3D Doodler

BUILD YOUR OWN FISHING BELT  the way you want it !!&nbsp;No support needed&nbsp;this is my design for a modular fishing belt you can tailor to your own needs&nbsp;The basis is the belt clip, available for 40mm and 50mm wide belts(i got mine from : <a target="_blank" href="https://nl.aliexpress.com/item/1005005029912906.html?spm=a2g0o.order_list.order_list_main.27.21ef79d2bVafMK&amp;gatewayAdapt=glo2nld" rel="nofollow noopener">ali </a>but any belt will do i think)&nbsp;Two different connectors can be used to attach accessories to the basis * The decagon connector which fits tight and can be fitted in multiple directions this prevents free turning, recommended for the rod holder as it has to stay in the position you set it initially * The round connector is ideal for accessories to freely move and is easier to remove from the basis clip,  recommended for the water bottle and the towel holderThe connectors attach to the accessories with a M3x8 screw (M3x10 also works for most parts) or you can use some glue.They can be extra secured with a 3mm screw in the side of the basis-clip&nbsp;accessories:basic set: * pliers holder * flat and angled rings (for carabiners etc) * rod holder&nbsp;extra accessories: * bottle holder * horizontal and vertical strap holder (for example Velcro straps to hold some gloves) * towel clamp alligator style, this one should be glued to the connector as there was no room for a screw * multifunctional hook * net holder (may or may not fit your net) * magnetic plate (needs 4 pieces of 15x2 neodium magnets * small bait box (needs 2 3mm screws to attach the lid)&nbsp;EXTRA EXTRA: Added a DIY plate which you can glue to anything you want or you can incorporate in your own design to make it compatible with the belt system.also added an extra decagon connector which is a little bit tighter to use when the normal connector would be too loose Print settings: Printed everything in PETG for strength and water resistance (don&#39;t mind the non-camouflage color as i used some petg i had laying around) standard generic petg settings 0.16 layer height 2 walls 15% infill no support needed ! (when having adhesion problems: CLEAN your plate !!  Post printing needs the yellow carabiners in the pictures are not included, you can find them here; <a target="_blank" href="https://makerworld.com/en/models/243919#profileId-260451" rel="nofollow noopener">Flexible Carabiner by Mc2_project3D - MakerWorld</a>&nbsp;Happy Fishing !!

Predator fishing tactical belt , modular system

Fishing

EPIQ3D

Give your plants/herbs the best start.This planterbox ensures that your seedlings stay fresh and hydrated.If you dont yourself grow plants/herbs, i know this will be a great gift for those who do.&nbsp;<figure class="image image_resized" style="width:86.29%;"><img src="https://makerworld.bblmw.com/makerworld/draft/854456/2024-04-12_9859755e4fc52.png"></figure>&nbsp;The Design is made to be as aesthetic as possible, to blend in no matter where you place it.There a two different bases, one for 8 planters and one for a single planter. Then you can choose if you want 4 or 5 in different locations.&nbsp;<h3>HOW IT WORKS</h3>This self watering planter is designed to slowly absorb water from the reservoir (This needs to be filled up occasionally).The lids provides a warm and humid environment for the seedlings, for this to work properly they should be printet in clear material.Individual lids ensures that you can remove lids from some of the seedsplants if needed, and others are not quite there yet.To prevent to much humidity and the risk of mouldy soil, the lids have ventilation holes.&nbsp;&nbsp;<figure class="image image_resized" style="width:86.29%;"><img src="https://makerworld.bblmw.com/makerworld/draft/854456/2024-04-12_16e56efe4909d.png"></figure>&nbsp;There are 2 water inlets in the planters, where it is recommended to use a wicking material at the bottom.This helps to absorb water into the soil slowly and prevent excess moisture in the soil. To much moisture can reduce oxygen in the soil, damage fine root hairs, and render the root system unable to absorb water.&nbsp;You can place a couple of cotton balls / cotton wool in the bottom of the pot.&nbsp;The planters are splittable to prevent damaging the delicate seed sprouts, when they are big enough to be transplanted.(When they are ready to be transplated, then check out my other self watering planters for herbs and flowers.)&nbsp;To prevent/slow down evaporation of the water in the reservoir (and stabilize the plantes), its recommended to use the provided lids.&nbsp;&nbsp;Optionally you can use the funnel to fill in soil to the planters, use the stamper to LIGHTLY press the soil down.Use the other side of the stamper (the poker) to make a hole for the seed. &nbsp;&nbsp;Basic print settings:<ul><li>Infill : 10%</li><li>Walls: 3</li><li>Top/bottom shell layers: 3</li><li>No support needed</li></ul>Dimensions: 8 planter base - H: 32.3, L: 231.8mm, W: 121.8mmsingle planter base - L/W: 66.8mmPlanter - H: 111mm, L/W: 42.8mm&nbsp;------------------------------------------------------------------------------------------------------------------------------------------If there is any issues or comments, dont hesitate to reach out.I will try to incorporate any issues to a updated design if needed.

