BambuLab P1P Poop Chute
Copyright Claim
BambuLab P1P Poop Chute
Boost
10
14
10
Print Profile(1)
0.2mm layer, 2 walls, 15% infill
1.9 h
1 plate
Boost
10
14
10
0
46
105
Released
Description
A container for the BambuLab P1P, so that the remains directly on the back into this fall. Inside the container are two recesses for 22x2mm neodymium magnets, so that the container holds better and does not slip during vibrations.
CHECK MY OTHER DESIGNS:
- Shopping Cart Coin
- BambuLab P1P Poop Chute
- Bambulab Calibration Cube
- Lava Filaments Cardboard Spool Adapter for BambuLab AMS
- Shopping Cart Coin "Boobs"
- Shopping Cart Coin "Penis"
- Shopping Cart Coins for your Wallet or to give away by mail
- AMS READY - Screw measuring tool, M2-M10, 4-120mm
- The best simple Spool Holder
- Dick Shopping Cart
- Raspberry Pi 4B Desktop Case with UPS
- Smiley Shopping Cart Token
- Lockcard Wallet Einkaufswagen-Chip Inlay
- Helloween Shopping Cart Coin Ghost - AMS READY
- Helloween Shopping Cart Coin Scream - AMS READY
- Middle Finger Fuck You Helloween Ghost AMS READY
- The Grinch and The Grinch Keychain - AMS READY
- Santa Claus - AMS READY
- It´s cool Santa Claus - AMS READY
- The first Gnome at MakerWorld incl. Gnome Key Chain - AMS READY
- Silica Gel Can
- Merry Christmas Santa Claus - AMS READY
- The sexy Halloween Cartoon Vamp - AMS READY
- Autumn Halloween Christmas gnome
- Max from The Grinch - AMS READY
- Cindy lou who from the Grinch - AMS READY
- FC Bayern München Logo - AMS READY
- the cool dancing skeleton pirate - AMS READY
- Bart Simpson Skull - AMS READY
- Christmas Ghost - AMS READY
- BambuLab Make my Sign
- Headset Hanger - AMS READY
- Grinch Mode Stitch - AMS READY
- Jack Skellington Nightmare - AMS READY
- Boogiemann - AMS READY
- Lockcard Wallet Nintendo Switch Modul
Comment & Rating (10)
All
Print Profile
0.2mm layer, 2 walls, 15% infill
nice print. works as intended.
(Edited)
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Funktioniert super wenn nicht dauernd Fillament gewechselt wird, sonst dürfte es schnell überlaufen.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
on the small side but works as intended
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Worked well! thanks 😌
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-NoDerivatives
© 2024 MakerWorld