FLASHFORGE ADVENTURER 5M ENCLOSURE - Free 3D Print Model

Search models, users, collections, and posts

Remixed by

Zdendys

3D Printer>3D Printer Accessories

IP Report

Print Profile(1)

All

H2D

H2C

H2D Pro

H2S

P2S

X2D

A2L

0.2mm layer, 2 walls, 15% infill

34.5 h

5 plates

Open in Bambu Studio

Boost

145

275

817

Released

Description

Remix of the model from the manufacturer. It uses parts from the original kit supplied by the manufacturer.

Differences from original for full functionality:
M3x6 mm bolt 3 pieces and M3 nut 5 pieces are needed. M3x30 mm bolt 2 pieces for hinge, or you can use original hinge with no bolts.

Attention!!! The original plexiglass needs to be cut from the bottom edge by 5mm!!! In the model, it is generally moved lower so that it does not hit the display, which is caught in the original brackets.

What is modified in the model compared to the original:

The top cover is thinner and lowered by 14mm.

The side covers are split.

The front plexiglass is lower by 5mm and therefore shortened from the bottom edge by 5mm.

It uses the original positioning of the display including its brackets.

The hinges use an M3x30 screw.

It uses the original coil holder.

I printed this complete under 800g of filament. Everything is printed from PETG. Supports are needed in a few places. Models A-D are printed flat on the bed.

Czech:

Remix modelu od výrobce. Využívá díly z původni kitu dodávaného výrobcem.

Rozdíly oproti originálu pro plnou funkčnost:
Je potřeba šroub M3x6 mm 3kusy a matice M3 5 kusů. Šroub M3 x 30 mm 2x pro panty. Nebo můžete použít původní panty bez šroubů.

Pozor!!! Původní plexisklo je potřeba ze spodní hrany o 5mm seříznout!!! V modelu je celkově posunuté níž aby nenaráželo o display, který je uchyven v původních držácích.

Co je v modelu upraveno oproti originálu:

Horní kryt je tenčí a snížený o 14mm.

Boční kryty jsou dělené.

Přední plexisklo je níže o 5mm a tím pádem i zkráceno ze spodní hrany o 5mm.

Využívá původní umístění displeje včetně jeho držáků.

Panty využívají šroub M3x30.

Využívá originální držák cívky.

Komplet jsem to vytiskl pod 800g filamentu. Vše je tištěno z PETG. Na pár místech jsou potřeba podpěry. Modely A-D se tisknou plocho na podložku.

Comment & Rating (5)

@tobi120388

Has anyone experienced whether this print works like this and do I need to lay the tilted parts or print with support? With the Orca Slicer, there is always an "out of range" message, although everything is on the plate

Show original

@OG_KungFuPanda

Is it out of range because of your Z limitation? I'd check there...your print bed may be large enough but the height in the slicer and/or the printer may not be...remember its 3 dimensions, X Y and Z. The slicer takes all of that into account.

@TommyT2008

could you please tell me where the parts go as Sam struggling

@TommyT2008

and do you print multiple parts twice

@OG_KungFuPanda

why won't this show up for the P1S printer? One can actually chop the larger pieces in half, put in joiners and print it still on a P1S...this is not the first time I've come across this with models too...why don't people allow the owners of their printer, print what they believe their printer could handle. It's like communism on here sometimes...frustrating and irritating how they take granular control of these little things.

No more