Misakov

Carry the Knuckle Spike Self Defense with you at all times. Can be attached to a belt.Press firmly until you hear a click as the pins snap into place. Use an 1x M5 (30mm) screw and nut to attach to the belt.&nbsp;The case is suitable for this model:<a target="_blank" href="https://www.printables.com/cs/model/820987-self-defense-knuckle-spike/files" rel="nofollow noopener">https://www.printables.com/cs/model/820987-self-defense-knuckle-spike/files</a>

Case for Knuckle Spike 

Hunting/Fishing

Mats3DPrints

Mathematics board for youngsters or anyone who has difficuilty with numbers, help with school and make learning fun with this easy support free print.&nbsp;

Mathematics Board game

Learning

Allpa_112

I loved a similar wooden construction toy when I was a child. However, as more and more components break and my children show a lot of interest in building and constructing, I have started my own printable system.The files in this set form the basis for BUILDfinity and already allow an unlimited number of possibilities to give free rein to your creativity. Nevertheless, I will continue to create more parts in the future to enable special sets and building projects. It will be interesting to see what else my children need ;)I have also added building instructions for three different models. So you can start by assembling a car, an airplane and a helicopter. I'm really looking forward to seeing your creations!To make the instructions easier to follow, I recommend printing the different screw lengths in the same colors as I did:10 mm = blue 15 mm = orange 20 mm = green 30 mm = red 40 mm = yellow 50 mm = grayOtherwise, there are no limits to the colors. To start with, however, at least 12 screws per length (6x round with slot and 6x hex), 6 rods per length, 2 plates per size and 10 washers, nuts and connectors each should be printed.Print settings: - min. 5 bottom and top layers - 2-3 outlines - 10% - 15% infill - 0.2 mm layer height (0.1 mm for all parts with threads) Extension-Kits available to expand possibilitys: I've a lot of extension kits for this BUILDfinity Basic-Set. They can be found on my Printables Club or on Cults3D. Just search for BUILDfinity! -----------------------&nbsp;Ich habe ein ähnliches Konstruktions-Spielzeug aus Holz in meiner Kindheit geliebt. Da hier aber immer mehr Bauteile kaputt gehen und meine Kinder auch sehr viel Interesse am Bauen und Konstruieren zeigen, habe ich ein eigenes, druckbares System angefangen. Die Dateien in diesem Set bilden die Basis für BUILDfinity und ermöglichen bereits eine unbegrenzte Anzahl von Möglichkeiten seiner Kreativität freien Lauf zu lassen. Nicht desto trotz werde ich in Zukunft laufen weitere Teile erstellen um spezielle Sets und Bauprojekte zu ermöglichen. Sind wir mal gespannt was meine Kinder noch alles brauchen ;)Für drei verschiedene Modelle habe ich gleich noch eine Bauanleitung hinzugefügt. So könnt ihr für den Start direkt einmal ein Auto, ein Flugzeug und einen Hubschrauber zusammen schrauben. Ich bin schon sehr gespannt auf eure Werke! Damit die Anleitungen einfacher umgesetzt werden können empfehle ich die verschiedenen Schrauben-Längen in den gleichen Farben zu drucken wie ich: 10 mm = Blau 15 mm = Orange 20 mm = Grün 30 mm = Rot 40 mm = Gelb 50 mm = GrauAnsonsten sind den Farben keine Grenzen gesetzt. Für den Anfang sollten aber mindestens 12 Schrauben pro Länge (6x Rund mit Schlitz und 6x Hex), 6 Stangen pro Länge, 2 Platten pro Größe und je 10 Unterlagscheiben, Muttern und Verbinder gedruckt werden. Druckeinstellungen: - min. 5 Boden- und Deckschichten - 2-3 Konturlinien - 10% - 15% Infill - 0,2 mm Schichthöhe (0,1 mm bei allen Teilen mit Gewinde) Verfügbare Erweiterungs-Sets für mehr Möglichkeiten: Es gibt viele Erweiterungen für dieses BUILDfinity Basis-Set. Diese sind in meinem Printables Club oder auf Cults3D zu finden. Einfach nach BUILDfinity suchen! -------------------&nbsp;PLANE / FLUGZEUG<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/362538/2024-01-06_37fl15gkaosy.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/362538/2024-01-06_4bjdmghzegxz.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/362538/2024-01-06_z9xuah479epg.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/362538/2024-01-06_osmqoohyj7pd.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/362538/2024-01-06_szms8b8sza65.jpg"></figure>&nbsp;&nbsp;HELICOPTER / HUBSCHRAUBER<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/362538/2024-01-06_pwpimbm7jbi0.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/362538/2024-01-06_tvi1k2wbpv73.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/362538/2024-01-06_u34j9sa0pkcf.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/362538/2024-01-06_r3d08g75lj5b.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/362538/2024-01-06_oylyykjz2dse.jpg"></figure>&nbsp;&nbsp;CAR / FAHRZEUG<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/362538/2024-01-06_c10lsgqh947x.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/362538/2024-01-06_urebk4tecjbm.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/362538/2024-01-06_szb4cl81zn1a.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/362538/2024-01-06_x6vk581p67p3.jpg"></figure>

BUILDfinity construction play for kids // Konstruktions-Spiel für Kinder [BASIC-SET]

Print Next

Mdesign

<ul><li>Please download “Raw Model Files” where you can find temp coded 3MF file.</li><li>Upload this file as project into Bambulab Studio.</li><li>You can verify temp change after slice the model and switch “Colour scheme” to “Temperature”.<ul><li>You should see second image that I uploaded with model.</li></ul></li></ul>Enjoy ! ☺️🤌

ASA temp tower 25 min, 235 - 260°C

Temp Tests

JamesThePrinter

Why hide your remotes? Keep them within reach in a beautiful holder stylized with the appearance of rope! 3 models to choose from!<ul><li>Dual - Holds remotes of all sizes with two compartments</li><li>Short - Designed for smaller remotes (Firestick, Chromecast, etc.)</li><li>Tall - For full size remotes</li></ul>This is part of my Rope Series. You can view all of my Rope Series models in <a target="_blank" href="https://makerworld.com/en/u/1360890085/collections/12784" rel="nofollow noopener">this collection</a>.&nbsp;&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;The following filament was used in the pictures above:<ul><li>Prusament Azure Blue PLA</li></ul>&nbsp;

Rope Remote Holder

Dish/Bowl

Ariox3D

<h4>Three Spinning Tops Orbital</h4>I added 2 3mf files, one for pla and the other for petg and in both there are the three models, select the one you like the most or print them all 😁<h4>After printing according to your tolerance, if the pin does not fit well, sand it or glue it and orbit</h4><h4>Author: <a target="_blank" href="https://pinshape.com/items/28404-3d-printed-spinning-tops-orbital-series" rel="nofollow noopener">https://pinshape.com/items/28404-3d-printed-spinning-tops-orbital-series</a></h4><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/233940/2023-12-04_7044ae82f057c.gif"></figure> -Ariox3D-<h2> </h2>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;

Spinning Tops Orbital

Lulimu

All uppercase letters in the “Super Ocean Font”. Use for sings, hang them on walls, for presents, etc...

