3/5)&nbsp;This design have many elements. Please check detail description and print profile break down below:All design is muti-color capable, but takes really long time to print.This design have some big first layer models. Make sure you clean your build plate, and enable bed leveling before prints. Some of the boxes edges might very easy to curve up, if you fail to do so.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/454482/2024-01-17_35ec2371ea6de.png"></figure>&nbsp;<h2>Elements:</h2><h3>Tunnel:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/454482/2024-01-17_1e83b412309e9.png"></figure><h3>Block box:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/454482/2024-01-17_6d6e9fe944d04.png"></figure><h3>Question box:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/454482/2024-01-17_f36ac575df8b9.png"></figure><h3>Star and coin container:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/454482/2024-01-17_5810c509a6e7e.png"></figure><h3>Bucket:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/454482/2024-01-26_d13696b40a3b.png"></figure><h3>Holder 4 & 3 slots:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/454482/2024-01-17_6b8e4c56fd1e2.png"></figure><h3>Drawer 4 slots:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/454482/2024-01-17_b9b71497afbdd.png"></figure><h3>Drawer 3 slots:</h3><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/454482/2024-01-17_be968b6848ba9.png"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/454482/2024-01-17_54f4281440f91.png"></figure>&nbsp;<h3>Muti-color:</h3>It is very easy to paint the model. But takes way too long to print, so I did not put it on my printing profile. You can try it.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/454482/2024-01-17_ce2597d7373d2.png"></figure>&nbsp;<h2>Filaments color: </h2>@dprodriguezf was comment regarding filament colors, here is the lists:Tunnel: Bambu Lab PLA (Green)Coin/Start container: Creality Ender PLA (Skin)Questions box: Sovol PLA (blue)Bucket: R3D UV-color change PLA (Pink)Short block: wood, R3D UV-color change PLA (Purple)Longer block: Giantram PLA (Blue Marbel), Giantram PLA (Matte Terracotta)Drawer 3 slots: Creality HP Series (Matte red)Drawer 4 slots: 3DF (Coral)

Modular Mario desk organizer

desk

Willi 3D

Create your BaBo organizer! A system created to store them all!&nbsp;Description:This is the BaBo top lid module. Maximum accessibility for the tools you need most often.<figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/draft/568390/2023-09-08_b86h9lauvcyx.jpg"></figure>BaBo organizer is a stationary, very flexible system to store your tools, spare parts and even printing plates. The design is based on the iconic look of the Bambu Lab X1 printer. The entire system uses only 1 type of screw, M3x8 countersunk screws.&nbsp;&nbsp;Links:<ul><li><a target="_blank" href="https://makerworld.com/de/u/24485025/collections/12914" rel="nofollow noopener">BaBo collection</a></li><li><a target="_blank" href="https://makerworld.com/en/u/24485025/collections/666853" rel="nofollow noopener">BaBo duo collection</a></li><li><a target="_blank" href="https://makerworld.com/en/u/24485025/collections/666866" rel="nofollow noopener">BaBo inserts</a></li><li><a target="_blank" href="https://www.printables.com/@Willi/store" rel="nofollow noopener">Exclusive models, printables. (Credit card)</a></li><li><a target="_blank" href="https://than.gs/u/1578655?plans=true" rel="nofollow noopener">Exclusive models, thangs. (Paypal, Credit card)</a></li></ul>Update:(13/09/23)<ul><li>Assembly optimizations</li></ul>(31/10/23)<ul><li>print profile optimizations (side panels are printed upside down to get a better top surface)</li></ul>(15/01/24)<ul><li>lid reinforcement</li></ul>(18/01/24)<ul><li>tighter fit of the lid</li><li>rounded corners to avoid warping on the edges</li></ul>&nbsp;Printing:Layer height: 0.2Supports: YesBrim: NoMaterial: allRemove the purgeline afte the start of the lid part print and do not use filament calibration!&nbsp;Assembly:Follow the instructions in the picture.<ul><li>printed parts</li><li>14 x M3x8 countersunk screws.</li></ul>If you like this model, please throw me a like. Designing the models is time, filament and coffee consuming. <a target="_blank" href="https://www.paypal.com/donate/?hosted_button_id=WGL5LXN5EHEXN" rel="nofollow noopener">If you want to support my work buy me a coffee (PayPal).</a> Thanks!

