The Thwack - REMIX by JabbaTheHutt - Free 3D Print Model

Search models, users, collections, and posts

Remixed by

JabbaTheHutt

Tools>Hand Tools

IP Report

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm nozzle, 0.2mm layer, 4 walls, 75% infill

Designer

12.7 h

1 plate

4.8(28)

0.2mm layer, 2 walls, 75% infill

Designer

5.9 h

1 plate

4.8(5)

Open in Bambu Studio

Boost

196

319

172

Released

Description

THE THWACK

Here it is! A big thank you to Mr. MegaTronic for this awesomme hammer.

I tuned it for a Bambu printer, and made a hole in the handle for lesser filament use, but at no cost to the functionality of the hammer.
Surprisingly sturdy and can use to hammer down those 3d prints. I use it for magnet insert, nuts, bearings and plastic vs. plastic ;-)

And the best thing, full speed ahead on the X1C - printet in sportsmode.

Comment & Rating (49)

@jewzaam

Boosted

Print Profile

0.2mm nozzle, 0.2mm layer, 4 walls, 75% infill

Strength Issue:It printed well but the layer line orientation means with a strong blow of the hammer the hammer head may pop off. It did pop off in my case.

The profile uploader has replied

@JabbaTheHutt

Did you do it with 75% infill or more? And try to print it while it flat on the bed.

@JabbaTheHutt

https://youtube.com/shorts/_ZoAhh6MTHU?feature=share

@jewzaam

Boosted

Replying to @JabbaTheHutt :

Yes 75% infill. I have not tried flat, which would be a different profile. The upright profile is what I am rating, it results in a weak hammer.

@AstraCD

Print Profile

0.2mm nozzle, 0.2mm layer, 4 walls, 75% infill

Nice design

The profile uploader has replied

@JabbaTheHutt

love your choice of colour 👍🏻

(Edited)

@user_194636472

Print Profile

0.2mm nozzle, 0.2mm layer, 4 walls, 75% infill

Very handy, came out looking pretty snazzy in BL PLA tough Yellow

@tocpap

Print Profile

0.2mm nozzle, 0.2mm layer, 4 walls, 75% infill

Excellent design, perfect for putting printed parts together. Printed using the provided profile. Thanks for sharing!

@WallaW80

Print Profile

0.2mm nozzle, 0.2mm layer, 4 walls, 75% infill

A1 Mini printed as programmed, everything went well

Show original

@user_592633703

Boosted

Print Profile

0.2mm nozzle, 0.2mm layer, 4 walls, 75% infill

wow this is seriously hard solid and just pla basic I could use it as a weapon if needed ! I’m using it for display purposes but super happy with it and I might print another for a craft hammer

(Edited)

@user_915925824

Print Profile

0.2mm layer, 2 walls, 75% infill

good looking hammer but I couldn’t get the supports off clean.

The profile uploader has replied

@JabbaTheHutt

what material did you use? was the support set to 0.1 or can u use a support material.

@user_915925824

I used PLA+ for the hammer and supports. I didn’t change any settings and that might of bin my fault if it didn’t turn out good. If you have any advice on supports I will try and print again and change my review.

@blake3dcake

Works better than expected! https://youtube.com/shorts/_ZoAhh6MTHU?feature=share

The designer has replied

@JabbaTheHutt

Wow never tried to hit nails with it. Ill try that too, got plenty of theese hammers printet by now :D

@banjo_horse

Print Profile

0.2mm nozzle, 0.2mm layer, 4 walls, 75% infill

My sons love this, printed easily as well. I layed it on the side ( for better layer strenght ), and peinted it out of PLA with PETG as a support interface.

The profile uploader has replied

@JabbaTheHutt

Im glad you and your sons loved it. I love it too. I have printet a lot of this, bot on the side and stand up, Both have great strenght. But youre right, its a bit better if it on the side :-)