Super Ocean Font

Beach 

jajaum3d

🌟 Support My Work & Unlock Exclusive Benefits!🌟 Become a patron on <a target="_blank" href="https://www.printables.com/@jajaum3d#join:64" rel="nofollow noopener">Printables.com</a> and gain access to early releases, commercial licenses, and more. Kenji is your new desk companion. More than a cute robot and keychain it is an useful test print to check dimensions, overhangs and even a tiny bridge. Use the tolerances (0.25 on foot and 0.4 on legs) to adjust the extrusion multiplier of each of your filaments.I myself was very impressed of how different each filament can be, got numbers from 105% to 92% See all my designs on cults: <a target="_blank" href="https://cults3d.com/en/users/jajaum3d/creations" rel="nofollow noopener">https://cults3d.com/en/users/jajaum3d/creations</a> All my designs are protected by Copyright Law. Purchasing does not grant the right to sell any digital file or printed model of my designs without explicit consent. Please respect the hard work of 3D artists by never sharing or selling digital files.<h3> Printing</h3>No Supports, no brim.Rear seam lineOn the photos I used the default 0.2mm on PrusaSlicer:0.2 layer height15% InfillTested on PLA and PETG

Kenji  the print-in-place benchy robot

Paitons Robot

Asphalt3D

The Credit Card Cutlery Kit is a compact culinary companion crafted for convenience and cleverly concealed within a credit card frame.The size of a credit card, the kit fits in your wallet and can be used in an emergency when you forget to bring utensils. AssemblyThe fork and spoon fold like origami to create an ergonomic head angle and improved scooping volume. The three dots latch the fold to add structural strength and rigidity.You do not need to crease the fold along the entire length of the handle. Creasing along the latch area is sufficient.Creasing closer to the head will increase the head angle and spoon volume, but too much creasing may cause the thin folding layer to split.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/156756/2023-11-09_cjjrqzz5dxlr.gif"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/156756/2023-11-09_bpxswfo3atnz.gif"></figure>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/156756/2023-11-09_3gvezqkaat1b.gif"></figure>PrototypesOver 60 prototypes were printed in the process of finding a balance between strength, ergonomics, reliability and print speed.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/156756/2023-11-09_9ff0mhgpd1z0.png"></figure>Food SafetyWhile PLA is considered food safe, it is not recommended to reuse this cutlery - it is intended for one-time emergency use.We also don't know how clean your wallet is, so it's your call whether using currency-crusted cutlery is cleaner than using your hands.PrintingPrint-in-place, no supports.Designed for 0.15mm layer height with a base layer of 0.20mm.Test-printed on the Prusa Mini with PLA, completed in 35 minutes.

Credit Card Cutlery Kit

Survival 

Mushroom in two sections that screw together. The cap requires an AMS/MMU or hand painting for the spots. Because the cap is hollow, this could also be used for storage/stashing.&nbsp;Print SettingsThe mushroom cap requires a multicolor-capable printer.&nbsp;AssemblyThread together the 2 sections as shown below:<figure class="image image_resized" style="width:535.5px;"><img src="https://media.printables.com/media/prints/554734/rich_content/d588076c-c428-49e5-88ae-2bd98038cf74/thumbs/cover/800x600/png/mushroom31-2a.webp"></figure> <a target="_blank" href="https://www.buymeacoffee.com/JamesThePrinter" rel="nofollow noopener">Buy Me A Coffee</a>&nbsp;The filaments used in the pictures above: <ul><li>Polymaker PolyTerra Army Beige PLA</li><li>Bambu Lab Jade White PLA</li><li>Prusament Lipstick Red PLA</li><li>Bambu Lab Mandarin Orange Matte PLA</li></ul>

Mushroom

Fake Book/Secret Box

Garden

3D design shop

my flexible skeleton Lizard.&nbsp;It's a fun piece of toy that's incredibly flexible, with virtually all joints capable of movement. It has become a huge hit with the kids at home!&nbsp;If adhesion problems persist, I recommend adding a brim.

Articulated Skeleton Lizard

Toys

Dinozzo28

alphabet name for door etc&nbsp;70mm high&nbsp;´´´added W

alphabet name for door etc

Bathroom

PriscoRulez

Introducing the Trolex, a 3D printed working watch powered by a Miyota 2035 Quartz movement. Shock your watch-collector friends with a custom piece that will certainly attract their interest!With its 41.3mm size, this timepiece can adapt to most wrists and for all the occasions provided you use filaments that suit your taste. It is fully working and relatively easy to put together.Create your own personal wristwatch and show the world your style! Now, I also added a custom text version of the dial for your special messages.&nbsp;&nbsp;Important notes: Dial, hands and back case require a 0.2mm nozzle. The other pieces can also be done with 0.4mm nozzle, to allow more filament options (e.g. marble, sparkle, etc.) but would benefit from a 0.2 nozzle for higher quality.&nbsp;To work the watch requires a Miyota 2035 quartz movement, which is easy to find online and fairly cheap, but could be adapted to other movements by creating a custom inner movement holder. I got 5 for 9£ from Aliexpress here: <a target="_blank" href="https://www.aliexpress.com/item/1005006170752556.html" rel="nofollow noopener">https://www.aliexpress.com/item/1005006170752556.html</a>&nbsp;I do not own an AMS, so the watch is designed to be printed without one, for multi-color dial there is a pause set at the start of the 14th layer and change filament. If you do not want to change filament you will have to resume print to finish it, or remove the pause before slicing the plate. &nbsp;There are now two options for the wristband: flexible to be made with TPU (as in the cover picture) and rigid for any other filament.The rigid version is made up of pieces that need spare filament wire to be held together. This allows to adjust size by removing or adding more pieces.&nbsp;Needless to say the hands are the hardest part to get right and might require a few print (I am still working on a more reliable version of these). For reliability I would recommend buying the hands if you actually plan to use this watch as I do not know how long the 3d printed hands will last or keep the time. The second hands was too small even for the 0.2 mm nozzle.&nbsp;I printed it using a smooth PEI plate, I have not tested it yet on other plates, particularly for hands and back cover which have designs on the bottom surface.&nbsp;Building instructions:I am planning to produce a dedicated video on how to build it, in the meantime the Fusion360 scheme shows more or less where each piece should go.<ol><li>Place the movement in the holder, snap the dial in place over it and insert it into the main case;</li><li>Push in place the back case and force the spacer ring over the dial to secure the movement in place, then add the top ring;</li><li>Attach the wristband pieces using spare filament, the holes have a tight fit so it is best to use some pliers to help pushing the filament through;</li><li>Insert the stem on the movement, pull it into time-set position then screw the crown in from outside the case. (Leave enough play to allow the stem to be pushed in into normal position). Use some super glue here to fix the crown on the stem.</li><li>Set the watch into the time-set position;</li><li>Finally use some precision tweezers to push the hands in place carefully. It is not easy and might require some attempts and patience;</li><li>Turn the crown to check the hands are moving correcly and freely;</li><li>Wear it proudly!</li></ol>