[BaBo] top lid module

babo

organization 

mario

fantasticmrdavid

A Retro Desktop PC style case based on an old 286 PC I grew up with. Designed to fit a Raspberry Pi with a 3.5 inch HDMI MPI3508 LCD display. This version is V2 featuring the following improvements over the <a target="_blank" href="https://www.printables.com/model/654635-retro-desktop-pc-raspberry-pi-case" rel="nofollow noopener">original</a>:<ul><li>Boot SD card reader placed in the 5.25 floppy drive that connects to the Pi&#39;s Micro SD card reader.</li><li>Fan mounts in the desktop base for 2x 25mm fans.</li><li>Improved front panel design enabling easier multicolour printing. The panel can also now be removed without needing to disassemble the rest of the desktop allowing for easier access to the Pi.</li><li>Display brace allows for easier alignment of the 3.5&#34; display inside the monitor shell when closing up.</li><li>Rear I/O USB port so that the power cable can connect like a real PC instead of directly to the Pi.</li></ul>&nbsp;In addition to the print you&#39;ll need:<ul><li>Raspberry Pi (I used a 4B but you should print the desktop base to match your Pi)</li><li>3.5 inch HDMI MPI3508 LCD display (such as <a target="_blank" href="https://www.aliexpress.com/item/1005004358609772.html?spm=a2g0o.order_list.order_list_main.11.66c81802hHpPTF" rel="nofollow noopener">this one</a>)</li><li>Micro SD to SD Card flexible extension cable (<a target="_blank" href="https://www.amazon.com.au/gp/product/B00S6AMWK2/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&amp;psc=1" rel="nofollow noopener">this one</a>). The reader drive part has been specifically designed to fit the one in the link as others I tried were too big on the micro-SD side to fit the desktop base. The correct orientation for the SD reader is for the SD card to be inserted with label facing up.</li><li>HDMI flat flexible cable (such as <a target="_blank" href="https://www.aliexpress.com/item/1005005512402056.html" rel="nofollow noopener">this one</a>). I used D2 + A2 + 15cm cable from the link.</li><li>1x 0.1m USB-C extension cable (such as <a target="_blank" href="https://www.aliexpress.us/item/1005006318686761.html" rel="nofollow noopener">this one</a>) to allow the Pi to be powered from the rear I/O panel.</li><li>1x M1.5x8 dowel pin (such as <a target="_blank" href="https://www.aliexpress.com/item/4000473863693.html" rel="nofollow noopener">this one</a>) for the SD card drive latch.</li><li>40 pin GPIO extension cable (such as <a target="_blank" href="https://www.aliexpress.com/item/32391134102.html" rel="nofollow noopener">this one</a>). When assembling, try to keep as much of the extra slack in the monitor as possible to leave room in the desktop for the other cables.</li><li>1x M2.5x8 screw for securing the USB-C port brace to the desktop base.</li><li>4x M2.5x5 screws for securing the Pi to the desktop base.</li><li>4x M2.5x5 screws for securing the desktop case to monitor base.</li><li>1x M2.5x5 screw for securing the SD drive brace to the front panel back.</li><li>2x M2.5x8 screws for securing the desktop case to desktop base.</li><li>2x M2.5x8 screws for securing the display brace to the monitor front.</li><li>4x M2.5x8 screws for the monitor.</li></ul>Optional:<ul><li>Pi speaker expansion board (such as <a target="_blank" href="https://www.aliexpress.com/item/1005005237254806.html" rel="nofollow noopener">this one</a>).</li><li>Dual 25mm fans connected to LCD display 5v pins (such as <a target="_blank" href="https://www.aliexpress.com/item/1005004604550471.html" rel="nofollow noopener">this one</a>). I also needed a <a target="_blank" href="https://www.aliexpress.com/item/1005005702193703.html" rel="nofollow noopener">JST 2-pin extension cable</a>.</li><li>8x M2.5x10 screws for securing the fans to the desktop base.</li></ul>All parts except the following should be printed with supports:<ul><li>monitor connector</li><li>front panel face</li><li>front panel back</li><li>drive latch</li><li>display brace</li><li>USB-C port brace</li></ul>I used eSun Bone White PLA but my options for a close matching beige were limited where I am. I used a Molotow Liquid Chrome marker to paint the front panel key lock. I used a label maker to print my front panel sticker. Credit to <a target="_blank" href="https://www.printables.com/@Rooper_881255" rel="nofollow noopener">@Rooper</a> for the rear monitor sticker.&nbsp;OS Configuration notes:I followed <a target="_blank" href="https://www.hypn.za.net/blog/2020/05/03/booting-a-raspberry-pi-to-dosbox/" rel="nofollow noopener">this guide by @Hypnza</a> to get the Pi to boot into DOSbox with retro splash screen. I&#39;m running DOSbox under Debian Bullseye (As of writing I couldn&#39;t get the custom splash screen to work under Bookworm). After installing the <a target="_blank" href="https://github.com/goodtft/LCD-show" rel="nofollow noopener">LCD-show display drivers</a> I used the following values in my /boot/config to get the output to fit the monitor and rotate to the correct orientation:overscan_left=20 overscan_right=55framebuffer_width=640 framebuffer_height=480Add to the [all] section:dtoverlay=tft35a:rotate=270 display_rotate=2 Add the following if using the above linked audio module: dtoverlay=audremap,pins_18_19&nbsp;CHANGE LOGApril 12 2024<ul><li>Uploaded correct front plate stl.</li></ul>

