学习通打卡签到

BuildyBryce

A fidget toy designed to resemble the Bambu Lab AMS.&nbsp;Each filament spool ratchets and makes a satisfying sound when spun!&nbsp;<figure class="image image_resized" style="width:100%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000043249/design/2023-10-17_7116972d255e.gif"></figure><h2>Try Out My Other Fidget Toys!</h2><ul><li><a target="_blank" href="https://makerworld.com/en/models/61927#profileId-64376" rel="nofollow noopener">Filament Fidget</a></li><li><a target="_blank" href="https://makerworld.com/en/models/62596#profileId-65217" rel="nofollow noopener">AMS Keyring Fidget</a></li></ul><figure class="image"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000043249/design/2023-11-12_b34757f51518f.jpg"></figure><h2>Assembly Instructions</h2>Step 1: Cut a 60mm length of 1.75mm filament.<figure class="image image_resized" style="width:66.3%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000043249/design/2023-10-17_a548fc97a5865.jpg"></figure>&nbsp;Step 2: Attach the lid and base of the AMS together using the 60mm filament as a hinge.If the filament doesn&#39;t fit, ensure there is no support material in the hinge. If it still doesn&#39;t fit, adjust your print settings and try again (or use a drill/lighter).<figure class="image image_resized" style="width:66.02%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000043249/design/2023-10-17_4b2d515b33dea.jpg"></figure>&nbsp;Step 3: Assemble the 4 filament spools.The 2 halves should snap together firmly without glue.<figure class="image image_resized" style="width:66.11%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000043249/design/2023-10-17_6f3b91703aaf7.jpg"></figure>&nbsp;Step 4: Put the spools into the AMS and use the square bar to lock them into place.<figure class="image image_resized" style="width:66.05%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000043249/design/2023-10-17_056db6aadbe33.jpg"></figure>&nbsp;Step 5: You&#39;re done!If the filament spools don&#39;t rotate properly. Ensure that the ratchet piece is facing the correct direction, or flip the spools around.<figure class="image image_resized" style="width:66.11%;"><img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000043249/design/2023-10-17_4ca1d03ef553d.jpg"></figure>&nbsp;

AMS Fidget Toy

KobaRiley

<h2>Cable Tidy for Bambu X & P Series</h2>Got a bit tired of the messy setup on the back of the printer, and designed some cable supports that don't need screws or magnets.Also got a bit carried away and designed a few different versions.&nbsp;The PTFE tube on the right side, that goes to the printer, is free to move back and forth, but stays in the channel.The cables and tubes keep everything in place, but I've added some double sided tape on mine to keep it a bit tidier.<h3>Install</h3>To install the plate, you need to remove the two cables, and the left hand side PTFE tube. Then, remove the PTFE tube at the connector closest to the printer… feed that tube through the hole in the cable tidy plate, and then just reconnect everything.&nbsp;I've had this running on two printers for about 20 prints each, and have had no issues.&nbsp;There are different designs available, from 4, 3, 2 and 1 colour. The 1 colour basic version is by far the fastest to print… The Texas version is my favourite, and looks much better in reality than my awful photos….&nbsp;<img src="https://makerworld.bblmw.com/makerworld/draft/601192/2024-01-16_432ca9585a8cb.jpg">&nbsp;&nbsp;The cables and tubes can still be removed with the standard little tools that are everywhere on Makerworld, but I've included a couple that fit slightly better with with this plate.<figure class="image"><img src="https://makerworld.bblmw.com/makerworld/draft/601192/2024-01-16_6a6ab2a212209.png"></figure>&nbsp;This project took several days, and many many test prints. If you like the model, and feel like buying me a coffee, it would be greatly appreciated. <a target="_blank" href="https://ko-fi.com/kobariley" rel="nofollow noopener">https://ko-fi.com/kobariley</a>&nbsp;

看

用