3D Endeavors

YelTrik Designs - Click FOLLOW

<h3>THE ORIGINAL AND STILL THE BEST!</h3><h3>Buffer Right-Side PTFE Guide (No Spool Arm Version)</h3>The original simple guide keeps your PTFE tube properly aligned and secure. Don't be fooled by copies! This guide accurately aligns the PTFE tube as it exits the Buffer and enters the Guide. The guide then starts the gradual arc of the PTFE tube so it enters the printer with the least filament resistance possible. This is the last leg of PTFE tube before entering the chamber. If your filament got this far keep it on track to get the job done. &nbsp;WARNING: There are copies of my original design. However, they don't understand the physics behind this guide. They continue the PTFE horizontal through the entire guide. This delays the PTFE tube from starting the arc to the chamber which makes the radius of the tube tighter than Bambu Lab designed and increases filament friction. My design perfectly aligns the PTFE tube horizontally from the buffer then creates the precise radius/arc to reduce filament friction to the chamber. This is the original and best solution for the last leg of your filament path. Don't settle for poorly designed copies. &nbsp;Simple, fast and very little filament. It's a must have item for keeping your prints from failing due to some feed or pull back issue.&nbsp;NOTES: <ul><li>This version is installed without the stock spool arm. If you have the stock spool arm installed check out my other version.</li><li>By design the guide for the PTFE tube is oversized to accommodate the movement of the PTFE tubes movement from the Filament Buffer.</li><li>See Installation notes below</li></ul>CHECK OUT THESE OTHER PTFE ACCESSORIES<h2><a target="_blank" href="https://makerworld.com/en/models/53665#profileId-55391" rel="nofollow noopener">AMS Buffer PTFE Holder</a></h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/276856/2023-11-02_31f608e11f18d.jpg"></figure><h2> </h2><h2><a target="_blank" href="https://makerworld.com/en/models/52297#profileId-54481" rel="nofollow noopener">AMS Filament Pull Back Fix</a> </h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/276856/2023-10-30_4c232e2109bc6.png"></figure><h2> </h2><h2><a target="_blank" href="https://makerworld.com/en/models/33060#profileId-29778" rel="nofollow noopener">PTFE Chain Clips</a> </h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/276856/2023-10-30_ebb2ea691cbdd.png"></figure><h2> </h2><h2><a target="_blank" href="https://makerworld.com/en/models/27398#profileId-23810" rel="nofollow noopener">AMS Filament Buffer Release Button</a></h2><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/276856/2023-10-30_0bd3c9f1abb9c.png"></figure>&nbsp;<h2><a target="_blank" href="https://makerworld.com/en/models/43257#profileId-44460" rel="nofollow noopener">PTFE Guard - Print Head</a></h2>&nbsp;<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/276856/2023-10-30_70b0b6bd55b2f8.png"></figure>&nbsp;&nbsp;INSTALLATION;<ul><li>Remove the PTFE tube from the PTFE connector at the top of the printer</li><li>Remove the stock spool arm if it is not already removed</li><li>Route the PTFE tube through the guide</li><li>Install the guide with the screws from the stock spool arm</li><li>That's it!</li></ul>&nbsp;&nbsp;

AMS Buffer Output Side PTFE Alignment Guide

Teixi3D

I bring you a painted style Super Mario model, created with HueForge. I hope you like it!!&nbsp;Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mmFilaments Used: PLA PolyTerra Charcoal Black Transmission Distance: 0.3 PLA PolyTerra Pastel Watermelon Transmission Distance: 1.5 PLA PolyLite Pro Light Blue Transmission Distance: 1 PLA Protopasta White Transmission Distance: 3Swap Instructions: Start with Charcoal Black At layer #7 (0.64mm) swap to Pastel Watermelon At layer #15 (1.28mm) swap to Light Blue At layer #22 (1.84mm) swap to White for the rest.

super mario painting (HueForge)