Retro Desktop PC Raspberry Pi case

Source robotics

FOR THE MOST UP-TO-DATE ASSEMBLY MANUAL AND STL FILES GO TO GITHUB: Github: <a target="_blank" href="https://github.com/PCrnjak/PAROL6-Desktop-robot-arm" rel="nofollow noopener">https://github.com/PCrnjak/PAROL6-Desktop-robot-arm</a>PAROL6 is 6 axes desktop robotic arm. It is a robotic arm whose design approach is driven by real needs from a robotic education standpoint, small automation, and scaling from RnD to production. It is the culmination of devolvement and feedback of 2 previous robotic arms I made, both being very successful open-source projects. PAROL6 uses precision planetary gearboxes and belts with careful placement for optimal weight distribution. The design is modular and allows easy addition of closed-loop drivers. From the software side, it uses the custom protocol to allow for industry standard 60-100 Hz loop times. Modern GUI is inspired by industrial and cobot interfaces where all standard ways of control are implemented (resolved rate, cartesian level control, joint level control, motor jog...) It includes a simulator to test your programs without needing a physical robot. PAROL6 is feature-rich with an Isolated I/O, CAN bus, and compliant gripper...All information on how to build and how to use PAROL6 is on GitHub: <a target="_blank" href="https://github.com/PCrnjak/PAROL6-Desktop-robot-arm" rel="nofollow noopener">https://github.com/PCrnjak/PAROL6-Desktop-robot-arm</a>Join discord: <a target="_blank" href="https://discord.gg/prjUvjmGpZ" rel="nofollow noopener">https://discord.gg/prjUvjmGpZ</a> Join forum: <a target="_blank" href="https://discourse.source-robotics.com/" rel="nofollow noopener">https://discourse.source-robotics.com</a>Follow the project on YouTube: <a target="_blank" href="https://www.youtube.com/@source-robotics" rel="nofollow noopener">https://www.youtube.com/@source-robotics</a>Follow the project on Instagram: https://www.instagram.com/source_robotics/If you are interested in buying a kit or assembled robot send us an email on: Info@source-robotics.com

PAROL6 3D printed desktop robotic arm

projects 

nnamrakk

Saw many different light switch plates that were building brick like (unnamed brand) out there. However, I seemed to always have issues with printing and certain blocks (not to be named) would not stick, you couldn&#39;t get it on or off properly. I did mine in PLA, but you can do PETG for a little more durability with lasting. Been using them over a year, but the kids don&#39;t take Lbricks on and off constantly, so far so good on durability.&nbsp;Added the double decorative switch plate for those that need it.&nbsp;.16 layer heightironing on - I use 15% at 30mmSupports - I used Default Snug supports.&nbsp;UPDATE: 5/29/24 - Added the Triple and Jumbo plates that were requested. Please test them out and let me know if there is an issue with them I can adjust. I don&#39;t have any Triple switches in my house so measurements were best I could do off a standard plate.

Brick Building Block - Light Switch Plates

house

Jelarsen.D15

Rear bowtie logo replacement for Chevy Volt (made logo to replace the stolen logo from my car)Logo as seen in photo is 7 inches wide.

