Spider-Man Faceshell - Free 3D Print Model

Search models, users, collections, and posts

Advotor

Props & Cosplays>Masks & Helmets

IP Report

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

Spider-Man Faceshell

Designer

15.6 h

7 plates

4.1(13)

Open in Bambu Studio

Boost

400

797

749

202

Released

Description

NOTICE: Credit is given to RooShoo and link to their project is https://www.thingiverse.com/thing:5266398

Print everything without supports EXCEPT the lens frames.

The face shell and lens includes holes for round circular magnets, of the following sizes.

4x of 6mm

4x of 8mm

Trim mesh into the lens clips as needed.

Sand down the face shell for comfort.

All sticking was done with Gorilla Glue, but can be done with any type of super glue.

There is a red mask over the shell. I will do the black web designs later with black fabric glue or hot glue.

I had a lot of trouble when printing because of the holes, so MAKE SURE ADHESION IS ON. This will save you a lot of filament, trust me.

If you are trying to save filament, don't print “spiderman_1_head_2_opt”. It is not extremely necessary, but would be nice and snug to have.

Good luck and ask questions!

Comment & Rating (35)

@user_624398915

What is the width of the magnets in millimeters

The designer has replied

Show original

@Advotor

The big ones are 8mm, and the small ones are 6mm.

@Advotor

You will need 4 of the 8mm, and 4 of the 6mm. And all this is only for the lenses.

@Advotor

The thickness of the magnets, however, don't really matter. It's good as long as it ranges from 2mm to 2.5mm.

@lojobloke

would the magnets be ok if I substitute the 6mm with a 5x2mm magnet? there would be a little of gap but theoretically

The designer has replied

@Advotor

mb for the late response but yeah definitely. As long as you have magnets that are in thickness of around 2mm to 2.5mm, it should be fine. Just make sure that ur glue is super duper strong so that the magnets don't fall out, since they are smaller. Iff you need me to i can put the link out for the magnets. They're just super cheap neodymium magnets.

@lojobloke

awesome, I made a model of a Spider-Man web shooter, would you tell me what you think of it

@user_1742170601

can u wear it?

The designer has replied

@Advotor

Oh yeah definitely. Look at the print profile pic. Although this model is designed for a smaller head, you may need to modify it if you want it bigger.

@user_1742170601

ok thanks

@Advotor

Replying to @user_1742170601 :

My pleasure!

@user_1893344432

ok so I printed it, can I get instructions on how to assemble it, thank you!

The designer has replied

@Advotor

Thank you for the comment. I completely forgot about that. If I get time this week, I'll make one, but for now, just try to look at the combined model on MakerWorld to try to piece it together.

@user_790179497

do you have to cut the white lense after printing?

The designer has replied

@Advotor

oh yeah just do it based on your convenience. However you want to stick it onto the black lense. I recommend measuring the white lens against the black lens, cutting it to a shorter length and then lightly soldering it to stick it on.

@user_1742170601

also do u have to use magnets or can u just hot glue it

The designer has replied

@Advotor

You need the magnets for the lenses, since the lenses need to go over the cloth mask, which is already over the the actual frame of the mask. So in simple words, everything that is not the lens, needs to be glued together. The lenses require magnets if you want a cosplay mask.

@user_1742170601

ok thanks

@user_268332601

Im waiting on my printer, but this will be the first thing i print!

@user_1354817705

Print Profile

Spider-Man Faceshell

Bed Adhesion Issue:it's not adhering to the plate, when it starts printing after 6, 7 minutes, it detaches from the plate

The profile uploader has replied

Show original

@Advotor

That sounds like a problem from your bed maintenance, fix that first before blaming the model.

(Edited)

@user_2478825129

Print Profile

Spider-Man Faceshell

Support Issue:it had floating parts

The profile uploader has replied

@Advotor

Could you please send a photo? All the floating parts of this print are printable without supports. I printed it three times on different printers as well.

(Edited)