Amao Chan

When the film spreads through the webs, it shows that a plastic straw pulled out from the poor turtle's nostrils, which used its misfortune to slightly change the world.&nbsp;Many people have begun to take the initiative about stop using the plastic straws, and some chain restaurants have no longer offer the plastic straws to their customers. As the matter of fact, it is not just straws that would harm the turtles in the ocean! Marine debris, plastic bags, fishing hooks, abandoned fishing nets, etc. also lead turtles to death. The rapid development of science and technology have created many substances that should not exist in our nature; Unfortunately, most species are not evolving fast enough to catch up with us. These sea turtles are typical examples. They don’t have enough ability to distinguish the jellyfish they love from those plastic bags that might kill them, therefore, It’s much more important that we should think about our nature when we’re trying to get anything further progressed.&nbsp;I’ve seen turtles swimming below me when snorkeling. The slow waving movement of their forelimbs looked like that they were flying under the sea, which provided the inspiration [flying sea turtle]. I took my previous origami turtle creation as a prototype, by adding more details, and used the movable mechanism to imitate the body undulating, even the relative movement of the neck and body of the sea turtle under reaction force. It is my goal to reproduce the turtle swimming gracefully under the sea! After a few weeks of hard work, I completed [flying sea turtle] automata! And I love it a lot! The design process and the final completed work bring me a lot of fun and achievements. Sincerely, I hope everyone can be delighted during the assembling.&nbsp;Thanks to SpiderMaker for sponsoring the creation of this work. Material used SpiderMaker PLA Matte Iron blue/Matte Clay/Matte Orchid Purple/Matte Brick Red/Matte Kraft Brown <a target="_blank" href="https://www.amazon.com/SPIDER-MAKER-Matte-Printer-Filament/dp/B07HX9DY9F" rel="nofollow noopener">https://www.amazon.com/SPIDER-MAKER-Matte-Printer-Filament/dp/B07HX9DY9F</a><a target="_blank" href="https://amaochan.work/" rel="nofollow noopener">https://amaochan.work/</a> <a target="_blank" href="https://www.facebook.com/paperworkers/" rel="nofollow noopener">https://www.facebook.com/paperworkers/</a><a target="_blank" href="https://youtu.be/Y04A6KfLbRo" rel="nofollow noopener">https://youtu.be/Y04A6KfLbRo</a> <a target="_blank" href="https://youtu.be/mZWQ2mEQNc4" rel="nofollow noopener">https://youtu.be/mZWQ2mEQNc4</a>&nbsp;Print suggestions 1.Layer height 0.2mm 2.Low down the flow to 90%or 95%. 3.Add raft. 4.Add oil on moveable parts. 5.Replace old parts with new parts which is added "-NEW" after the original part name. 6.Part "FT-GEAR02" is advised to print in layer height 0.1mm or 0.15mm,and it needs support.&nbsp;海中飛翔的海龜 當塑膠吸管從可憐的海龜鼻孔中拔出的影片在網路中流傳，這海龜用牠的不幸，稍微的改變了這世界。許多人開始主動不使用塑膠吸管，連鎖餐廳也不再提供塑膠吸管；但是能在海洋中傷害海龜的不只是吸管！塑膠袋、魚鉤、廢棄魚網……等等，這些海洋垃圾也是能讓海龜溺死在海底的。人類的科技快速進展，創造了許多在自然中本來並不存在的物質；大部分的動物是無法適應人類的進步，海龜就是個例子，牠們還沒進化到能夠辨別，牠愛吃的水母和會害死牠的塑膠袋的差異！也許我們的進步應該更相容於自然環境，才是對的方向！&nbsp;我曾經在海上浮潛時，親眼見到海龜從我的下方游過，牠前肢緩慢的揮動，就像是在海底飛行一般，這經歴啟發了［海中飛翔的海龜］作品的創作方向。我採用多年前的創作--摺紙海龜，當成原型，並在摺紙的基礎上，增加了更多的細節；再用可動的機構，模擬海龜揮動前肢游泳、牠身體微妙起伏，及在反作用力下海龜頸部與身體的相對運動。重現海龜在海中優雅游泳，是我的目標！在幾星期的努力下，我完成了［海中飛翔的海龜］automata！我很喜歡這個作品！在設計這作品的過程與完成結果為我帶來許多的樂趣，也希望大家能在列印組合的過程中得到快樂！&nbsp;感謝 SpiderMaker 織造者 贊助本作品之創作 使用材料 SpiderMaker PLA 消光鐵灰藍色、消光陶土色、消光瓦紅色、消光蘭紫色、消光原皮色&nbsp;列印建議 1.層高0.2mm 2.流量降到90-95 3.海龜本身加基筏列印，不要支撐。 4.組裝完成後在會移動零件加些潤滑油。 5.請選用檔名有(new)的物件取代原來物件。 6.FT-GEAR02的建議層高為0.15mm或0.1mm，需要支撐。