Chevy Bow Tie Logo - Replacement for rear badge on Chevy Volt

chevy logo

josh.davis

2x2x6 (standard height) Gridfinity bin for holding Bambu P1S spare parts. Not stackable and overall height when full is approximately 66mm tall which should fit most workbench drawers.Spots for:<ul><li>2 wipers</li><li>3 filament cutting blades</li><li>6 slots for grease</li><li>2 nozzles</li><li>1 heater nozzle bracket</li><li>1 bin for loose screws and other parts. Also fits the cardstock sleeves the scraper blades fit into fairly snugly.</li></ul>

Gridfinity P1S Spare Parts Bin

3d printer

adw.dsgn

My cup holder adapter is designed to fit Stanley&#39;s, Yeti&#39;s, Hydrofask&#39;s and other comically large water bottles in your puny cup holders. There are various base sizes from 85mm to 65mm in diameter to fit inside various cup holders. The TPU restraining tabs are optional but are required for any bottle too small to fit the 100mm inner diameter of the adapter. I recommend you add a dab of super glue to hold them in place. If none of the available sizes fit your particular cup holder, post the diameter and depth of your vehicles cupholder and I will try to upload a variation that fits. If your vehicle gets too hot, consider printing it in more temperature resistant material like PETG

Car Cup Holder Adapter with flexible TPU tabs

8020 / vanlife

wesyarber

My printer is stored in a closet with a lot of unused clothes rack space, so this is a perfect solution for me. This is not a remix but is inspired by <a target="_blank" href="https://www.printables.com/@Jackson" rel="nofollow noopener">Jackson</a>'s <a target="_blank" href="https://www.printables.com/model/165877-closet-rod-filament-hanger-3in" rel="nofollow noopener">original design</a>. I redesigned these to be much lighter / use less filament and to accommodate slightly wider cardboard spools with plastic rings around them for the AMS. This was not designed to feed filament to the printer straight from the hanger but just for storage. It is possible that it would do fine to feed filament directly from this, but I do question how well it would hold up if the filament got tangled and the extruder pulled with a lot of force on the spool. For generic PLA, it cost about $1 USD and takes an hour to print a pair of these. You can fit 3 pairs of them on the X1's build plate at a time if you rotate them cleverly. See the included print profile. Please let me know if you print this for yourself and find it useful!

Filament Storage Hanger

filament racks

Morrow

Made this for someone who was cosplaying Dave Strider at a convention. Simple design that utilizes the multicolour function of the printers.

Dave Strider Record keychain

toys

Adam L

Whether you are a DIY enthusiast or a professional, you know how important it is to drill holes that are square to the surface. But sometimes, it can be tricky to achieve that, especially on round or curved surfaces. That’s why you need a DrillSquare.This model is a simple but effective drill guide that has a V-shaped groove that fits on flat and curved surfaces. You just need to hold it flat to the desired surface and insert your bit into the matching hole. Then, you can drill with confidence, knowing that your hole will be square to the surface. Best printed in PETG or low friction filament like nylon, to ensure durability and smoothness. PLA might have problems with drill bit friction. I recommend using this to start drilling a square hole, removing the guide after getting a good bit into the material, and then finishing the drilling job after you've got enough of a hole started to ensure you're drilling square.DrillSquare is a must-have tool for any drilling project. Try it today and see the difference! It is provided as 3MF, and also a Fusion360 file if you wish to customize the hole sizes/choices.<h4>Printing Notes</h4><ul><li>Should print fine at 0.2 layer height. Print the “V” side up to prevent any part warping, and a brim is also recommended in case of issues. While you could print “V-side down”, this is not recommended, as it can lead to warping. </li><li>Use 4 walls, or more. You want the holes to be strong and the structure to be rigid.</li><li>The holes have a built-in tolerance of 0.2 mm around the diameter, as plastic tends to shrink. My testing shows this works well for PETG. <ul><li>If you want to tweak this, either scale the model slightly (easy way), or change the offset in the fusion model here:</li><li><img src="https://media.printables.com/media/prints/650026/rich_content/ce690a57-9714-456e-bac2-f6ab6f1fe084/image.png#%7B%22uuid%22%3A%2243146e8e-d72c-435a-adc4-531a7772959d%22%2C%22w%22%3A662%2C%22h%22%3A488%7D"></li></ul></li><li>PETG or higher temperature resistant filaments recommended, although PLA should also work as long as you don't expose it to a warm drill bit. Low friction like nylon is also desirable.</li></ul>&nbsp;&nbsp;

Customizable DrillSquare:   Master the Art of Drilling Square Holes!  (Imperial and Metric)

tools

MizarIT

Reupload of my previous model with photo of the 3d printed part&nbsp;Replacement pods for aerogarden&nbsp;Printed in pla 0.2 or 0.3 is perfect&nbsp;Step avaible for edit the hole size

Aerogarden replace pod - Step avaible - REUPLOAD

plants

vanis

Compatible bottles:Hydrapak, Katadyn Befree or ordinary PET bottle