Search models, users, collections, and posts
Bio
I am the man with the trays
Achievements
Popular Creator
More than 1,000 followers.
Stellar Reviewer
Rate or Comment 313 different models
Pioneer Maker
Print successful 229 different models and 3,158 hours
MakerWorld Guardian
This badge has expired
Let the consolidation begin!
I am choosing to consolidate the sizing to a couple extra profiles per model listing, Due to the limit on the number of plates in a single file, I had to put all sizes <40mm diameter in one profile and list the sizes above 40mm into another profile. These were initially seperate models listings but since I am releasing Several more models I think this could help streamline your printing by grouping the models by socket length. Thanks again for all the support!
Universal Socket Tray - 112mm Length (3x grid)
255
955
Share
6
0
0
This model is for sockets 40mm or less in Diameter and less than 91mm in height. It uses the my new half-grid bottom which allows for use on standard Gridfinity bases while allowing placement options in 21x21mm increments. giving you 4 times the placement options as the standard bottom. I hope everyone enjoys this model as much as the other Makers who have changed the way they organize their tools with these sets
Thank you all for the boosts and support! 2500 prints reported and lots of fun!
Gridfinity Universal Socket Tray - 91mm (2.5 grid)
340
1.2 k
Share
3
0
0
FINALLY! You can fill in all your blank spots of varying sizes, This set includes the same half-grid base a my universal socket trays but is compatible in standard scenarios as well. This specific set of larger than 1x1 pieces will allow you to “realign” your blanks or tool trays as needed without the need for multiple smaller .5x1s and 1x1s. Instead you can just print a 1.5x1 or larger as needed up to a 3x3 grid cap.
Gridfinity Blank Cap - Filler - 1x1.5 to 3x3
119
376
Share
2
0
0
EXTENSION TRAYS ARE HERE - happy holidays my fellow OCD organizers. As always let me know if you find an issue with the model or instructions or need something custom that I am missing. I strive to make all my sets fully universal.
Gridfinity Universal Socket Trays - Extensions
867
3.1 k
Share
3
0
0
Unlabeled wrench trays for supporting the labeled trays with less number clutter in the drawers for a more clean look. Check it out! (or just keep on printing the labeled trays and label both ends)
Gridfinity Universal Wrench Tray (Unlabeled trays)
276
1 k
Share
4
1
1
Hello all OCD Makers!
Here is my 3/8" (inch) sized "Gridfinity Universal Ratchet Tray"
It has a custom snap fit label system and enhanced magnetic placement options with standard 6x2 magnets. No tools or glue needed, just click and print with satisfying snap assembly.
Also Cat approved just like the other ones!
Gridfinity Universal Ratchet Tray - 3/8 Inch
397
1.4 k
Share
1
0
0
Hello all OCD Makers!
Here is my 1/2" (inch) sized "Gridfinity Universal Ratchet Tray"
It has a custom snap fit label system and enhanced magnetic placement options with standard 6x2 magnets. No tools or glue needed, just click and print with satisfying snap assembly.
Also Cat approved just like the other ones!
Gridfinity Universal Ratchet Tray - 1/2 Inch
297
1.1 k
Share
0
0
0
Hello All OCD Makers, may I present the Gridfinity Universal Ratchet tray!
It has a custom snap fit label system and enhanced magnetic placement options with standard 6x2 magnets. No tools or glue needed, just click and print with satisfying snap assembly.
Cat approved!
Gridfinity Universal Ratchet Tray - 1/4 Inch
224
775
Share
5
0
0
No more data