planes01

<h3>Overview</h3>F-16 kit card&nbsp;Check out the <a target="_blank" href="https://makerworld.com/en/models/199176" rel="nofollow noopener">SR-71</a>, <a target="_blank" href="https://makerworld.com/en/models/242106" rel="nofollow noopener">B-52</a>, <a target="_blank" href="https://makerworld.com/en/models/436445" rel="nofollow noopener">A-10</a>, <a target="_blank" href="https://makerworld.com/en/models/402126" rel="nofollow noopener">787</a>, and <a target="_blank" href="https://makerworld.com/en/models/405459" rel="nofollow noopener">Darkstar</a>!Check out the full airplane kit card collection → <a target="_blank" href="https://makerworld.com/@planes01/collections/991821" rel="nofollow noopener">linked here</a>!&nbsp;<h3>Profiles</h3><ul><li>Small Model Kit Card<ul><li>Small plane in a kit card ideal for gifting to others</li></ul></li><li>Small Model Pieces<ul><li>Small plane without kit frame ideal for print &amp; build</li></ul></li><li>Large Model Pieces<ul><li>142% Scale to go BIG! Large plane without kit frame ideal for print &amp; build</li></ul></li><li>Small Model Kit Card (A1 Mini)<ul><li>Add mini support for kit format</li></ul></li></ul><h3>Filament</h3>As shown:<ul><li>Esun PLA+ Gray</li><li>Hatchbox Cool Gray</li></ul><h3>Tips</h3><ul><li>Model requires close tolerances to ensure snug but not tight or loose fit<ul><li>Make sure the model cools to room temperature before assembly</li><li>Ensure filament is properly calibrated with no excessive over extrusion</li></ul></li><li>Ensure good bed adhesion<ul><li>Make sure printer is fully calibrated</li><li>Make sure print bed is clean &amp; dry (soapy water is my favorite for cleaning - simple &amp; works)</li><li>Make sure filament is dry (wet filament can generate non-continuous flow that can cause bed adhesion issues)</li><li>Cooling &amp; Temps - make sure they are correct for your printer, build plate, and filament</li></ul></li></ul><h3>Assembly</h3><ul><li>Remove all pieces from the kit</li><li>Debur as needed to smooth edges</li><li>Glue tank together (optional but recommended)</li><li>Glue missile together (optional but recommended)</li><li>Let glue cure before proceeding to next step (optional but recommended)</li><li>Insert wing into forward fuselage slot</li><li>Insert tail into aft fuselage slot</li><li>Insert tank pylon to wing<ul><li>Recommend aft end first, then press down softly on forward end. It will clip into place. (See gif below)<img src="https://makerworld.bblmw.com/makerworld/model/DSM00000000160379/design/2024-01-31_283fafe2d18ec.gif"></li></ul></li><li>Insert missile pylon to wing<ul><li>Recommend aft end first, then press down softly on forward end. It will clip into place. (See gif above)</li></ul></li><li>Place airplane onto stand</li><li>Enjoy!</li></ul>&nbsp;<h3> </h3>

F16 Kit Card

Airplane Kit Card Collection

<h3>Overview</h3>print in place toy car&nbsp;<ul><li>No supports</li></ul>&nbsp;*Also check out the balloon powered version &gt; <a target="_blank" href="https://makerworld.com/en/models/117468" rel="nofollow noopener">LINK</a>&nbsp;<h3>Profiles</h3>R01 - Initial releaseR02 - Added ~1mm ground clearance. Also only paint outer layer of wheels&nbsp;

Airplane Kit Card Collection

Car Collection