Self watering Seed starter

garden

3Dimension Customs

Skeleton Middle Finger Keychain

alien

Ben Brandt

<h2>Steering Wheel Stand for Phone or Tablet: Park &amp; Watch</h2>Spending some time in your parked car? The steering wheel phone stand lets you quickly and easily set up your screen when you want to pass the time in your car. Simply unfold the stand and set up for easy “front and center” viewing for your phone or tablet on the steering wheel. The collapsible design folds up compact for easy storage, and opens up wide for a stable platform on the wheel. As long as the front of the steering wheel is sloped back just a little, the phone can lean back and sit stable against the flat surface created by the unfolded stand.<h3>Features:</h3><ul><li>Provides a flat surface to position your phone in front of you on the steering wheel.</li><li>Folds up easily so it can be stored in the door, cupholder, glove box, or center console.</li><li>The “hangers” and “feet” snap into place when collapsed, so they don&#39;t swing around when stowed away.</li><li>Scissor-like design allows the supporting pegs to be spread out wide for better stability.</li></ul><h3>Who is this for?</h3><ul><li>People who work on the road and need to take video calls</li><li>People who need to wait in their cars</li><li>People out on lunch breaks who want to catch up on some videos</li><li>Anyone who wants to pass the time while parked</li></ul><h3>Can this be used while driving?</h3>Certainly not. Using a screen while driving poses several safety risks. This is not to be used while driving; only when parked. Even if somebody tried, it would fall off as soon as the wheel was turned. This was intentionally designed NOT to clip onto the wheel, but only set on top and be held by gravity, thus it cannot stay in place if you&#39;re driving.<h3>Printing &amp; Assembly</h3><ul><li>Due to the high temperatures that can occur in a parked car, use a filament that can withstand high heat such as PETG, ABS, or ASA. PLA is known to warp in these temperatures and so is not recommended.</li><li>Assembly is entirely snap-together (see the assembly video in this post). This was done to make the model more accessible by not requiring people to get hardware. Also, the custom pins sit flush with the outer surfaces and don&#39;t protrude, thus keeping the design more compact and not interfering with the phone.</li><li>Parts are oriented in the print profile for ideal strength and appearance. If you&#39;re printing from the STLs, refer to the “3D preview” on this page to see how everything is oriented (this may be more obvious for experienced 3D printer users).</li></ul>

Steering Wheel Phone Stand: Park & Watch

Beerman

I originally printed the model I remixed this from but the threads would split so I added a nut and bolt instead.  M4 16mm bolt and two M4 nuts are required. &nbsp;It has a thread at the bottom that screws onto a standard tripod screw.  I didn't have any inserts but after testing the printed threads it's on there pretty good so inserts are not needed.

Phone Tripod Mount

phone

barbasnoo

This is a simple bin designed for the Honeycomb Wall Storage project. The bin is ideally sized to fit a small screwdriver set. In my particular use case, a Vastar 58 in 1 kit. I left a little wiggle room on all sides, but not too much. It could also be adapted/used to hold other things as well.

Honeycomb Wall Storage - Vastar Screwdriver Set Pocket/Holder

wall

music

Star Wars

e.axelsson

Basic organizer for ER32 collets with a neat lid to keep debris away. There are also versions available for ER16 and ER25.

