Auggie19

cover

IMG_3485.JPG

plate_1.png

plate_2.png

2024-12-09_3e800e49bfc2a.jpg

IMG_3486.JPG

.20mm StrengthTree Support Default&nbsp;Used Bambu Lab PETG HFGyroid infill 25%, for 5/8" bolt infill 100%

0.2mm layer, 6 walls, 25% infill

plate_3.png

plate_4.png

AMS Lite Pivot Wall Mount.JPG

AMS Lite Pivot Wall Mount 2.JPG

AMS Lite Pivot Wall Mount 3.JPG

This is a print profile for the A1 mini. Although I could combine parts together, I decided to separate the larger pieces and place them separately on their own plate. There are 4 plates total. &nbsp;Same settings as the original profile for the A1 - .20mm Strength profile with tree supports for critical regions only. &nbsp;Please remember to ensure that your A1 or A1 mini&#39;s build plate(s) are clean especially if you are printing different filaments. I had adhesion issues trying to print PLA after I just printed PETG.  There could have been some PETG residue that caused the adhesion issues. Clean the build plate with dish soap and water and dry with a microfiber cloth. &nbsp;Also, make sure that your table where your printer resides is stable and does not add any further stability or vibration issues. Good luck!&nbsp;

A1 Mini 0.2mm layer, 6 walls, 25% infill

IMG_3757.JPG

IMG_3756.JPG

The original pivot attachment was fine but there were certain areas that looked rough because I didn&#39;t use support. I filled out the cut outs and made this attachment solid. It does use more filament but I prefer the solid and smooth look. &nbsp;I used Bambu Lab PETG HF in Dark Gray and used the Strength profile. Please use the other other print profiles for the other parts.&nbsp;Please remember to ensure that your A1 or A1 mini&#39;s build plate(s) are clean especially if you are printing different filaments. I had adhesion issues trying to print PLA after I just printed PETG.  There could have been some PETG residue that caused the adhesion issues. Clean the build plate with dish soap and water and dry with a microfiber cloth.&nbsp;Also, make sure that the table where your printer resides is stable and does not add any further stability or vibration issues. Happy Printing!

Solid Pivot Attachment - 0.2mm layer, 6 walls, 25% infill

Minbil1

Skærmbillede 2025-12-09 210923.png

Skærmbillede 2025-12-09 210910.png

Slightly Smaller Nut, Bolt and Washer0.2mm layer, 6 walls, 25% infill

Slightly Smaller Bolt Nut and Washer

user_3356148011

IMG_5537.jpeg

Added a small clip for the backside to hold the AMS lite cable in place. I just glued it in place.

0.6mm nozzle, 0.3mm layer, 2 walls, 15% infill

user_3383338586

ams lite pivoting wall mount

<boostme><boosttitle>Boost Me</boosttitle><boostcontent>Please consider a like or a boost token for me to show support - I would greatly appreciate it!</boostcontent></boostme>I wanted to wall mount my AMS Lite and really liked the idea of a pivoting mount so it would be easier to replace filament spools.<a target="_blank" rel="noopener noreferrer ugc" href="https://makerworld.com/en/@egil.opsahl">@egil.opsahl</a> did a great job of modifying some of the parts using Fusion 360. He was nice enough to provide me with the .f3d file (Thanks again!) and I decided to modify it further:<ul><li>I wanted to use the original 5/8&#34; bolt so I changed the holes back to accommodate.</li><li>I found a printable 5/8&#34; bolt, washer, &amp; nut using Easy Bolt (https://www.thingiverse.com/thing:6308320). Thank you to jbruce12000.</li><li>Strengthened the pivot component further and removed from overhangs so there were less support needed.</li><li>Changed the screw holes on the wall mount plate from 4 to 2. I wanted to ensure that the 2 would hit the stud on my wall. I used 3&#34; construction screws to mount the plate.</li></ul>The print profile uses the .20mm Strength profile with Gyroid infill. The 5/8&#34; bolt I used 100% infill just to be sure it was stronger - perhaps overkill? This is my first ever post/remix and have really enjoyed my A1 so far. Thank you,

AMS Lite Pivot Wall Mount

ASIA

Print Profile(5)

Description

Comment & Rating (585)

This remix is based on

License

Related Models