Fun little print if you have a doctor or nurse you want to show some love to.

Printed great. Works pretty well to rinse your smaller fruits. Drains are small, which is good for only letting water out, though it’s maybe a smidge too slow. Normal PLA is not food grade so if you’re going to use this as more than an occasional novelty you’ll probably want to seal it or find some food grade filament. (You mainly don’t want little crevices for food to get caught and grow bacteria.)

Printed this to replace the Bambu scraper. The angle of the blade on this scraper is much shallower and better for use on my coated Cryogrip plate. Works great. Note that the blade installs with the bevel and the screw heads on the bottom (you can only install it the correct way, but it will feel like you should hold the scraper upside down, which makes the angle way too steep).

Printed this just to try it out. Fits perfectly. Don’t think it’s really needed the way I have my cords secured, but why not.

Printed this on a lark, it comes in very handy when lubricating the X axis. Be careful not to squeeze too much onto the rail or it will drip down onto the plate below it. I have switched to using Singer sewing oil instead of the Bambu tubes, and this doodad still fits pretty well, though it does not screw on. Be aware that after you take it off, oil will slowly leak out of it over the next couple days.

Printed this on a lark, it comes in very handy when lubricating the Y axis. I have switched to using Singer sewing oil instead of the Bambu tubes, and this doodad still fits pretty well, though it does not screw on. Be aware that after you take it off, oil will slowly leak out of it over the next couple days.

Awesome print for Frosthaven owners. Packs the box perfectly. Note that tiles and books go into a separate file folder, or create some box lift on top of the pack. Be sure to read the attachment to see what goes where and how to pack it in layers. You may also want to plan out in advance which boxes you want to print in which colors. I accidentally started printing monster boxes in red and by the time I realized it it was too late to fix without reprinting a bunch. I did love the multicolor images on the sides of many boxes, adds a lot of panache. I did get a little bit of color bleed on my white and color prints, but I assume this was mostly my fault for not purging enough on color changes. You just might want to double check your settings to avoid having to reprint anything.

Basic, to the point, prints and works great. secures to the wiper assembly, you need to flex it to take it off. I didn’t realize I would need one at first, but sometimes the A1 will purge up higher than my poop bucket, even with its tall wall. Filament does occasionally stick to the deflector, but it is easy to knock off with a finger, and doesn’t hurt anything while it’s there.

I originally printed a basket connected to the wiper, but it was just way too small to deal with any longer multicolor print. This one is almost a perfect size if you don’t want something really huge, it can handle a 12 hour multicolor print. Only once did I find it just starting to overflow. Fits nicely around the gantry post. I think it’s compatible with the AMS top mount braces, but I don’t use one so can’t say for sure.

Fast, fun silk print. Very shiny and decent detail.

Fun gold silk print. Sides printed silky smooth. The printing on top was not as great for me. You might want to try Ariadne which I didn’t do and I don’t think came in as a default for me.

Easy print. Good for a basic small counter that doesn’t take up much space. I thought the counters stacked together somehow but they do not, they are all separate. The dials only spin one direction, so you can only count upwards, just something you need to know. The dial can also slip off the base, which you might find good or bad. The counters were VERY stiff after printing, hard on the fingers to spin. I waxed the base up a little which made it better, but only half the center piece is available to wax so it’s a little bit of a challenge.

My first silk print, looks great. Supports were a little hard to dig out in some places, but was an easy print for my first shiny piece.

Prints perfectly, clicks easily. Just a basic clicky fidget.

Prints great and nice looking multipurpose counters. Mine were VERY stiff and hard to turn at first, even with the knurled knobs and ridged dials. They do eventually break in but it was hard on the hands to try and get it there, with one direction almost impossible. Eventually I rubbed some wax around the threads and that immediately smoothed it out and made it much easier to spin and use.

Super fun artsy print. Very unique.

Printed and then didn’t use this for a long time. Then eventually bought some glow in the dark PLA which shouldn’t be fed through the AMS Lite, and had to finally set up my external spool. suddenly i am using this tool every day to swap PTFE tubes back and forth to my hub. Works great!

Worked perfectly. Early in my printing life I had some refills I needed to print from and no empty spools to put them on. these worked great. After a while though you are going to have more spools than you know what to do with and will start just throwing them away.

this thing is LOUD. As in hurt your ears loud.