ER32 Collet Storage

work

Mark Hähnel

This is a hook for the Ninebot G30 (D, E, II) with a hidden compartment for an AirTag.It is attached with the original screws that served to fix the handlebars.

Ninebot G30 AirTag Hook

scooter

PaulBB

<h4>Update 6th May 2023:</h4>Thanks for the great feedback everyone that downloaded and made this model! I finally had time to make a new version. I've added a few things to the model:<ul><li>A stopper that stops the drawer from beign pulled out completely. Designed in a way that you do not need any supports or extra prints.</li><li>Made the whole drawer about 2 perimeters thicker (0.8mm) (except the bottom). It is way sturdier that way. This was also needed to keep the stopper machanism working. Otherwise the whole drawer bent too much when pulling it all the way out.</li><li>Added an alternative version without the handle, but with just a hole to install your own (maybe 3D printed) handle yourself. The hole has a diameter of 4.2mm to install handles with a M4 screw.</li><li>Added a middle piece to join multiple drawers together</li><li>Added versions without the grid in the bottom.</li></ul>I am also currently working on some inserts which I will upload in a few days. &nbsp;<h2>Under Desk Drawer</h2>This model is designed to fit underneath your desk, providing easy access to your pens, papers, notebooks, and other essentials. Features a smooth sliding mechanism to ensure that your items stay secure and within reach. Plus, it's easy to install with the three mounting holes on each side. (I installed it with two on each side which works just fine.)The size of the bottom plane is approximately 166mm (width) x 176mm (depth) x 30mm (height).The slides are just mirrored versions of each other.Supports only needed for the drawer handle.Fits a 200mm x 200mm print bed.&nbsp;<h2>Installation</h2>This is the way that worked best for me, there may be better ways to install the drawer. Feel free to comment if you find a easier way :)<ul><li>Mount the slide that you plan to use as the outer-most first. Install one screw, align the slide perpenticular to the desk and install the second screw for the first slide. </li><li>Take the drawer and hold it a against the slide. Take the next slide and press it against the drawer where it should be. Install the back screw first and then the second one.</li><li>Repeat for each middle slide you plan to use. The middle slide has the same dimensions as a regular slide, so you can reuse the holes if you want to make it bigger later.</li></ul>Use two 3mm Screws per slide to mount the drawer to your desk. Be careful to not overtighten the screws as it may break the mounting holes depending on your material/print settings!

Under Desk Drawer

Desk

Stick Force

<h2>Compact print-in-place garden tool mount</h2>UPDATE: Now available as a parameterized OpenSCAD model that you can customize directly on MakerWorld!&nbsp;The mount is parametric and can be customized for exactly the size you need.&nbsp;I recommend using at least 3 wall loops and 25% gyroid infill for adequate strength and be careful when mounting the mount as too much screw force may split the layers.&nbsp;The model from OpenSCAD works with the tolerance set to 0.2 mm on my X1C when printing with Bambu PLA. The latch requires a bit of force to loosen at 0.2 mm tolerance and the hinge can use a bit of exercise before running a bit more easy. The tolerance set to 0.3 mm results in significantly smoother latch movements and easier first release. I would recommend 0.3 mm tolerance and the latch might still require a little wack with something to loosen.&nbsp;Other improvements on the new OpenSCAD model includes a strengthened hinge pin.<h2>Assorted sizes print profiles</h2><h3>Naming and file structure</h3>The files are structured with objects named as: &lt;toolWidth&gt;x&lt;toolDepth&gt;x&lt;height&gt;H-&lt;screwDiameter&gt;mm@&lt;tolerance&gt;mm&nbsp;And plates named according to screw diameter. Each plate contains the same tool width and 6 variations of tool depth.<h3>Printing on Bambu Handy</h3>When printing directly from the Bambu Handy app, please make sure that you only print the variant that you want.&nbsp;<ol><li>Select the plate by screw diameter. <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000025016/design/2024-06-13_af59b73884879.png"></li><li>Select the variant on the plate that you wish to print: <img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000025016/design/2024-06-13_6ef7c4290f128.png"></li></ol>&nbsp;

Garden Tool Mount

Garage

Trophy 

Nyxeka

Xbox One double wall mount bracket, designed to have no screws and use 3M strips to be rental friendly.

