Printed great with Bambu PETG HF Cream. No other changes to profile

Printed with Bambu Silk + purple. Came out great, easy

Printed easily / cleanly w/ Bambu PLA black. Unfortunately, did not fit my calipers (slot too narrow. This design slot is ~ 3.15mm. My caliper's prongs are ~ 3.5mm wide.) I considered sanding out the slot, but thought it may not be accurate enough & result in mis-measurements. I looked up "caliper hole center" & saw a picture that matched my calipers visually, downloaded to Bambu Studio & used the measurement tool to verify slot width (printing that one now). I like that THIS design (here) comes to a very sharp point (prints well), the new design I'm printing has a 2mm tip (1mm radius- probably fine, but maybe I will want to measure two <2mm holes on center?) When I first saw these designs online, I didn't understand them- I was thinking the other side of caliper jaws already measures single holes, BUT these designs measure center to center distance between TWO holes ("on center distance")-Maybe putting this phrase in this comment will help users find / understand them ...?

Printed easily with designers settings in Bambu PLA black. I didn't read all the instructions (like most people) and didn't realize Plate 1 has two handles (one open, one closed) and one perforation wheel. So I just printed as is and ended up with an un-needed handle without wheel. Then I just separated out the wheel from plate 1 printed it again and gave away the extra one. would be cool to separate out into two print plates each with a single handle and wheel (one with open handle design, and one with closed handle design).

Printed well in Bambu PLA Black. I did take the model into Tinker Cad to put a hole in the handle for hanging on a standard peg board hook ... (would be great and easy to add to this design for others ;)

Prints well. The Release could be easier to operate ;)

Awesome! There's lots of cool models, but this is maybe the first perfect perfect print I've made. Just open in Bamboo, click print, done, perfect, beautiful and useful! Printing THREE more (fit on P1 plate with some rotation and moving the purge tower) as gifts!!!

Came out nice in Bambu 95A HF

Came out very nice in black and white Bambu PLA

Came out nice in Red Bambu PETG HF (what I had available)

Came out nice in pink multi-color Bambu PLA. Also created a lid for it in Tinkercad

I edited for personal use and increased # of wall loops but otherwise used profile. PETG. Came out nice.

Printed with cream colored Bambu PETG HF, came out nice

Printed easy, came out nice- Note printed about 2" tall (instead of larger model size) out of Bambu PLA

Printed well. Haven't tried yet to attest to strength / usability

Came out great in PETG Red (the only red I had on spool, and I like these clips in red for visibility). The print came out great, no issues. Have used a couple so far and they seem to be working great, firm grip and sturdier than the prior clips I printed (which worked initially but seemed to lose their grip after a while)

Came out great. I printed 3 in PETG Red (the only red I had on a spool available). I did sand the top of one and heat it slightly to give it a finished look again.

Printed well, smoothly in Bambu PLA White. For some reason, it was too small (length & width) to fit business cards. especially with the posts inside the box frame at each corner. I have no idea what I did wrong, but assume it is probably my fault (I know sometimes the slicer carries forward some settings from prior prints, but I didn't think it carried forward scaling? And I haven't down scaled anything recently ). Just an FYI that others might want to do a double check of the measurements in Bambu-Slicer before sending to their printer. I REALLY LIKE that the height can be increased super easily / stylishly by simply copying the middle pieces and printing more of them. They will stack easily together to give you the ultimate box height you want. Thank you to designer!!

Printed well, smoothly in Bambu PLA Wood. I used Bambu Slicer to scale up the Z dimension so it could hold a taller stack of business cards. For some reason, probably my fault, it was a little too small (length-wise) to fit business cards well. It did bend and fit the stack of cards though, so it worked on first print. Thank you to designer!

Printed great in black and red (letters) Bambu PETG. I used Tinkercad to make more up to 80mm diameter radius and then used it immediately to design a model with perfect fit around the radius of the P1S printer (~54.5mm if I remember right). Thank you. If someone wants, and ok with designer, I can share the additional curve designs (Note I only made ones for OUTER curves, not inner, and made only 8 total tools to cover the radius sizes between the designers 30mm and the 80mm larges one in my set (so I did not proceed by 1 mm (or 50 would have been needed). I started by ~ 2's (eg 32, 35, 37, 40, and eventually by 5's 45, 50, 55 ... There are two OUTER curve sizes per tool)). In use, I estimated the fit on the P1S enclosure curve by what was between the two closest fitting tools and it worked GREAT!