Trolex - the 3D printed working wrist watch

Hygene

Pork3D

Embrace timeless elegance with the Eliezer Ring! This ring features a beautiful circular pattern, perfect for those who appreciate classic and sophisticated design. Features:Round shape with a circular patternIntricate details and smooth curves&nbsp;Printing No supports needed0.2mm NozzleDual Colour (Optional)

Eliezer Ring by Pork3D.com

Rings/Jewelry

Borgecmedia

Version 3 of my bottle cordage maker. I made a version 2 then realised that both versions 1 and 2 sucked so made a version 3. More info in video: <a href="https://youtu.be/ZrLhaQKYRrs" rel="nofollow">https://youtu.be/ZrLhaQKYRrs</a>&nbsp;The purpose of the tool is to shred plastic bottles into cordage. this cordage has many uses, such as string, as a binding material (kinda like zip ties but stronger), and to make custom cable wraps. Its also popular with bushcraft hobbyists since sadly, plastic bottles are commonplace nowadays. In a bushcraft sense it is fantastic for lashings. I demonstrate all of these uses in the video. <figure class="image"><img src="https://media.prusaprinters.org/media/prints/118602/rich_content/e367f03b-ecad-4305-9865-26854ea22be0/3.png#%7B%22uuid%22%3A%228e0d419b-0d3c-4cdd-ad92-07845c5b07f2%22%2C%22w%22%3A1000%2C%22h%22%3A1000%7D"></figure>&nbsp;Overall version 3 is much easier in every aspect. It doesn't need to be assembled, its easier to print and its easier to hold and use. Left is for left handed people and the other file is for right handed people. video includes info on how to print, use and assemble. Its a single piece print, would recommend 100% infill even if it works fine with 25.&nbsp;Apart from the printed part you need a pencil sharpener blade, a m2*16mm bolt (but bigger works fine), and optionally but highly recommended is a 15mm length of sheet metal 6.5mm wide. I used brass but whatever works. Another pencil sharpener blade works as well. The video contains build instructions but it really is very simple.

Plastic Bottle Cordage Maker (v3)

Prepping/TIOTWAWKI

EngGraph

&nbsp;&nbsp;Elegant Wine Bottle Holder for Your Kitchen Counter&nbsp;This wine bottle holder is the perfect addition to your kitchen, providing a stylish way to keep your wine bottles easily accessible and organized on the table.&nbsp;Space-Saving: The compact wine bottle holder takes up minimal space on your kitchen counter while offering a tidy storage solution for your wine bottles.&nbsp;Aesthetic Design: With its timeless and elegant design, the wine bottle holder seamlessly fits into any kitchen decor, adding a touch of sophistication to your space.&nbsp;Secure Storage: The horizontal supports ensure that your wine bottles stand securely and stably, without wobbling or tipping over.&nbsp;This wine bottle holder is not only functional but also an attractive centerpiece. It offers a stylish way to have your favorite wines within reach when you&#39;re ready to enjoy them.&nbsp;Print your wine bottle holder today and add an elegant touch of organization to your kitchen counter!&nbsp;<h2>Thank you, friends! It&#39;s impressive to observe your creativity and see how you apply your design and talent. For those who still want to print the model, I&#39;ve summarized the great results you&#39;ve shared in the comments here. I hope that others will be inspired by your designs, color choices, and material selection.</h2>&nbsp;<figure class="table"><table><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/812382/2024-01-07_711ef05a57cf1.jpg"><figcaption>Print and Design by <a target="_blank" href="https://makerworld.com/de/u/1886292574" rel="nofollow noopener">@katharina.struc</a></figcaption></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/812382/2024-01-07_fabc11917d346.jpg"><figcaption>Print and Design by <a target="_blank" href="https://makerworld.com/de/u/3128602605" rel="nofollow noopener">@cbougerie</a></figcaption></figure></td><td><figure class="image image_resized" style="width:100%;"><img src="https://makerworld.bblmw.com/makerworld/draft/812382/2023-12-19_f0b7a909f08b3.jpg"><figcaption>Print and Design by <a target="_blank" href="https://makerworld.com/de/u/1723791022" rel="nofollow noopener">@Ccb045</a></figcaption></figure></td></tr><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/812382/a4b6eb00-9c72-11ee-ae21-a32aac2dff22.jpg"><figcaption>Print and Design by <a target="_blank" href="https://makerworld.com/de/u/3007439339" rel="nofollow noopener">@GHOSTELEVEN</a></figcaption></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/812382/aac9d440-ad65-11ee-a91c-897eff7dbe9d.jpg"><figcaption>Print and Design by <a target="_blank" href="https://makerworld.com/de/u/1143904387" rel="nofollow noopener">@Ratler</a></figcaption></figure></td><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/812382/0840f770-a5f5-11ee-9f6e-970eec074b76.jpg"><figcaption>Print and Design by <a target="_blank" href="https://makerworld.com/de/u/1811672732" rel="nofollow noopener">@tturns27</a></figcaption></figure></td></tr><tr><td colspan="3"><figure class="image image_resized" style="width:96.37%;"><img src="https://makerworld.bblmw.com/makerworld/draft/812382/95696cb0-a44f-11ee-b86e-cfdb05226b64.jpg"><figcaption>Print and Design by <a target="_blank" href="https://makerworld.com/de/u/4173901069" rel="nofollow noopener">@engintakmork</a></figcaption></figure></td></tr></tbody></table></figure><figure class="table" style="width:91.83%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/812382/2024-01-09_82ca684fc8585.jpg"><figcaption>Print and Design by <a target="_blank" href="https://makerworld.com/de/u/2953964505" rel="nofollow noopener">@adzamper7117</a></figcaption></figure></td><td><figure class="image image_resized" style="width:74.18%;"><img src="https://makerworld.bblmw.com/makerworld/draft/812382/2024-01-09_6600514d25d25.jpg"><figcaption>Print and Design by <a target="_blank" href="https://makerworld.com/de/u/1837491328" rel="nofollow noopener">@EngGraph</a></figcaption></figure></td></tr></tbody></table></figure><figure class="table" style="width:95.77%;"><table class="ck-table-resized"><colgroup><col><col></colgroup><tbody><tr><td><figure class="image image_resized" style="width:100%;"><img src="https://makerworld.bblmw.com/makerworld/draft/812382/2024-01-10_2a49647d4fde4.webp"><figcaption>Print and Design by <a target="_blank" href="https://makerworld.com/de/u/2827972142" rel="nofollow noopener">@Skovgaard</a></figcaption></figure></td><td><figure class="image image_resized" style="width:86.21%;"><img src="https://makerworld.bblmw.com/makerworld/draft/812382/2024-01-10_93d6c2a831c3.jpg"><figcaption>Print and Design by <a target="_blank" href="https://makerworld.com/de/u/4228581023" rel="nofollow noopener">@jacob.simmons52</a></figcaption></figure></td></tr></tbody></table></figure><figure class="image image_resized" style="width:97.2%;"><img src="https://makerworld.bblmw.com/makerworld/draft/812382/f2611a50-b0a0-11ee-a59a-ad068eadc082.jpg"><figcaption>Print &amp; Design by <a target="_blank" href="https://makerworld.com/en/u/2873677700" rel="nofollow noopener">@AndyF_CH</a></figcaption></figure>&nbsp;<figure class="table"><table><tbody><tr><td><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/812382/2024-01-12_9151a7b941c7f.jpg"><figcaption>Print &amp; Design by <a target="_blank" href="https://makerworld.com/en/u/746945106" rel="nofollow noopener">@surpriselady320</a></figcaption></figure></td><td> </td></tr></tbody></table></figure>