Dual xbox controller wall mount

Fun to do

xeebo00

Goonies Never say die light up sign<a target="_blank" href="https://www.buymeacoffee.com/xeebo3d" rel="nofollow noopener">Buy Me A Beer</a>

Goonies Sign Lightup

Signs

MEAF designs

Easy to print and fun to make!Perfect for your candy table, coffee table or any corner of your house&nbsp;&nbsp;Specially designed to fit in the buildplate of any mid size printer.The base is one piece. and every letter and details are separated files so you can print it in different colors even without an AMS.&nbsp;Designed two styles for every “O”. so you can choose what you like.<ul><li>First "O": choose between santa claus or tree ornament</li><li>Second “O”: choose between snowman face or snowman body</li><li>Third “O”: choose between reindeer or christmas elf</li></ul><figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/user/1795494732/draft/2023-09-02_n84evi4tipld.gif"></figure>&nbsp;split the "Details" file in to parts with your slicer and just print the details you like for each one and glue them on top!<figure class="image image_resized" style="width:50%;"><img src="https://makerworld.bblmw.com/makerworld/user/1795494732/draft/2023-09-02_o1xtzxx4tz4i.png"></figure>&nbsp;&nbsp;&nbsp;Print SettingsMaterial: PLA / PETGLayer height: 0,28 mm for letters and base. --- 0.2 for detailsNozzle diameter: 0,4mm or 0,6mmInfill: 10 -12%Perimeters: 2Supports: no&nbsp;Printing Tipthe tolerances are a little tight, so you will need some glue depending on your printer and/or filament calibration&nbsp;&nbsp;&nbsp;

Christmas hohoho Sign

Christmas

Smart3d by Gabriel Gomes

Nirvana logo  sign

Guitar

Whimsii3D

Sized to fit a Meijer TSA sized spray bottle. Will fit bottles with a 37mm diameter or less. I use it to keep a small amount of IPA nearby. Its a handy way to heep any of your small cylindical bottle organised on the HSW system.

HSW Isopropyl Spray Bottle Holder 

Hexagon Wall

That3DGuy

I created this model to stop this light switch from being flipped by my Niece's. It has been very useful in that sense

Light switch cover

Home Improvements 

OddPlasticity

As an owner of 3 cats, my shelf wouldn't be complete without a trio of ghost cats! If you enjoy these, it'd be lovely if you'd <a target="_blank" href="https://www.buymeacoffee.com/mlambertfrw" rel="nofollow noopener">grab me a coffee</a>. Want more? Here are some extra ghost cats:<ul><li><a target="_blank" href="https://makerworld.com/en/models/42133#profileId-42762" rel="nofollow noopener">Ghost cat licking leg</a></li><li><a target="_blank" href="https://makerworld.com/en/models/37949#profileId-36604" rel="nofollow noopener">Ghost cat stretching</a></li></ul>&nbsp;&nbsp;

Ghost Cat Trio

Halloween

RobDrivesCars

It's just a tray™ … or is it?Well, it is, but it's a small tray for small parts. Specifically, I designed these for screws when I'm working on fulfilling orders that require I sort specific length screws and count the quantity, but this could be useful for anyone doing any sort of small electronic disassembly!This is StackBox v2. It has several big upgrades over v1:<ul><li>No supports needed, ever.<ul><li>The bottom of the tray has flared. This allows for the ez-stack system do its job using simple bridging</li></ul></li><li>The spout has been redesigned<ul><li>It's now on an angle, meaning screws are less likely to spill out</li><li>The </li></ul></li></ul><figure class="image image_resized" style="width:63.34%;"><img src="https://makerworld.bblmw.com/makerworld/user/171771437/draft/2023-09-19_5lqjwej5c6id.gif"></figure>The base of the tray has a divided interior which allows you to sort two or more different types of items (like two sizes of screws) on either side. I also added ridges to catch small features like the lip of the screw head so it makes for easy sorting/counting.<figure class="image image_resized" style="width:39.77%;"><img src="https://makerworld.bblmw.com/makerworld/user/171771437/draft/2023-09-19_xrseczvlcuch.jpg"></figure>I also added a small funnel at the corner of the tray. This “spout” will just fit into a 2x3-inch (50x75mm-ish) bag in case you need to store those sorted items for whatever reason. There is a small lip right before the spout to prevent loose screws from just falling out of the spout.<figure class="image image_resized" style="width:39.3%;"><img src="https://makerworld.bblmw.com/makerworld/user/171771437/draft/2023-09-19_da87h1awsd5l.jpg"></figure>On, and did I mention they can stack? Because they can. It's kind of the whole point and it makes storing multiple kinds of screws or small parts for a single project super simple.There's also a small friction-fit lid in case you want to keep those parts free from the eyes of wandering cats.This print has been simplified to just three files:<ol><li>Small Tray: 10mm high walls</li><li>Medium Tray: 25mm high walls</li><li>Lid: It's a lid, kind of! There is no securing other than friction-fit (which depends on your printer tolerances). This is more to prevent bumps and spills.</li></ol>----The original v1 of this model (which is retired and will no longer be updated) <a href="https://www.printables.com/model/493058/" rel="nofollow">can be found here</a>.