Flying Sea Turtle

Art Projects

josteb

This is a simple yet effective design to enter in the Christmas season. I wanted my X1C to be a part of my Christmas, so I designed this Santa Hat.&nbsp;Support are needed!!&nbsp;I hope you will enjoy this design.&nbsp;23/11/23 - Added P1 Santa Hat Model&nbsp;29/11/23 - Added a NO AMS pritn profile for X1/P1&nbsp;Peace ;)&nbsp;

Santa Hat For  BambuLab X1/P1

xmas

SPStudio

<h4>I update, revise and improve my design for my fixes very often. Please only use my Print Profile (Labelled as Designer or SPStudio) to ensure this fix is updated & work well. Profile with Non-Designer tags may be of poor functionality or non updated model.</h4>Click on Like if this model helped you in some way. It is very important and will help increase the exposure of this design to more people who might need it. Cheers!&nbsp;&nbsp;This will be my final Ams internal fix as i believe there is no bettor way to fix it internally anymore. Thank you so much for your support.&nbsp;<blockquote>AnnouncementNew and Improved V2 Versions for the Ams Buffer Fix <a target="_blank" href="https://makerworld.com/en/models/101046" rel="nofollow noopener">Before Buffer</a> and <a target="_blank" href="https://makerworld.com/en/models/85989" rel="nofollow noopener">After Buffer</a> have just been released. Do check them out in my profile to see what are the improvement. Thank you for your continuous support.<figure class="image image_resized" style="width:33.04%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393216/2023-12-21_db335e9276f41.jpg"></figure></blockquote><h2> </h2><h2>Introduction</h2>Failed to pull back filament error can be caused by multiple different variables & factors. This is a part of an series of Ams fixes that i have designed which can complement each other when used together. I do suggest you install all my fixes together for the 0ptimal effect to help your filament travel properly across the entire system which in turn can help improve, reduce or remove any potential Ams errors.&nbsp;I have grouped all fixes into their respective Collection for ease of searching what to install.&nbsp;V2 Collection are improvements done on the shortcoming of V1 Collection. Feel free to try V2 Collection and if it doesn't work properly then you can try the V1 Collection. You can easily find each of the Collection by clicking on the Collections tab on my profile.&nbsp;Unfortunately there isn't a single fix that can 100% work for everyone. What works for others, may not work for you but my fixes is definately a great place to start and have worked for majority of the users. My fixes are precisely measured then modelled. A Proper Fix would have the highest chance to reduce or solve the error.&nbsp;<figure class="image image_resized" style="width:81.05%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393216/2024-01-09_cd9c426e40212.jpg"></figure><h2> </h2><h2> </h2><h2>If you are too bored to read the entire lengthy write up explaining the need for this fix, here is the TL:DR.</h2>&nbsp;What is this? Ams Filament Pull Back Fix V2 Upgraded is a total revamp design of the <a target="_blank" href="https://makerworld.com/en/models/47982#profileId-49834" rel="nofollow noopener">hugely successful previous model</a> for correcting the internal Ptfe tubes angle inside the Ams and maintain a straight Ptfe feeding into the Ams motor to reduce friction and pressure.&nbsp;&nbsp;Important Note: This new design is used to replace the older version. You can choose to use any of the version or try 1 then if it doesn't work very well then try the other one, but please DO NOT use both new and old model together. It will make things worse.&nbsp;&nbsp;Main difference with the previous model <a target="_blank" href="https://makerworld.com/en/models/47982#profileId-49834" rel="nofollow noopener">Ams Fix Failed To Pull Back Filament Error</a><ol><li>Completely New Design, even accurately designed to solve the problem compared to the original version.</li><li>Will NOT affect your warranty as its reversible.</li><li>Even well supported by the new screws design comparing to my previous fix or other similar clones trying to do a lookalike workalike.</li><li>Precise measurement for reduced friction of filament moving through</li><li>Helps reduce the internal Ptfe wear and tear</li><li>Fix is now much closer in distance to the root of the problem.</li><li>Ensuring nearly ZERO possibility or chances of the tube flexing near the entry point of the Ams internal filament hub causing that misalignment that might cause an error to pop up.</li><li>Angle of the entry for the Ptfe into the Ams internal Filament have been re-optimised once again..</li><li>ez to install, just unscrew the 2 screws at the Ams internal Filament Hub and put in the fix then put back the screws.</li><li>As the fix supporting the Ptfe is now right outside the entry of the <a target="_blank" href="https://wiki.bambulab.com/en/x1/maintenance/replace-filament-hub" rel="nofollow noopener">Ams internal filament hub</a>, possibility of failure to fix the problem because of bent or misshaped tube is now greatly reduced.