Quick and easy to print, and it fits perfectly. I was roughly 30 minutes into gathering, cutting, and piecing together various models to create something like this for myself when I stumbled upon this model. It is 100% exactly what I was wanting. This model worked perfectly and was exactly what I needed. Thank you for sharing this model. I have donated a pair of boosts for your efforts.

This model was quick and easy to print, and it printed perfectly. It works exactly as expected and makes it easy to stash behind the monitor, making plenty of room on the desk. Thank you for sharing this model.

This AMS bracket is outstanding. Very simple print, and serves its purpose very well. Due to a separate issue, I had to relocate one of the AMS units which caused some troubles with the PTFE tubes & coupler to be in a bad spot. To solve my problem, I simply printed up some support rods to anchor into the brackets so I could run my tubes dead straight, solving my misalignment problems. It would be nice to see some sort of attachment brackets to clamp into those holes and provide options for accessories or other such items. Again, great model. Thank you for sharing.

Super simple, clean, and quick print. Printed bodies together on P1S and then print by object for all other parts on A1 so I could knock it all out on 2 plates at the same time. A tiny dot of super glue for each piece and my wife's honey-do order for 3x knitted teddy bears holding hearts has now been completed. Please consider making horrible models instead so my wife will stop asking me to print stuff. I mean, it's been 7-ish months since joining the 3d printer party people's possy, and I still haven't printed anything fun for myself. lol Thank you for sharing this excellent model.

Very simple, clean, and easy to print. A1, Bambu PLA Matte Scarlet Red with default settings other than print quality, which I bumped down (up?) from 0.16 high quality to 0.20 standard, which nearly cut the time in half for me while still retaining a great print. There were a few layer lines, though I had a filament issue which temporarily stopped the print causing each of the lines. The fault was all mine on those. As my wife had requested the bowl, my wife very much approved and appreciated the end result. I'm sure I will have a few more queued up soon enough. Thank you for sharing this model.

Feels pretty solid, no issues printing, Bambu PETG HF.It was a bit tight to initially attach, but that might be a good thing, as it holds nice and snug. Double boost from me, without hesitation. Thank you for sharing.

Super nice snake print. Quick, easy, and a very clean look and feel. Printed on P1S with default/included settings, which came out perfect. Used Bambu PLA Basic Gradient "Ocean to Meadow" for the body, and Bambu PLA Silk+ Gold and black for the eyes, as well as one set of eyes with the same gradient as the body. Thank you for sharing the excellent model.

Printed on P1S, quick and easy. Printed 4 bowls in 3 sizes, 100% (x2), 130%, and 140%. These bowls are super clean and look just like something you'd buy at a store.

Very nice print, easy, quick, and came out clean looking. Thank you for sharing!

Quick and easy print; P1S w/Bambu PETG HF, default/provided print profile, no issues. I printed the 3 & 8 mm (w/label) versions on a single plate to test if I would like it, which I do. Since these are useful and they printed great, I'll print the 10, 12, & 15 later on too. I pretty new to 3D printing and I only know 2 tricks. The first trick is making spaghetti on demand, and the second trick is adding a strip across the top X layers to add a 2-tone look. Since I've already eaten lunch, I figured I'd go with trick #2 for now, so I added a stripe to break up the white on white action. Thank you for sharing this great model.

Easy and clean print, had no issues. Printed everything in Bambu PETG HF, then went over text on sides of pens with acrylic markers to match colors. The embedded/press fit magnets areas were a bit tight on the 8-12 sizes. I used glue at first, to keep the magnets in their holes, but then my tiny brain finally booted up. It took me far too long to realize I could just use a small screw and a couple of nuts to effortlessly press the magnets into the holes. Maybe I should stop eating so many crayons... Additionally, I found it easier (remember, tiny brain here) to place the first magnet into the lever, then attach all the remaining same sized magnets to that one and mark the end of the last magnet so I know to connect it properly to the other end. All in all, a very nice print, and easy to use product. It would be nice to see an extension/spacer so all the magnets could be used. Thank you for sharing such a useful model! I very much appreciate you and your product.

Super nice print, and everything pretty much just fit together perfectly. I printed everything in PETG-HF with settings that were provided. Other than taking time to knock it out plate by plate, I don't think it could have gone any better. Thank you for sharing such a wonderful model.

Super easy print with no issues; Bambu PLA Silk+ (gold) & Hobby Lobby PLA Silk (Black/Pink), both set to default Bambu PLA Silk+ and printed at .08/High Quality settings. I was not in a rush so I loaded up 4 on aa plate and cooked them overnight. I was trying to get rid of the last little bit of a few different spools, so I set them all to matching colors/materials and let it go. I was hoping it would have swapped to a different spool before black/pink so I could get 3 colors without waste, but this came out nice anyway. Thank you for sharing.

Super nice print. My boy loves it. It is a bit thin, so I'd probably add a few mm thickness next time. Super cool, thanks for sharing.

Nice, easy, and clean print. Ended up printing both the black and white versions, and both came out perfectly fine. Thank you for the models.

Quick print, regular old PLA, and feels like it works well. The 2 pieces were a bit tough to jam together, but shaved a bit off and it snapped together.

My kid picked this model as our first 3D print. It was fast and came out great. He is very excited to have this as his new item to display on his shelf.

First time using PETG, so I figured I'd test it out on this. The print was quick and easy, nothing changed by me, and it feels like it might last/work just as well as some others. Thanks for the item.

I printed a batch with regular pla, as that's all I have at the moment. Everything appears to have come out perfectly fine and all the lids fit nice and snug.

printed 4 as a test with regular old pla. They printed quick and perfectly.