360aircraft

Valeria Momo

It's always nice to have a reference on hand!Print your own examples and material / color samples.

Material & color sample (swatches)

Refrence

sulleyneal

I always need a few of these in my truck for securing items!&nbsp;Two options for the end, either a hook or a loop. Works great with paracord and should work with thicker cord or rope as well.&nbsp;I recommend printing in PETG if you are going to keep it in your vehicle or use it in the sun. &nbsp;It has not been weight tested but seems very strong. I plan on using it to secure a hammock and yolo it.&nbsp;I CANNOT STRESS THIS ENOUGH, THIS IS NOT FOR CLIMBING!!!! USE AT YOUR OWN RISK.

Rope tensioners / Tie down Helpers

camping

SMatty

Hi, I would like to introduce you to my New Phone Stand Raised “Exagon”  Many of you asked me to create a new design of my model Phone Holder Exagon that could allow to connect the phone with charging. This design permits to connect the charging cable to the phone!  I hope you like it. Good Print !&nbsp;If you have any problems with adhesion you can try turning off aux fan when printing PLA&nbsp;You can find the first version here <a target="_blank" href="https://makerworld.com/en/models/193049#profileId-214820" rel="nofollow noopener">https://makerworld.com/en/models/193049#profileId-214820</a>&nbsp;You can find the rivisited version “V2” here<a target="_blank" href="https://makerworld.com/en/models/251302#profileId-267660" rel="nofollow noopener">https://makerworld.com/en/models/251302#profileId-267660</a>&nbsp;If you like my project consider supporting my job with a boost. Thank you !&nbsp;&nbsp;

Phone Holder Raised "Exagon" (allow charging)

Phone

SH Designs

This Easter Morning scene consists of 3 flat panels and a base which holds each panel slightly curved. No glue needed. Use an LED candle or fairy lights to light the scene for a dramatic effect. Each panel is setup to print face down on the bed to produce a nice texture.&nbsp;There are two base options: With spaces to hold LED tea lights, or without. UPDATE: I changed the bases to print facedown on the bed - they look much better with the texture on the top. The LED light version will have supports that are to be removed after printing.&nbsp;UPDATE #2: Added a smaller size to fit the A1mini or for those wanting a smaller scene.  Thank you to @moneyman89 for the suggestion&nbsp;If you like this model, check out the <a target="_blank" href="https://makerworld.com/en/models/64103#profileId-67178" rel="nofollow noopener">3 piece nativity set</a> next Christmas!

Easter Morning Scene

Easter

Filionix3D

Explore the fascinating world of spiders with Aracna, the card kit that brings nature into the palm of your hand. With a flexible and articulated structure, this spider moves realistically, inviting you to observe up close the wonder of arachnid biomechanics.Aracna is the perfect companion for nature explorers of all ages, with agile legs and a body rich in detail. Watch as it gracefully moves through your environment and display it with its web-shaped stand, adding a touch of elegance to your living space.The cards are designed to be printed in A1Mini size as well.&nbsp;Note: I added some extra pins so if you lose them you don't have to print again!!&nbsp;Note : The smaller size of the A1mini's spider web is due to the reduced dimensions of the printing plate. Since the spider took up too much space on the web, a smaller version was designed that cannot be placed vertically like the A1's, but can still be hung on the wall or left on a surface.<img src="https://makerworld.bblmw.com/makerworld/draft/671138/2024-03-06_28048ed93441c.png">&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/671138/2024-03-06_0979082105bbc.jpeg"><img src="https://makerworld.bblmw.com/makerworld/draft/671138/2024-03-06_9dd44edea8f37.jpeg"><img src="https://makerworld.bblmw.com/makerworld/draft/671138/2024-03-06_e2029f063a33c.jpeg"><img src="https://makerworld.bblmw.com/makerworld/draft/671138/2024-03-06_d94ac29bcf9c2.jpeg"><img src="https://makerworld.bblmw.com/makerworld/draft/671138/2024-03-06_fbf94606e6386.jpeg">