Wine Bottle Holder

Wine/Alcohol 

eatrix

Planter “Mother and Child”&nbsp;This might be a perfect gift for your mother (or significant other) to show them, that you appreciate their love.&nbsp;Bigger head size is about 100 mm (3.94 inch) diameter, smaller ~ 80 mm (3.15 inch). It should be fine to scale bigger.&nbsp;For this model I chose Bambulab strength profile, because external wall speed is slower and it model looks better on some filaments.It adds a little bit extra time (about 40min), but I think it&#39;s worth it.&nbsp;This model needs some support on arms, model is presliced with tree supports.I like to print these planters with fuzzy skin turned on (contour, fuzzy skin distance - 0.3, fuzzy skin thickness - 0.1).It can be printed smooth also, just be sure to check if seam is placed at Back/Rear.&nbsp;When planting cactus or succulents at the bottom I add a little bit of pebbles for drainage and then potting soil.And don&#39;t forget to water it according to your plant needs :)&nbsp;You can find other similar People planters at my profile:&nbsp;<img class="image_resized" style="width: 22.02%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000453527/design/2024-05-15_4a3cf01211066.jpg"><img class="image_resized" style="width: 22.09%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000453527/design/2024-05-15_40783516be3fa.jpg"><img class="image_resized" style="width: 22.03%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000453527/design/2024-05-15_8f7aeaa76f35c.jpg"><img class="image_resized" style="width: 22.08%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000453527/design/2024-05-15_34f1c79972c7e.jpg">

Planter "Mother and Child"

Today

Alexandre Paixao

Simple game Dama.&nbsp;2 players

Kit Card Table game - Dama

Kit Cards

Justin Yu

This is a remix of the original HSW located here: <a target="_blank" href="https://makerworld.com/en/models/16011#profileId-15092" rel="nofollow noopener">https://makerworld.com/en/models/16011#profileId-15092</a>&nbsp;This includes all the parts needed to make a fully functional honeycomb storage wall&nbsp;I also included paint holders that should fit anywhere between 20mm bottles up to 35 mm bottles&nbsp;A fun yet functional print

Honeycomb Storage Wall The Complete Edition

Honeycomb Wall

RU3D_Ruduan

Introducing our innovative 3D Printable StingRay Soap Dish model, a fusion of functionality and aquatic elegance. Inspired by the graceful movements of both manta rays and stingrays, this two-part design seamlessly combines form and utility.Crafted with meticulous attention to detail, the StingRay Soap Dish features a captivating stingray silhouette that not only cradles your soap with finesse but also ensures efficient drainage through its intricately designed stinger. Say goodbye to soggy soap and hello to a clean and dry bathing experience.But that&#39;s not all - we&#39;ve thoughtfully engineered this model for convenience and ease of use. The top part of the soap dish is easily removable, allowing for effortless cleaning and maintenance, ensuring your soap dish stays as fresh as the ocean breeze.Whether adorning your bathroom with its eye-catching design or delighting as a practical solution to soap storage, our StingRay Soap Dish brings a touch of aquatic charm to any space. Dive into a world of innovation and style with this 3D printable marvel, where functionality meets inspired design.

StingRay Soap Dish (Self Draining & Removable Lid)

Fishing/Beach

Lord

THE BEARCLAW KNIFE&nbsp;DESIGNED WITH A 100% INFILL STRONG EDGE (Download and check slicer to see)&nbsp;NEARLY NO LAYER HEIGHT ON BLADE ALSO!!!!!!&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;

THE BEARCLAW KNIFE

喵武士

I used to think that it was impossible to print a usable normal-sized click pen structure through a 3D printer. Bambu printer with a 0.2mm nozzle, and its accuracy is indeed a bit surprising to me.&nbsp;我曾经觉得使用3D打印机实现一个正常大小的按压式圆珠笔的结构，这是不可能的。拓竹配0.2mm的喷嘴，这个精度确实有点让我惊讶!&nbsp;&nbsp;As a 3D printing enthusiast, it&#39;s cool to have a nice 3D printed ballpen. This is a pure 3D printed retractable ballpen, with a lovely rounded shape.&nbsp;The printing accuracy is key to the mechanism of the click pen. So it should use a 0.2mm nozzle, and with 0.1mm Layer height. Two plates are suggested for better quality.&nbsp;It uses Uniball UMR-85N / UMR-83N as refill. and it only need a common (0.4*5*21) spring for ball pen.&nbsp;按压式圆珠笔的机械结构，曾使我非常着迷。作为一个3D打印的爱好者，如果有一只这样的3D打印圆珠笔，应该是一件很酷的事。&nbsp;这支笔有着圆滚滚，胖墩墩的可爱外形，长度只有12厘米，比普通的圆珠笔还短将近3厘米，携带也很方便。&nbsp;打印精度是按压式圆珠笔能否丝滑的关键，所以这里要使用0.2mm的喷嘴，层高设置为0.1mm。建议零件和外壳分别使用两块板布局以提高质量。&nbsp;笔芯使用三菱Uniball UMR-85N/UMR-83N。只需要一个0.4*5*21的圆珠笔弹簧。&nbsp;&nbsp;To make it more special, with Bambu studio text shape function, you can easily customize your name or any text to be engraved on your pen. It can be printed well using a 0.2mm nozzle.&nbsp;为了让这支笔更加特别，使用拓竹切片软件的文字功能，你可以很方便的在笔夹或笔身上定制文字，例如你的名字或送给朋友的祝福短语。使用0.2mm的喷头，可以很好地打印出这些细节。&nbsp;<img class="image_resized" style="width: 100%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437435/design/2024-05-10_06fadbcfe9b.jpg">&nbsp;&nbsp;<img class="image_resized" style="width: 49.1%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437435/design/2024-05-10_d575df089e165.png"><img class="image_resized" style="width: 49.75%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437435/design/2024-05-10_f748b01859525.png">&nbsp;<img class="image_resized" style="width: 49.24%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437435/design/2024-05-10_4f9946db4871d.png"><img class="image_resized" style="width: 49.45%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437435/design/2024-05-10_6fb63daecf2e2.png">&nbsp;<img class="image_resized" style="width: 49.28%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437435/design/2024-05-10_82c61d45d2ec7.png"><img class="image_resized" style="width: 49.2%" src="https://makerworld.bblmw.com/makerworld/model/DSM00000000437435/design/2024-05-10_e571281002fcc.png">&nbsp;Assemble details in English, pls refer to:  https://youtu.be/bVQpvxSBjMw&nbsp;<figure class="media"><oembed url="https://www.bilibili.com/video/BV1Hw4m1U7pg/?vd_source=702a082a87a60dd32752c0347b4efee5"></oembed></figure><figure class="media"><oembed url="https://www.bilibili.com/video/BV1xs421N7dL/?vd_source=702a082a87a60dd32752c0347b4efee5"></oembed></figure>