</li><li>This fix have been tested for on 1 X1C, 1 P1P and 2 P1S for about 94800 retractions so far as of this listing.</li></ol>&nbsp;Please ignore the silver screw i used as seen in the install video, just use the same original 2 black screws from your internal Ams filament hub. In order to make and design and measure this fix, i rounded my own screw threads after assembling and disassembling 50 times for variations i tested against height, angle and thickness.&nbsp;Please follow the installation video closely to ensure you are installing it correctly. Failure to follow will affect how well the fix will work. Video at end of page.&nbsp;&nbsp;Who needs this fix? 1) Constantly having errors like Failed To Pull Out Filament and similar related2) The Ams motor sounds like struggling when move filament in and out of the Ams to the Extruder, like a lot of friction when moving.3) Ams cannot load or unloading properly. (Not including Spool being too light or a break of filament in the Ams)4) Having a constant struggle on any of your Ams slots, people complained about Slot 2 and 3 but this fix is designed to fix all of 4 slots for Failed To Retract / Pull Out Filament Error.&nbsp;&nbsp;Why choose this fix instead of other similarly designed fix?I do think that in theory, this new fix will work great and likely even superseding in performance when compared to my ver 1 design.&nbsp;This is ez to print but yet its measurement is very precise. I have spent over 60 hours to design and confirmed the proper angle to move the internal Ptfe to allow filament to pass through smoothly and then printed multiples models to ensure that my fix works by properly aligning the internal Ptfe tube to reduce and possibility even eliminating the dreadful Failed To Pull Out Filament Error or similar related problems.&nbsp;&nbsp;<h2>Preparation Video (Proper removal of support and ensure Ptfe tube fit)</h2><figure class="media"><div data-oembed-url="https://youtu.be/QZkzHy08jVI"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/QZkzHy08jVI" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/393216/2023-11-04_20b419972641e.jpg"></figure>&nbsp;<h2>Installation Video</h2><figure class="media"><div data-oembed-url="https://youtu.be/6rs1xp-rX5Q"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/6rs1xp-rX5Q" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>(As the location of the fix is right at the entry point of the Filament internal hub do make sure you align then push in the Ptfe Tube tightly making sure that the Ptfe tube actually entered the internal filament hub.)&nbsp;Also take note to the arrows at the side, make sure the fix is NOT clipping or pressing on any of the Ams wiring when you are installing it. <figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/393216/2023-11-05_c033df2f88abb.png"></figure>Pic from Bambu wiki.&nbsp;<h2>Important Notes:</h2>Please watch the video and description carefully. Its really important to make sure the fix installed correctly to let it work properly&nbsp;Note 1: The Ptfe Tube is supposed to be tight and snug for the support with precision. Plz make sure you installed it correctly as per the video instruction.&nbsp;Note 2: Please ensure you followed the preparation video closely before installing to ensure all supports are CLEANLY removed so the fix will work perfectly&nbsp;Note 3: You are required to properly assembled the Ams including the 2 screws that you unscrewed during the disassembly as this model require everything to be tight and snug for it to work properly.&nbsp;Note 4: When reassembling try to adjust the 2 very long wires connecting to the rear of the Ams Circuit board, don't let them press on any of the Ptfe tube. I don't think it matters but its a good practice.&nbsp;Note 5: Do NOT overtighten the screws please. As shown in the installation video, just tight then finger tight will work Don't jam it all the way down please. The screw is just to hold the fix in place.&nbsp;&nbsp;&nbsp;<h2>What Mod / Fixes / Enhancement do i offer?</h2>Please don't download the wrong one. Only those in the photos below is designed by me who painstakingly took a lot of time to measure carefully and design just to get it working. #SupportOriginal Love you guys for all the support so far!&nbsp;- <a target="_blank" href="https://makerworld.com/en/models/47982" rel="nofollow noopener">Ams FIX Failed To Retract Filament Error (a preventive measure and solve the bay 2 and 3 error and prevent bay 1 and 4 to have any possibility of having an error due to tension and friction)</a> (Updated design on the 2nd photo below, try 1 then if it doesn't works properly for you then install the other one.)&nbsp;<figure class="image image_resized" style="width:74.94%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393216/2024-01-10_2e40f9b49d622.