Super Mario Question Block Vault - Free 3D Print Model

Search models, users, collections, and posts

MILK+3D

Toys & Games>Puzzles

IP Report

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 2 walls, 10% infill

Designer

3.5 h

2 plates

4.9(19)

Open in Bambu Studio

Boost

256

614

605

258

Released

Bill of Materials

Bambu Filaments

Select all

PLA Basic

PLA Basic

Description

Boost Me (for free)

Boost me for free to support the creation of even more awesome models!

Behold, the Question Block Box - where your treasures are more secure than Princess Peach in another castle!

This sneaky little power-up comes with a secret drawer that would make even Bowser jealous. It's the perfect vault for hiding your 1-Ups, Star Coins, or that secret USB drive containing your totally legitimate backup of Super Mario Bros.

Just don't headbutt it expecting coins to pop out - we tried, and HR wasn't very understanding about the ceiling damage.

Warning: may cause sudden urges to make coin-collecting sounds while opening. Not responsible for any mushroom-related growth spurts or random appearances of Goombas. Keep away from plumbers in red hats.

Explore the Collection — Star Wars Busts

👉 See the full Star Wars Collectibles collection →

🛠️ Browse all my designs on MakerWorld →

If a MILK+3D design earned a spot on your desk or shelf every coffee fuels the next release.

Comment & Rating (51)

@user_3722302311

Print Profile

0.2mm layer, 2 walls, 10% infill

haven printed question marks yet but happy with it as is

The profile uploader has replied

@jpleite

wow! it tuned out really good in gold! thank you for sharing

@Matchagirl97

Print Profile

0.2mm layer, 2 walls, 10% infill

perfect only defect it does not close well if the banknote box is put inside

The profile uploader has replied

Show original

@jpleite

you mean when the hidden box is the box does not close properly? what filament did you use so I can try to understand the issue

@user_2360503592

Print Profile

0.2mm layer, 2 walls, 10% infill

amazing model 👍

The profile uploader has replied

Show original

@jpleite

Thanks for you comment, photos and rating!

@3dane

Print Profile

0.2mm layer, 2 walls, 10% infill

Great model, but the pin is a bit too loose.

The profile uploader has replied

@jpleite

thanks for your feedback and rating. may I ask what filament and brand did you use so I can try to replicate?

@3dane

Replying to @jpleite :

Bambu Basic PLA 10402 on an H2D. I think it might have to do with the pin not being the exact size as the hole. I glued it now to secure it.

@jpleite

Replying to @3dane :

thanks for the feedback. will test and improve it

@pya_3d

Boosted

It printed beautifully! I only wish I could print the box in a single piece. I'm not referring to the lid, but the cube itself, without the drawer. Another improvement I would make is the hinge pin, which is loose and slides if you don't add glue. With these improvements, I would undoubtedly promote it, as it is a superb model. Thank you for sharing!

Show original

@brits

Print Profile

0.2mm layer, 2 walls, 10% infill

printed for a boy who loves mario and trinkets. gorgeous

The profile uploader has replied

@jpleite

thank you so much for the rating and comment

@e.warren.d

great model, thanks! quick question to make sure I’m not smoking fajitas…are there supposed to be 4 extra screws?

The designer has replied

@jpleite

yes. I have to correct the file as I duplicated more than I should have. so 4 of them are not needed. sorry for that

@e.warren.d

Replying to @jpleite :

NO APOLOGY NEEDED!!! I'd think about keeping them, you never know when you may need one! Thanks again!

@user_4108746224

The pin that closes the box is too thin and doesn't stay in place. When I fit the drawer, I can't close the cube, it's necessary to reduce it by 0.5mm perhaps to fit perfectly I printed it on the Bambu Lab A1 with stlflix filament

The designer has replied

Show original

@jpleite

tolerances are hard to get right for all filaments the enclosure was designed and tested with bambu filaments and it fits well i also tested with Sunlu successfully i don't know this brand but it might have other tolerances thanks for the feedback

Show original

@user_2282546315

Print Profile

0.2mm layer, 2 walls, 10% infill

Top

The profile uploader has replied

@jpleite

thank you

@flaoki

Print Profile

0.2mm layer, 2 walls, 10% infill

The piece is very beautiful. We love it for storing money and change

The profile uploader has replied

Show original

@jpleite

obrigado!

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Super Star [SUPER MARIO]

Joker 3D

6.4 k

2 k

super mario painting (HueForge)

Teixi3D

5.7 k

2.2 k

Super Mario Coin

LCoolo

6.2 k

1.7 k

Super Mario Piggy Bank

Break the Bank

6.5 k

3.1 k