Retractable Ballpen Click Pen 按压式圆珠笔

0.2 Nozzle 

BewareDeathclaws

Based on the Thingiverse model, utilized Sloop &amp; Super Glue to put the pieces together for the Axe. Also, didn&#39;t realize until halfway through the prints I can cut parts in the slicer (so please feel free to modify these models to better utilize filament usage). I bought the LED Lights, a chargeable battery, the cables as well as the magnetic connections. I drilled out a hole and glued one of the magnetic USB pieces so it won&#39;t pop out. I included one of the parts to print for the holes that I didn&#39;t need to for the magnetic charging.&nbsp;Feel free to reach out for any additional information or recommendations

Leviathan Axe (Light up)

Mittelpunkt Studios

Simple Vent Clip for your car. I use dryer sheets infused with various scents.Cut them in half, roll them up and stuff them into the holder.&nbsp;The text is editable in Bambu Studio, or can be removed.&nbsp;Printed in Bambu ASA.

Car Refreshener Dryer Sheet Clip

House Stuff

RP47 Designs

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm200mm x 200mm.&nbsp;You can complete this print without an AMS. Use the profile that says NO AMS and it will pause at the correct height instead of doing a filament change. At that point you change your filament and let it continue until the next pause where it will wait for the next manual filament swap. This being a three color Hueforge, it will require two pauses with manual filament changes.&nbsp;&nbsp;Filaments Used: PLA+ Sunlu Black Transmission Distance: 0.6 PLA+ Sunlu Grey Transmission Distance: 2 PLA+ Sunlu White Transmission Distance: 5&nbsp;Swap Instructions: Start with Black At layer #5 (0.48mm) swap to Grey At layer #9 (0.8mm) swap to White for the rest.

Medieval Town Art Hueforge NO AMS Needed

Hueforge 

Black Glovz

Gun Ghost Keychain

Games

tufactoria3d

This is my design of a sandclock using the software HUEFORGE. Perfect for a gift or decor your room. This file is suitable for all printers (not only bambu). in case you don´t own a Bambu, just take care of the layers height in order to make de filament change.Please print at 0.08 layer height. The file also includes the .amf with all the color changes but also here you have the note:&nbsp;Swap Instructions (Just in case you want to make the filament changes manual): Start with Black (xyzfilaments) At layer #5 (0.52mm) swap to Dark Gray (xyzfilaments) At layer #9 (0.84mm) swap to Light Gray (xyzfilaments) At layer #14 (1.16mm) swap to White (xyzfilaments) for the rest.