Stackbox - The Stackable Small Parts Sorting Tray (v2)

Work

Boss Tech Print Innovations

Originally created by <a target="_blank" href="https://www.printables.com/@ColetonSessio_695492" rel="nofollow noopener">ColetonSessio_695492</a> and found on Printables, Link to the original model. <a target="_blank" href="https://www.printables.com/model/584344-skeleton-kit-card-tinkercad/files" rel="nofollow noopener">https://www.printables.com/model/584344-skeleton-kit-card-tinkercad/files</a>&nbsp;Perfect print for the spooky season. This skeleton kit card is quick print and can be easily be assembled in no time. PLA is a great choice, pick your favorite color PLA and print away!&nbsp;&nbsp;Print Settings:First layer height 0.2mmLayer height 0.16mmInfill Density 15%No support No brim&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;

Skeleton Kit Card

Kids

DesignCraft

DISCLAIMER: Print profiles NOT created by DesignCraft may contain outdated model versions or suboptimal slicer settings. Use at your own risk! I have no control to moderate or remove these third party print profiles.&nbsp;The Overture v2 print profile is the original print profile updated with a new model. It's a redesign based on user feedback and also uses about 40% less material. Please refer to the Disclaimer above and also please read the Considerations section below.&nbsp;Description:&nbsp;This adapter system wraps the edges of an OVERTURE 1kg 199x66mm cardboard spool in order to:<ul><li>provide smooth rotation within a Bambu Lab AMS</li><li>prevent carboard debris from depositing within a Bambu Lab AMS</li></ul>Features:<ul><li>Reusable</li><li>OVERTURE nameplate for easy identification when reusing</li></ul>Instructions:<ul><li>Print this model twice for a single spool</li><li>Affix one spool ring adapter on each side of the OVERTURE spool</li><li>See attached photos</li></ul>Considerations:<ul><li>Print Material: Please print with a basic PLA or PETG to minimize any shrinkage.</li><li>Too Tight? Too Loose? Cardboard expands with humidity and contracts when dried. A cardboard spool that has absorbed too much moisture may cause the adapters to fit very tight. Placing the spool in a filament dryer, such as the SUNLU S2, for a bit should resolve this. Note, you should not dry the spool with the adapters attached as they can warp in the heat. Keep in mind that after a long drying session the adapters may fit too loose. This should resolve itself shortly as the cardboard reabsorbs some moisture from the air.</li><li>AMS Lid Doesn't Close? All of the spool adapters I make are less than the official AMS spool clearance limit of 202mm, as specified on the official AMS product page, and as tested within my own AMS. However, some people have stated their spools are rubbing against the lid with the adapters attached. It's hard to say what's causing this since I cannot reproduce the issue myself, however, I've created an <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">AMS Lid Riser</a> which allows you to keep your AMS lid closed while providing additional clearance for larger filament spools. It's a quick and easy print which you can find on <a target="_blank" href="https://makerworld.com/en/u/243407759" rel="nofollow noopener">my profile</a> or directly here: <a target="_blank" href="https://makerworld.com/en/models/33133" rel="nofollow noopener">https://makerworld.com/en/models/33133</a></li></ul>