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/56906" rel="nofollow noopener">(BRAND NEW) Ams Filament Pull Back Fix V2 Upgraded - Completely New Design Upgrade For Ams Filament Pull Back ERROR! Precisely Measured</a>&nbsp;<figure class="image image_resized" style="width:75.86%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393216/2024-01-10_9c729f1a3501a.webp"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/52782" rel="nofollow noopener">- Ams Buffer Fix For Failed To Pull Back Filament Error (reduce wear on the external Ptfe tube and allow the most smooth, least friction angle to go into the Ams buffer thus reducing the possibility of an error popping up)</a>&nbsp;<figure class="image image_resized" style="width:75.68%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393216/2024-01-10_14c8811c47696.webp"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/101046" rel="nofollow noopener">- V2 Ams Buffer Fix For Failed To Pull Back Filament Error (reduce wear on the external Ptfe tube and allow the most smooth, least friction angle to go into the Ams buffer thus reducing the possibility of an error popping up)</a>&nbsp;<figure class="image image_resized" style="width:76.45%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393216/2024-01-10_6194006084695.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/53037" rel="nofollow noopener">- Ams Fix - Stack the Ams on tp (Using a carefully measured holder to hold the Ptfe in a curved angle that will allow filament to go through with the least possible amount of friction when the Ams is stacked on tp of the printer)</a>&nbsp;<figure class="image image_resized" style="width:77.35%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393216/2024-01-10_e6ff2df6c7873.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/58543" rel="nofollow noopener">- Ams Buffer Ptfe Right Guide Mount Fix will correct and maintain a nearly 100% straight line when the Ptfe tube exit the Ams buffer to move into the printer extruder.</a>&nbsp;<figure class="image image_resized" style="width:78.46%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393216/2024-01-10_f95cf24ce5c9e.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/85989" rel="nofollow noopener">- V2 Ams Buffer Right Ptfe Guide Mount - The Fix For Failed To Pull Back Filament a newly improved fix designed to replaced the V1 This will correct and maintain a nearly 100% straight line when the Ptfe tube exit the Ams buffer to move into the printer extruder. ez Installation. No screws needed!</a>&nbsp;<figure class="image image_resized" style="width:79.5%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393216/2024-01-10_6ddf689393292.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/63021" rel="nofollow noopener">- Extruder Ams Filament Pull Back Fix will correct and maintain a nearly 100% straight line to move the filament in and out of the extruder. This will also reducing wear on the Ptfe tube. Its design allow the filament to travel in the most smooth, least amount of friction and pressure for the proper angle to go into and exit the extruder thus greatly reducing the possibility of an Failed To Retract Filament error or similar errors from popping up.</a>&nbsp;<figure class="image image_resized" style="width:82.04%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393216/2024-01-10_4c9e59fa5529e.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/103987" rel="nofollow noopener">- V2 Extruder Ams Filament Pull Back Fix will correct and maintain a nearly 100% straight line to move the filament in and out of the extruder. This will also reducing wear on the Ptfe tube. Its design allow the filament to travel in the most smooth, least amount of friction and pressure for the proper angle to go into and exit the extruder thus greatly reducing the possibility of an Failed To Retract Filament error or similar errors from popping up.</a>&nbsp;<figure class="image image_resized" style="width:81.99%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393216/2024-01-10_69d2ccb8ac279.jpg"></figure>&nbsp;<a target="_blank" href="https://makerworld.com/en/models/67779" rel="nofollow noopener">- The Smooth 4 Way Splitter. Look No Further. Combined with Ams Hub Lite together with this small attachment, you will have the Smooth 4 Way Splitter.</a>&nbsp;<figure class="image image_resized" style="width:83.64%;"><img src="https://makerworld.bblmw.com/makerworld/draft/393216/2023-11-19_96f9eed020e9b.gif"></figure>&nbsp;<h2>Removal Video</h2><figure class="media"><div data-oembed-url="https://youtu.be/8sDRKjJCU2U"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/8sDRKjJCU2U" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure>&nbsp;<h2>Additional Notes</h2>The error itself is complicated and non definitive. Whatever cause the error today might not be the same area that cause the error again, same with person A and Person B setup, as the error itself is mainly due to tension with friction triggering the sensors in the machine.&nbsp;I would suggest you download and try and install all my fixes together for the proper effect as together they will ensure a smooth delivery of the filament with much lesser friction (read write ups) and hopefully that will help and reduce or resolve the error. If you use only one or 2 of the fixes the error could still happen as there are still other area might still be causing excessive friction.&nbsp;