Sandclock HUEFORGE

Michaela

Ruvim KUB

<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/853255/2024-02-08_84e04bfac95a6.jpg"></figure>&nbsp;Excited to introduce the third version of the toothpaste stand.&nbsp;Over the years, my skills have grown, and the print quality has improved. Modern printers are much more precise and allow for printing non-disassembled designs with movable parts. As a result, after several prototypes, I&#39;ve created a fully functional stand that prints in one go and requires no supports.&nbsp;In this version, I fixed the errors from the previous one and, upon numerous requests, added a gear mechanism to prevent the toothpaste from rolling back.&nbsp;There are many similar stands out there, but I settled on this one for several reasons. Perhaps the main one is the ability to always place the toothpaste vertically. It takes up less space and is much more convenient to use.&nbsp;With the gear mechanism, the toothpaste is always neatly tightened, allowing it to stand upright without leaning.I printed several of these stands in <a target="_blank" href="https://us.store.bambulab.com/products/pla-matte-filament" rel="nofollow noopener">PLA Matte </a>plastic, and the result turned out very good.&nbsp;<h4>Please note that there are two variants of the wand and you can choose which variant you prefer.</h4><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/853255/2024-02-11_c2ec7d526caca.jpeg"></figure>&nbsp;<h3>It turns out that a lot of people don&#39;t know how to properly tuck toothpaste into a toothpaste holder. Here are some photos that clearly show it.<img src="https://makerworld.bblmw.com/makerworld/draft/853255/2024-02-07_79754a67bfa61.webp"><img src="https://makerworld.bblmw.com/makerworld/draft/853255/2024-02-07_82fcf61ed91b9.webp"></h3>&nbsp;And also I would like to tell you that I recently started a small store on <a target="_blank" href="https://www.etsy.com/shop/3dkub" rel="nofollow noopener">Etsy.com</a> here will appear instrementy and exclusive projects that will not be in the open access.&nbsp;<h3><a target="_blank" href="https://www.buymeacoffee.com/ruvimkub" rel="nofollow noopener">If you would like to express your gratitude you can do so here. </a></h3>&nbsp;Also, a project <a target="_blank" href="https://makerworld.com/en/u/2356513235" rel="nofollow noopener">Organizer for Philips Sonicare toothbrushes</a>. has recently appeared, which you can find at this link.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/853255/2024-02-12_b6dba00770d77.jpg"></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/853255/2024-02-17_d1b4c628ad18b.jpg"></figure><h2><img src="https://makerworld.bblmw.com/makerworld/draft/853255/2024-02-17_d30a549263f3.jpg">My some other things:</h2><figure class="image"><a href="https://3d.ruvim.info/thingiverse" target="_blank" rel="nofollow noopener"><img src="https://3d.ruvim.info/thing.jpg"></a></figure><a target="_blank" href="https://makerworld.com/en/models/151492#profileId-165387" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/853255/2024-01-21_140ed1f4e28fc.jpg"></a><a target="_blank" href="https://makerworld.com/en/models/149624#profileId-163286" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/853255/2024-01-21_c9f371a901922.jpg"></a><a target="_blank" href="https://makerworld.com/en/models/135080#profileId-146564" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/draft/853255/2024-01-11_f09984058f1de.jpg"></a><img src="https://3d.ruvim.info/0450.png"><a target="_blank" href="https://www.thingiverse.com/thing:4968267" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Auto-Solder-Feeder-V1.1.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4934874" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Magnetic-mount-for-Street-style-Clocks.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/133763#profileId-145135" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Rectangular-stand-for-cotton-buds-and-disks.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4872540" rel="nofollow noopener"><img src="http://things.ruvim.info/img/phone-clip.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4860781" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Anex-sport-Min.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/97564#profileId-104137" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Stand-for-toothpaste-V2.0.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/105242#profileId-112325" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Stand-for-cotton-swabsticks-and-discs-V5.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4751509" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Smart-faucet-on-Arduino-(filter-resource-counter).jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/133785#profileId-145164" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Organizer-for-3D-printer.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4709801" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Acetone-Bath-on-Magnets.jpg"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4689514" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Case-for-rfid-tags.jpg"></a> <a href="Nozzle-Box.jpg" rel="nofollow"><img src="http://things.ruvim.info/img/Nozzle-Box.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/127746#profileId-138242" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Table-Adjustment-Knob-M3.jpg" alt="Table Adjustment Knob M3"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4539243" rel="nofollow noopener"><img src="http://things.ruvim.info/img/PCB-Etching-Tray.jpg" alt="PCB Etching Tray"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4495533" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Speed-Controller-220V.jpg" alt="Speed Controller 220V"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4458304" rel="nofollow noopener"><img src="http://things.ruvim.info/img/M%D0%BEdular-Mini-Circular.jpg" alt="Mоdular Mini Circular"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4383145" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Clock,-Counter-Subscribers..jpg" alt="Clock, Counter Subscribers."></a> <a target="_blank" href="https://www.thingiverse.com/thing:4361811" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Compass---Plotter.jpg" alt="Compass - Plotter"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4356203" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Phone-Clip..jpg" alt="Phone Clip."></a> <a target="_blank" href="https://www.thingiverse.com/thing:4327360" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Phone-Stand.jpg" alt="Phone Stand"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4317738" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Mini-Grinder.jpg" alt="Mini Grinder"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4304240" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Disc-Sander-Duo.-D50mm,-D75mm.jpg" alt="Disc Sander Duo. D50mm, D75mm"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4265679" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Lifting-Gear-For-Automatic-Nozzle-Cleaner.jpg" alt="Lifting Gear For Automatic Nozzle Cleaner"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4216312" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Mini-electric-lighter.jpg" alt="Mini electric lighter"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4212059" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Stand-for-toothpaste.jpg" alt="Stand for toothpaste"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4123230" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Camera-Weight-for-Diving.jpg" alt="Camera Weight for Diving"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4099456" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Electric-lighter.jpg" alt="Electric lighter"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4086763" rel="nofollow noopener"><img src="http://things.ruvim.info/img/The-best-soldering-iron-stand.jpg" alt="The best soldering iron stand"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4056390" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Flux-stand.jpg" alt="Flux stand"></a> <a target="_blank" href="https://www.thingiverse.com/thing:4084435" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Mobile-Hard-Drive:-2.5-Inch-USB-3.0-SATA.jpg"></a> <a target="_blank" href="https://makerworld.com/ru/models/118219#profileId-127104" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Magnetic-plate-for-little-things.jpg" alt="Magnetic plate for little things"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3970160" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Clamp-for-firmware-controllers-6-pins.jpg" alt="Clamp for firmware controllers 6 pins"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3976187" rel="nofollow noopener"><img src="http://things.ruvim.info/img/2-relays-box-or-ESP-01-with-relay.jpg" alt="2 relays box or ESP-01 with relay"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3970750" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Case-for-Ndemcu.jpg" alt="Case for Ndemcu"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3942946" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-A-B-C-D-E.jpg" alt="Alphabet for children. A B C D E"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3946878" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-F-G-H-I-J.jpg" alt="Alphabet for children. F G H I J"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3974764" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-K-L-M-N-O.jpg" alt="Alphabet for children. K L M N O"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3989549" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-P-Q-R-S-T.jpg" alt="Alphabet for children. P Q R S T"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3991721" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Alphabet-for-children.-U-V-W-X-Y-Z.jpg" alt="Alphabet for children. U V W X Y Z "></a> <a target="_blank" href="https://www.thingiverse.com/thing:3912631" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Replacement-SD-Card-Case.jpg" alt="Replacement SD Card Case"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3914719" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Solder-feeder.jpg" alt="Solder feeder"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3851649" rel="nofollow noopener"><img src="http://things.ruvim.info/img/USBasb-case.jpg" alt="USBasb case"></a> <a target="_blank" href="https://www.thingiverse.com/thing:3845727" rel="nofollow noopener"><img src="http://things.ruvim.info/img/Magnet-stick.jpg" alt="Magnet stick"></a>&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;

Stand for Toothpaste V3.0

Print Now

PrintMint

Bring the captivating beauty of Stormy Dreams into your living space with our DIY Wall-Mounted Cloud Night Light. Crafted for both simplicity and enchantment, this unique night light assembly seamlessly combines a 3D printed Cloud and Lightning Plate with a battery-powered LED light, allowing you to create your own magical stormy scene on the wall.&nbsp;<a target="_blank" href="https://patreon.com/PrintMint?utm_medium=unknown&utm_source=join_link&utm_campaign=creatorshare_creator&utm_content=copyLink" rel="nofollow noopener">Support me on Patreon if you like my work or want a commercial license.</a>&nbsp;You can probably use a similar LED but here is the one I used.The LED kit for this is linked here:https://www.amazon.com/dp/B0C3LZR1FX?psc=1&ref=ppx_yo2ov_dt_b_product_details

Stormy Dreams: Cloud Night Light w/ Lightning Bolt

Night Lights

Wing-Art

U P D A T E 3 1 . 3 . 2 0 2 4 - T H I S    V E R S I O N    I S    O U T D A T E D !&nbsp;<a target="_blank" href="https://makerworld.com/en/models/406101#profileId-307995" rel="nofollow noopener">!!! PLEASE DOWNLOAD VERSION 2.0 with QUICKLOCK MOUNT HERE !!!</a>  __________&nbsp; Universal Kitchen Dispenser for Pickle Jars (80 mm Diameter) &amp; Mason Jars&nbsp;This print file contains the design for a universally applicable kitchen dispenser, specifically developed for use with pickle jars with a diameter of 80 mm or Mason Jars.  Excellent for storing and easily dispensing various ingredients such as:  <ul><li>Coffee</li><li>Cereal</li><li>Rice</li><li>Cat food</li><li>Pasta</li><li>Lentis</li></ul>…or many other things! Furthermore, a Jar for self-printing is included in the Pickle Version!&nbsp;Design Features:<ul><li>Flap with Rubber Ring: At the bottom of the dispenser, there is a flap operated by a cleverly integrated rubber ring mechanism.</li><li>Versatile Use: The dispenser is ideal for a variety of dry foods such as coffee beans, cereal, rice, pasta, lentis and other dry ingredients.</li><li>Text Plates: Additionally, the kitchen dispenser can be equipped with text plates for labeling.</li></ul>&nbsp;Note - There are two Versions of the Dispenser:   <ul><li>Pickle Jar Version for 80mm Diameter</li><li>Mason Jar Version (als requested in the comments)  </li></ul>The printable Jars: Please note that the printable jars are only compatible with the &#39;Pickle&#39; version of the Dispenser!<ul><li>Sizes: Two options - 800ml and 2500ml for self-printing.</li><li>Print Profiles: Independent profiles for Vase Mode (translucent prints) and normal prints (solid and robust).</li><li>If you need a Lid: Available <a target="_blank" href="https://makerworld.com/de/models/96064#profileId-102443" rel="nofollow noopener">HERE</a>.</li></ul>&nbsp;It is highly recommended to print the included test thread before printing the main parts - except you print the included Jar (Pickle Version)! This is to ensure that the thread fits correctly and that the jar is compatible with the dispenser.<a target="_blank" href="https://all3dp.com/2/food-safe-filament-brands-compared/" rel="nofollow noopener">HERE</a> you can find the Best Food-Safe PLA Filaments of 2023. Special bonuses:&nbsp;Additional doors:<ul><li>10mm handle (Standard size)</li><li>20mm handle</li><li>30mm handle</li></ul>Adapter:<ul><li>Pickle-Jar Version to → Wide Mouth Mason Jar (86mm)</li></ul> Just take a look at my other Kitchen Tools here:<ul><li><a target="_blank" href="https://makerworld.com/de/models/96064#profileId-102436" rel="nofollow noopener">Printable Jars (compatible with this Kitchen Dispenser!)</a></li><li><a target="_blank" href="https://makerworld.com/de/models/96912#profileId-103376" rel="nofollow noopener">Orange Peeler Citrus Pro</a></li><li><a target="_blank" href="https://makerworld.com/de/models/99747#profileId-106354" rel="nofollow noopener">EGG-citing Nest - the classic Egg Cup</a></li><li><a target="_blank" href="https://makerworld.com/de/models/115132#profileId-123776" rel="nofollow noopener">Bottle-Can Dispenser</a></li><li><a target="_blank" href="https://makerworld.com/de/models/100260#profileId-106926" rel="nofollow noopener">Knife Cat Napkin Holder</a></li><li><a target="_blank" href="https://makerworld.com/de/models/109348#profileId-116818" rel="nofollow noopener">Hexagon Napkiin Holder</a></li></ul>