Arachna the Robot Spider Nature Explorer Card Kit

Halloween 

Whopper Printing

The truck has a working lever for picking up the trash can and dumping its contents, a working back door, and rolling wheels for added functionality. The trash can also features rolling wheels and a functional lid.For those with a small print bed, this can be printed by rotating the model 45 degrees. Ensure you have solid bed adhesion and that your printer can print with tolerances as small as 0.3mm. If you're unsure, try printing this. It has the same tolerances but it's a smaller model and a good test.&nbsp;NOTE: There are two versions, a standard version and a mini version. These are not just scaled versions of each other. They are specifically modified to share the same tolerances between the two versions. Be sure to choose the right pair of garbage truck and garbage can. Also know that the smaller model will have smaller joints and pieces which will make it weaker than the larger version. You could compensate by increasing your wall count if you print the mini version.&nbsp;UPDATE: I've added arm replacement files so you can print just the arms and cut/glue them however you need to.&nbsp;Get the kit card version here!&nbsp;If you would like to support me, consider these options:&nbsp;Social Links:<ul><li><a target="_blank" href="https://whopperprinting.com/" rel="nofollow noopener">WhopperPrinting.com</a></li><li><a target="_blank" href="https://patreon.com/whopperprinting" rel="nofollow noopener">Patreon</a></li><li><a target="_blank" href="https://whopperprinting.Etsy.com" rel="nofollow noopener">Etsy</a></li><li><a target="_blank" href="https://instagram.com/whopperprinting" rel="nofollow noopener">Instagram</a></li><li><a target="_blank" href="https://discord.gg/UfyQhUfn4N" rel="nofollow noopener">Discord</a></li><li><a target="_blank" href="https://www.tiktok.com/@whopperprinting" rel="nofollow noopener">TikTok</a></li></ul>

Functional Print-In-Place Garbage Truck

Toys

Printify

I designed a coat hook which holds up to 6 jackets and 1 or 2 hats. You just need 3 wood screws with a diameter of 4mm to attach it to a board or something similar.&nbsp;In the pictures I used PLA-CF because I had it lying around, but I am sure that Pla would be enough.

Coat Hook

House Projects

Stevengineer.ing

This socket rail set is for people who need several rows of sockets or to clip them together to make a much larger set as they can be clipped together. It holds 1/4, 3/8, 1/2 inch sockets.

