Cool design. Needs a slightly larger hole to refill faster.

Great thought and design. Slightly smaller than model I have but works to its advantage as it’s a snug fit and won’t fall off. Printed with 7 walls and set patterns to concentric to shave off printing time and make it solid sturdy piece. Looks great although not sure if it actually works. Tried at low and turbo speeds and didn’t feel an increase in air volume or speed. Don’t have a way to test it.

Printed great! The magnet is a must since when the front flap is closed, it slightly bends upward or open a little. The magnet will keep it shut.

Very cool design! Kids loved it. Printed the base with supports for the overhang. Everything was printed in PLA except the support interface layer, which was printed in PETG. As you can see n the photo, it left the overhang completely smooth once the PETG interface layer was popped off (since PETG and PLA don’t adhere to one another). Going to try the nozzle with the 5 jets to see how that works.

Simple solution that was much needed. My daughter loves it and makes it easier to have cleaner water when she paints. She paints all the time. Everything is printed in PETG for water resistance. I added triangles to the tabs in the top tray to strengthen them, but it was a thought after the base was already printed. Will add triangle supports to the tabs in the base if I need to reprint it. My daughter wanted blue and white so I printed my own blue/white filament to use for the base and then sprinkled some of that filament through the print of the water tub to get the blue and white rings.

Very useful for the kids to keep the bottles out of the way and upright to dry instead of leaning against the faucet! Genius idea! Printed in PETG for water resistance.

Always wanted to get one of these. Now I can just print it! Brilliant! Despite what the designer says in the notes, supports are very much needed as you can see in the pictures. There’s an overhang that needs the support because it can’t print in mid air on nothing. This is the orientation the model loaded in. The mag clip is easy to break (printed in PLA) if you press down on it too hard, no need to press down don’t know why I did. The clip is strong enough to hold the mag engaged while loading but I found it easier to just hold the mag with one hand and push the rounds in with the other. Fits only 14 rounds with the plunger seated on the loader. 15 is doable but you’ll need to hold the plunger mid air before pressing the rounds in. Plain and simple it just works! Love it! Can fill my 50 mags quick now! Would love a 30 round version please!

Super simple way to empty your mag in a couple seconds! Beats doing it round by round! Genius. I increased the wall count to make it a solid piece. Lives in my range bag

Printed very well! Went together easy. The clamps printed in place with the base. They were well designed as I didn’t hear any noise or friction that was mentioned when operating the clamps. For being printed, the clamps have decent grip/force. Very impressed with the design. Don’t think the version with the metal springs is needed for soldering wires.

Very cool stand! Some minor under extrusion on the top, but that’s probably in part due to my filament settings. The car fit perfectly on the lego pins. Tight enough to not come out but loose enough to actually fit. About the the same tension as putting together 2 legos. Perfect! The labels are either embossed (raised) or flush with the surface.

Printed the next heavier force on the slide since petg was tripping it up. One for pos 2 and one for pos 3. So far so good.

Had to print the next step up heavier spring on the slide since the petg was causing it to slip and cut the filament too easily. So far so good.

These were great little stands for my sons Mini F1 cars. Printed very nice in PLA but the size of the lego pins were too small and the car barely attached to them. Had to scale it up and test print 4 times before I got the right size fit.

Printed well. The curve necessary to print it on the plate worked to its advantage, as it went down the drain easier. The fact that it’s taller and not as wide as others, made it flexible in all directions. This is a plus when dealing with bends and elbows in plumbing!

Printed quick and needed it in a pinch. Used this to straighten fins on a car radiator. Comb needles are surprisingly flexible and strong for PLA. Worked for my need.

Printed okay, lots of purge printing as is.

Printed great except might need to use 0.2mm nozzle to get better definition on the writing. Almost came out like chicken scratch on a 0.4mm.

Great idea but you need to get the tempo right or it’s just clicking noises

First test print with new P2S. Came out good

Had to cancel the first print. Needed brim then printed fine. Work good for the hextraction game but not heavy enough.