Kitchen Dispenser for Jars (included!)

Kitchen

Nardo3D

Beware of immitators!  This is the ORIGINAL Modular Mini-Golf game on MakerWorld!&nbsp;The most important part of working in an office is avoiding doing actual work! Procrastinate all day long with Nardo's Modular desktop mini-golf set! Arrange dozens of tiles to create unlimited unique miniature golf holes.&nbsp;Featuring a grid-based modular design (heavily inspired by the Gridfinity system-but much smaller). Includes nearly two dozen unique tiles, with more to come in the future!&nbsp;Putter is designed to fit on the end of a standard Bic “Round Stic” style pen.&nbsp;UPDATE 1/24/2024 - Updated tile quantities based on feedback & testing, as well as a more robust putter design! Ball not included - I recommend a 9 to 10 mm plastic ball bearing (easily found on Amazon) or you can try printing a 10mm sphere.&nbsp;Tip: A vacuum pen (example: <a target="_blank" href="https://www.amazon.com/YXQ-Vacuum-Sucking-Suction-headers/dp/B07MLW5TKP" rel="nofollow noopener">https://www.amazon.com/YXQ-Vacuum-Sucking-Suction-headers/dp/B07MLW5TKP</a>) makes lifting the flat tiles a breeze!&nbsp;Choking Hazard! Small parts, not for children under 3!

The ORIGINAL Modular Desktop Mini Golf Set

Work

Sevro

OverviewA shell-shaped pot on a bonsai tree. I was inspired by this photo and decided to make some similar ones.<figure class="image image_resized" style="width:214.406px;"><img src="https://media.printables.com/media/prints/550656/rich_content/7fb09307-eef0-40af-9b48-1e5503550fbe/shell.jpg"></figure>&nbsp;InstructionYou have two option to print this model.<ol><li>You can print separately tree and shell. This method allow you to color each part as you want. However you have to use support to print shell. After print put shell into tree. You can also glue it but it is not necessary.</li><li>You can print whole model at once (I didn't test it yet)</li></ol>Have fun

Shell-shaped pot on a bonsai tree

Flower Pot

ShimaArchi

6 parts, no support needed, no glue

Piston Cup

Atreus

Smarty

Oni Mask

Masks

cartyski

Struggling to open jars of all shapes and sizes? Say goodbye to stubborn lids with this jar opener designed to fit them all!

OPENSESAME3000 - Jar Tool

Tools

Matthew Ghost

The stand provides a stable support for your mobile phone, making it easier to watch videos, make video calls, read recipes, and much more. It's a perfect fit for your desk, bedside table, or anywhere else you need to keep your phone visible and within reach

MOBILE PHONE STAND CAT, DESK STAND/HOLDER, UNIVERSAL-IPHONE,ANDROID, TABLET

Pets

Jonneha

The phone holder works with all kinds of standard pop sockets.&nbsp;Place the back side of the socket against the buildplateRequires the use of support material. (Touching buildplate only)Designed for 0.16 mm layer heightNotch on the back for double-sided tape. (1.1 mm) Printed in PETG

Popsocket Holder

Phone Accessories 

Augustas

<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000136916/design/2024-03-23_e3aef21a74483.png"></figure>&nbsp;<a target="_blank" href="https://www.buymeacoffee.com/augustas" rel="nofollow noopener">https://www.buymeacoffee.com/augustas</a>&nbsp;This stylish and functional 3D printed car trash can is the perfect way to keep your car clean and organized. The sleek design features a patterned side panel and a movable lid flap for easy trash disposal. It can also be used as a desk trash can.Features:<ul><li>Stylish and functional design</li><li>Patterned side panel adds a touch of personality</li><li>Movable lid flap for easy trash disposal</li><li>Can be used as a car or desk trash can</li><li>Easy to print and assemble</li></ul>Printing Instructions:<ul><li>Recommended filament: PLA or PETG (with a 0.2mm nozzle)</li><li>Layer height: 0.2mm</li><li>Infill: 20% (or higher for a more durable trash can)</li><li>Support material: Not required</li></ul>Enjoy your new 3D-printed car trash can!&nbsp;!! This is my model I created it following Brandon Santana YouTube tutorial, I Added some details and made it fit more loosely. But it is still my own design please do not flag this as a copyright!!Link to the tutorial : <a target="_blank" href="https://youtu.be/ci4JB_NZ7ks?si=zwvmFfeb0jTwzHsA" rel="nofollow noopener">https://youtu.be/ci4JB_NZ7ks?si=zwvmFfeb0jTwzHsA</a>.

Car Trash can

Car Accessories 

APlus3dDesigns

This is a custom clock i designed for a charity fundraiser. It is ment to hold and display your articulated flexible dragons up to 19". Larger ones may work, but i have yet to test it.&nbsp;Clock workings were found on Amazon. They are like $12 for 4 sets.<a target="_blank" href="https://www.amazon.com/dp/B0B3CSGHTW?ref=ppx_yo2ov_dt_b_product_details&th=1" rel="nofollow noopener">https://www.amazon.com/dp/B0B3CSGHTW?ref=ppx_yo2ov_dt_b_product_details&th=1</a> As for the dials, i made the ones included where the clock is smaller and ment for a shelf or mantle.