Socket rail set

Tools

BamBam Design

<h4>Toroidal Windmill - Self adjusting turbine</h4>Looks like a spinning flower and no much wind is needed.<a target="_blank" href="https://youtube.com/shorts/WrKHW2Cdyvk?si=byQ_EpJAfOOy8x7F" rel="nofollow noopener">YouTube Short</a>&nbsp;<ul><li>Beautiful Windmill with toroidal Propeller Blades</li><li>Self adjusting to wind direction (Tail Blade Reworked)</li><li>100% printed, no Screws or tools needed</li><li>You can add 3 Propellers on one Axle with 2 distances</li><li>Full customizable with different propeller sizes and directions (I plan to add more cool propeller types as well)</li><li>Rods are stack able to your needed height</li></ul><h4>Printing:</h4>You can choose Propellers from 3 Print Profiles<ul><li>Basic Parts with Left&amp; Right Propeller to choose</li><li>Additional Propeller Blades</li><li>Additional Slower Propeller *New</li></ul>You can mix the propellers from these profiles.<ul><li>added one profile for A1mini without the biggest blade as well</li></ul>The rod could be a bit difficult to print, i added custom support, but clean your buildplate and apply some glue.&nbsp;PETG &amp; PLA tested👍🏼<h4>Assembly:</h4><h4>Info:</h4><ul><li>Added custom support to the horizontal printing rod</li><li>Added optional longer axle for more distance between propellers (10mm instead of 5mm).  With stronger wind the bigger blades should not collide.</li></ul>The Pitch from the Basic Blades:<ul><li>Big - Pitch 195mm</li><li>Med - Pitch 170mm</li><li>Small - Pitch 135mm</li></ul>Additional Propeller Blades with different numbers of Wings:<ul><li>Big - Pitch 190mm</li><li>Med - Pitch 160mm</li><li>Small - Pitch 130mm</li></ul>Additional “Slower” Propeller Blades:<ul><li>Big - Pitch 400mm</li><li>Med - Pitch 325mm</li><li>Small - Pitch 250mm</li></ul>Thanks to all followers and don&#39;t forget the virtual handshake 👍 ….Happy Printing&nbsp;Info II:My other windmills are fully compatible if you want to mix it up:<ul><li><a target="_blank" href="https://makerworld.com/models/235261" rel="nofollow noopener">Toroidal Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/250216" rel="nofollow noopener">Honeycomb Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/388124" rel="nofollow noopener">Elliptical Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/425419" rel="nofollow noopener">Sunflower Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/454861" rel="nofollow noopener">Raccoon Windmill</a></li><li><a target="_blank" href="https://makerworld.com/en/models/255324" rel="nofollow noopener">CLAMP for Windmills</a></li></ul>Info III:More modifications you find on my Patreon account.<figure class="image"><a href="https://www.patreon.com/posts/mod-608-bearing-105175595" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000235261/design/2024-05-30_3ad9786c3df1b.png"></a></figure>&nbsp;<figure class="image"><a href="https://www.patreon.com/posts/mod-pole-adapter-103628897" target="_blank" rel="nofollow noopener"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000235261/design/2024-05-30_70c92ad1f54a9.png"></a></figure>&nbsp;Commercial license you can get here:<a target="_blank" href="https://www.patreon.com/BamBamDesign/membership" rel="nofollow noopener">https://www.patreon.com/BamBamDesign/membership</a>

Toroidal Windmill - Customizable system

Ashley

squinn

Keep the contents of your 3-ring binder organized with this nice set of tabbed dividers. The tabs are large enough for labeling post-print, or 3D print text right on them in your slicer.&nbsp;The models are designed with a thickness of .6 mm, which creates a nice three-layered print at a layer height of .2 mm (and only consumes about 10 grams of filament). Three STLs are provided which can be used to create a full row of five tabs, top to bottom.

3-Ring Binder Dividers

office

planes01

<h3>Overview</h3>A-10 kit card&nbsp;Check out the <a target="_blank" href="https://makerworld.com/en/models/199176" rel="nofollow noopener">SR-71</a>, <a target="_blank" href="https://makerworld.com/en/models/242106" rel="nofollow noopener">B-52</a>, <a target="_blank" href="https://makerworld.com/en/models/436445" rel="nofollow noopener">A-10</a>, <a target="_blank" href="https://makerworld.com/en/models/402126" rel="nofollow noopener">787</a>, and <a target="_blank" href="https://makerworld.com/en/models/405459" rel="nofollow noopener">Darkstar</a>!Check out the full airplane kit card collection → <a target="_blank" href="https://makerworld.com/@planes01/collections/991821" rel="nofollow noopener">linked here</a>!<h3>Profiles</h3><ul><li>Kit Card<ul><li>plane in a kit card format ideal for gifting to others</li></ul></li><li>Model Pieces<ul><li>plane without a kit ideal for assembly right off the printer</li></ul></li></ul><h3>Filament</h3>As shown:<ul><li>Inland PLA Light Brown</li><li>Hatchbox PLA Cool Gray</li><li>Overture PLA Cement Gray</li><li>Overture PLA Space Gray</li></ul><h3>Tips</h3><ul><li>Model requires close tolerances to ensure snug but not tight or loose fit<ul><li>Make sure the model cools to room temperature before assembly</li><li>Ensure filament is properly calibrated with no excessive over extrusion</li></ul></li></ul><h3>Assembly</h3><ul><li>Remove all pieces from the kit</li><li>Debur as needed to smooth edges</li><li>Glue missile together (optional but recommended)</li><li>Let glue cure before proceeding to next step (optional but recommended)</li><li>Insert wing into forward fuselage slot</li><li>Insert engine pylon into middle fuselage slot</li><li>Insert horizontal tail into aft fuselage slot</li><li>Insert engine to pylon<ul><li>Recommend forward end first, then press down on the aft end. It will clip into place. (See gift below)</li></ul></li><li>Insert missile pylon to wing<ul><li>Recommend aft end first, then press down softly on forward end. It will clip into place. (See gift below)</li></ul></li><li>Insert vertical tail onto horizontal tail<ul><li>Recommend aft end first, then press down on the forward end. It will clip into place. (See gift below)</li></ul></li><li>Place airplane onto stand<ul><li>Recommend slot into the forward end first so that the tabs at the aft end do not accidently break</li></ul></li><li>Enjoy!</li></ul>&nbsp;<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000177353/design/2024-01-31_283fafe2d18ec.gif">

