RCR970

bcarlson320

Skull makeup brush holder I made for my girlfreind.

Makeup Brush Skull Holder

Lindsay's collection

xchgre

Image of the Moon, the Earth's only natural satellite. It is a rocky, cratered object, which is tidally locked to the Earth at this time, so one face is visible from Earth. The far side of the Moon is visible only to cameras and humans aboard spacecraft that have orbited it. Author/Origin/License: Dr. Carol Christian, HST Outreach Project Scientist and 3D Astronomy@STScI Team Lead, Public Domain

Moon - Ultra high detailed

moon

Docean

Humanoid knife holder 2mm Hole width and 3mm Hole width&nbsp;&nbsp;

Humanoid knife holder 

kitchen stuff

mcmaven

I designed this for a friend who has his P1S on a shallow bench against a wall. He has 4 inch duct work, but only 2.5 inches between his printer and the wall. This vent maximizes air flow and provides a 4 inch exhaust, while only being 53 mm (2.1 inch) deep. It is also designed to provide to not interfere with 1-way or 4-way AMS hubs. The exhaust vent has a 4 inch OD and a 3.75 inch ID, and is 1.625 deep.  It can be attached several ways:- Ten 10x3 mm round magnets. Best if all oriented the same way.- Double sided sticky tape.- Two #6x1/2 inch sheet metal screws. My P1S had some unused screw holes in the back panel.&nbsp;I put some 1/8 inch foam tape around the inlet to prevent leaks, and used sheet metal screws to secure it. An exhaust hose that is not strain relieved can put a lot of torque on the exhaust vent. Magnets may slip, and double sided sticky tape may slip over time. I recommend using screws if you have the holes in the back of your printer.&nbsp;I did not test this on an X1C, but I believe they have the same physical case as a P1S.

Low Profile Exhaust Vent

printer stuff

BODY3D

If you like my work, support me by leaving a like !Get access to really cool models every months on my PatreonAnd don't Forget to Follow me !<a target="_blank" href="https://www.patreon.com/BODY3D" rel="nofollow noopener"><img src="https://dreamityourselfmusician.com/wp-content/uploads/2020/10/patreon-france.jpg" alt="BODY3D"></a><a target="_blank" href="https://www.tiktok.com/@body_3d" rel="nofollow noopener"><img src="https://encrypted-tbn0.gstatic.com/images?q=tbn:ANd9GcSrfIHeAYT6KeLQTVHxvXORYsILY6oVXlNVmg&usqp=CAU" alt="BODY3D"></a> <a target="_blank" href="https://cults3d.com/en/users/BODY3D/3d-models" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/user/3079230113/draft/2023-08-21_6b0967a6c4cbc.png"></a> <a target="_blank" href="https://beacons.ai/body3d" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/user/3079230113/draft/2023-08-21_63b5664660755.png"></a>

Articulated Onix

pokemon

Calzune

CatLove Silhouette Wall Art

Wall art - CatLove

cats

Riffcat

This Headset Hanger fits desks from a height of 5mm to 40mm. Use the Long screw for desks thinner than 18mm.I printed it with a 0.4mm nozzle and a layer height of 0.2mm with PLA on My Ender 3 which worked well for me. Also, I wouldn't use supports as they may mess up the threads and the threads print well without them. I would recommend printing this with more infill than standard prints for rigidity. Some people may need to do some trimming or sanding to fit the thread into the hanger as it is a tight fit but it is designed like that so it is secure. The maximum headset width is 4cm which is enough to fit most headsets like my SteelSeries Artis 1. Also, I would print the threads without supports as they are hard to remove and it prints just fine without them. I have also shared this design on Printables.com for convenience <a target="_blank" href="https://www.printables.com/model/361953-headset-hanger-v1" rel="nofollow noopener">https://www.printables.com/model/361953-headset-hanger-v1</a>. By the way if you can see any issues with this design or anything that can be improved then please tell me your ideas in the comments section as I read all of the comments on my designs. Thank You.UPDATE (V1.5) I have kept the thread the same so that if you were struggling with the screw before, you can keep the thread and print a new screw. I have adjusted the tolerance on the screw and have moved it by 0.1mm which will make a huge difference while still keeping snug. I have shown some images of the changes I made to the screw which may be helpful to some people. I have also added the CAD fusion files to this design with both new screws so people can make remakes of this design. Thank you for the support and feedback.

Lindsay's collection

moon

kitchen stuff

printer stuff

pokemon

cats

production