Articulated Dragon Clock

Clocks 

3DJPDESIGNS

Created this cute mushroom that I hope you guys will adore as much as I did! File as a 3MF file for you to multicolour print too <3 Hope you guys like it! There is also a file which is not a planter for just decour! Which can be hella cute as mini mushrooms <3 !!! Print is completely SUPPORT LESS FOR PERSONAL USE ONLY IF INTERSTED IN SELLING THEM CONSIDERING SUBSCRIBING TO MY PATREONLINK : <a target="_blank" href="https://www.patreon.com/user?u=339505" rel="nofollow noopener">https://www.patreon.com/user?u=339505</a> Being a Patreon will get these files for free every month ^-^Consider following me on Instagram for more updates ! <a target="_blank" href="https://www.instagram.com/3djpdesigns/" rel="nofollow noopener">https://www.instagram.com/3djpdesigns/</a>Created to bring some fantasy into your work place !Note: This design has been created as ORIGINAL ART

Cute Mushroom Planter / Plant Pot / Desk Organizer / Pencil Holder 

Mushrooms

Bencham95

Ghost vase inspired by a balloon under a sheet, i made for the vase contest. Thought as of the timing id make something to do with Halloween. Print SettingsVase Mode0.16 - 0.2 layer heightThe opening of the vase will depend on how steep of an overhang your printer / slicer setting will allow. &nbsp;If you like please show some support and buy me a coffee!https://www.buymeacoffee.com/bchambro

Ghost Vase (Vase Mode) Halloween decoration

Spooky 

mclanesmemories

Set of 3 bookmarks showing death and life intertwined. Skeletons with flowers.&nbsp;Please share your prints&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm&nbsp;Swap Instructions: Start with Black At layer #4 (0.40mm) swap to blue At layer #8 (0.72mm) swap to pink At layer #12 (1.04 mm) swap to white

Set of 3 Bookmarks - Face of death and life returns - skeleton and flowers

Bookmarks 

Kevbot.

When your friends visit, they'll be impressed with this coaster 😀.&nbsp;Shaped like a beautiful flower, with links between each petal. This flower coaster can bend and flex a bit, making it a unique table piece. It's print in place and is big enough to hold most cups and cans.&nbsp;This model is for PERSONAL USE ONLY, if you want a commercial license and access to more awesome models you can get it on my patreon <a target="_blank" href="https://www.patreon.com/kevbot_3d" rel="nofollow noopener">https://www.patreon.com/kevbot_3d</a>&nbsp;Like with all my models, I went through many iterations to make sure it was strong, and easy to print without supports.&nbsp;Please feel free to share images of your prints on this page, I would love to see them.&nbsp;Thank you for the support, and I hope you love the Coaster! Let me know if you would like to see any other coaster designs! Happy Printing!&nbsp;Sincerely,Kevin&nbsp;ALL KevBot. designs are protected by Copyright Law. When you purchase, you do NOT have the right to sell any digital file or printed model of my designs without my explicit written consent.

ARTICULATING FLOWER COASTER!

Flower

Remixx

A simple vase easy to print with the A1 mini.It's almost the maximum size for the printer.Enjoy !

Vase twist wave A1 mini

Vases

dugy58

I made this in Tinkercad and Fusion 360.

Articulated Pot Leaf

Cannabis

NUKDDD

Cut the cord with the <a target="_blank" href="https://makerworld.com/en/models/233562#profileId-250197" rel="nofollow noopener">alternate base that uses a battery powered puck light designed by Tawpie</a>.&nbsp;Meet Felix, the Flexi Shroom 🍄 a mushroom lamp for Bambu Lamp Kit 001 and tea lights up to 39mm diameter. Easy to print, no supports, and A1 mini compatible. &nbsp;You can support me by purchasing <a target="_blank" href="https://amzn.to/3PApWSp" rel="nofollow noopener">The lights </a>I used from this link. I may earn a small commission.&nbsp;<a target="_blank" href="https://shrsl.com/4gf88" rel="nofollow noopener">Designed to fit Bambu Lab's Lamp Kit, available in the online shop.</a>&nbsp;Printed with Bambu's <a target="_blank" href="https://shrsl.com/4gfvl" rel="nofollow noopener">Basic</a> and <a target="_blank" href="https://shrsl.com/4gfae" rel="nofollow noopener">Matte PLA</a>&nbsp;Please give a 👍 if you like it, even if you don’t download it, it’ll help others discover it 😊&nbsp;The mushroom cap is flexible, so when it sits on the stump, it'll sag a little and give it a more natural look, and you can fidget with it as well.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/748230/2024-01-29_f8209c9a8e82a.jpg"></figure>The base comes in 2 flavors, 1 is for the lamp kit, it screws on to the stump, and don't forget to use the diffuser discs to make it less blinding. Like my other mushroom lamps, the top is interchangeable with <a target="_blank" href="https://makerworld.com/en/models/95343#profileId-101704" rel="nofollow noopener">Stumpy</a> and <a target="_blank" href="https://makerworld.com/en/models/127134#profileId-137541" rel="nofollow noopener">Shady</a>, you can even screw on <a target="_blank" href="https://makerworld.com/en/models/86208#profileId-92095" rel="nofollow noopener">Teeny</a>, <a target="_blank" href="https://makerworld.com/en/models/160662#profileId-176353" rel="nofollow noopener">Cactus</a> and <a target="_blank" href="https://makerworld.com/en/models/124690#profileId-134681" rel="nofollow noopener">Lucky</a> if you want, but it works best with my mushroom caps.&nbsp;Disclaimer: This model is part of the Creator Program, When you purchase the Lamp Kit 001 or filament through the links provided, creators may earn an affiliate commission as a reward of their work. (The creator program is currently in the trial phase. The application is not yet open to public.)

Flexi Mushroom Lamp 

Lamps

PRINT3DGIFTS

Made this perfect fit for the Bambu Lab A1 Mini. Prints without support and only takes one plate! Enjoy and don't forget to post your makes!

T-Rex Skull A1 Mini perfect fit!

Skulls

cruse2382

includes 2 versions 1 for full size printers and one for the a1 mini.&nbsp;full size version is 20cm long and 14cm wide and 14cm tallA1 mini version is 18cm long and 14cm wide and 14cm tall which i found a tad shorter than my books but still works fine&nbsp;If using raw files I would recommend printing the actual holder on its side (like in the image) as i ran into issues printing it lay flat.&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/279012/2023-12-16_4aa157ce0ba4c.png">&nbsp;the drawer cavity is around 40mm tall and there is a small tab at the back to stop the drawer sliding all the way through.

Book Holder with drawer a1 mini compatible 

Desk Items

wadecbr

Its just a sign. Thanks for looking.

High Speed Wireless Devices Sign

Flat Signs

FilliFuu

Cute baby dragon bracelet, multiple profiles including A1 mini with various sizes for adults or children.All print in place without supports and that's it. Carefully open the mouth to use the link.Avoid using silk for the mouth as silk is rather weak.&nbsp;Enjoy.