A10 Kit Card

Aircraft

J3DPS

Quick little sign for St. Patrick's Day.

Shamrock Love

St. Patricks

Deadpool1985

MPCNC"C" 23.5mm VersionReleased on 8/29/20Questions are best asked here, <a target="_blank" href="https://forum.v1engineering.com/" rel="nofollow noopener">https://forum.v1engineering.com/</a>Print Instructions<a target="_blank" href="https://docs.v1engineering.com/mpcnc/PParts/" rel="nofollow noopener">https://docs.v1engineering.com/mpcnc/PParts/</a><h4>Print Settings</h4><ul><li>Notes:</li></ul>Print Instructions<a target="_blank" href="https://docs.v1engineering.com/mpcnc/PParts/" rel="nofollow noopener">https://docs.v1engineering.com/mpcnc/PParts/</a>

Mostly Printed CNC Primo Version

Jack3D

Both AMS (flush lettering) and NON AMS (raised letters) versions provided.&nbsp;Print in whatever settings you fancy. Standard 0.2 settings are fine.

REMOVE BEFORE FLIGHT Label Keyring Keychain 

stuff

gare-sb

Guinness LED LightboxI made 2 versions. 1 time for an LED strip to be laid out with a USB connection, the second version with an on-off switch for 9V operation

Guinness LED Lightbox

Signs

Tomany

I decided to highlight my beloved AMS and I decided to create a frame with LEDs to honor it.I printed all the pieces in PLA and added a backlit label to the front.&nbsp;For those who have already printed and are using the AMS drawer organizer, know that the frame is compatible with it by making small changes which you will find explained in the attached PDF file&nbsp;If you want to make the writing even brighter, use a transparent material for it, opaque white is fine and allows light to pass through. For the lighting I used a 5V RGB LED strip and to adapt it to the frame I had to cut it into five pieces which I then connected with tin-soldered wires. I also thought about adding a cover to the LEDs to limit the intensity of the light and avoid any interference with the AMS optical sensors. You decide whether to apply it or not, I advise you to do so. To connect the four sectors of the frame I used butterfly keys, in the files at your disposal you will find two different sizes, I recommend you print the "KEY+0.10.stl" version which is 0.10mm wider and ensures a connection more rigid.&nbsp;<figure class="media"><div data-oembed-url="https://youtu.be/CweOJpjd5FA"><div style="position: relative; padding-bottom: 100%; height: 0; padding-bottom: 56.2493%;"><iframe src="https://www.youtube.com/embed/CweOJpjd5FA" style="position: absolute; width: 100%; height: 100%; top: 0; left: 0;" frameborder="0" allow="autoplay; encrypted-media" allowfullscreen=""></iframe></div></div></figure> As always, I hope you appreciate my work and I apologize for any grammatical errors, unfortunately I rely on Google Translate for the translation.