AMS Filament Pull Back Fix V2 Updated

x1c upgrades

fay3dlab

Since my suspended millenium falcon was such a hit.. i was motivated to make more of them..This time i made the Suspended Imperial Star Destroyer.. the ship itself is modelled by nikoli2803 from thingerverse.. the circular frame is the imperial logo itself.. the whole frame i modelled it to look like the deathstar.. everything was done using Tinkercad.. The print comes in 5 parts..<ol><li>front ship</li><li>back ship</li><li>bottom clip</li><li>top left clip</li><li>top right clip</li></ol>The ship itself comes in 2 parts.. front and back.. and there are 3 clips to hold both side of the ship together.. the bottom clip will be the stand for the whole suspended star destroyer and the 2 clips works on any side..Its a bit tricky to assemble since you cant put both parts of the ship down since its suspended on the strings..<ul><li>so my suggestion is to put the bottom clip down on a table and then put the 2 parts into the clip..</li><li>it should fit snuggly together..</li><li>once the frame can stand on its own.. you can put the other 2 clips onto the frame..</li></ul>*UPDATE*I just made a new updated V2 of the suspended star destroyer.. with adding channel for LED light strips.. <img src="https://makerworld.bblmw.com/makerworld/draft/516824/2024-01-01_bdc509315a0c2.gif">you can download the new version here: <a target="_blank" href="https://makerworld.com/en/models/117449#profileId-126250" rel="nofollow noopener">https://makerworld.com/en/models/117449#profileId-126250</a>&nbsp;When printing suspended models.. one important thing to remember is to set the wall generator to arachne from classic.. this will make the slicer print the strings..I hope you guys have fun printing this suspended imperial star destroyer..

ams

Art

Art Projects

xmas

x1c upgrades

to do