Shots dispenser & carrier for parties (spill free) - Free 3D Print Model

Search models, users, collections, and posts

Team Guapos

Household>Festivities

IP Report

GIF

Print Profile(1)

All

X1 Carbon

P1S

P1P

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.28mm layer, 2 walls, 15% infill

Designer

4.9 h

2 plates

4.6(16)

Open in Bambu Studio

Boost

111

303

289

158

Released

Description

A shot dispenser for parties and get togethers.

With this dispenser you can to distribute your shots evenly.

Using this prevents you from the mess that normally happens everytime you pour shots, serve or transport them... Especially with drunk people…

Say goodbye to unnecessary messes that you have to clean up afterwards. :)

Just some remarks for food safety and 3D-printed Materials.

As you know, 3D-printed materials are NOT food safe in the long term. Due to the gaps between the layers and the pores, there can be residues left behind even after cleaning. Therefore i would recommend to not use it daily and not too often. Make sure you dry it between uses properly. Also stronger and clear alcohols (>30%) should be better and more safe to use in the long term.

This print is more like a party gag for occasional use.

I used the following shot glasses: ⌀34,5 mm at the bottom,⌀45,5 mm at the top.

https://www.amazon.de/Schnapsgl%C3%A4ser-Glas-Set-Shotgl%C3%A4ser-Sp%C3%BChlmaschinenfest/dp/B06XXFGHPP/ref=sr_1_5?keywords=shot%2Bglasses&qid=1701785489&sr=8-5&th=1

My print was:

0,28mm for the bottom part
0,2mm for the top part due to the threads
0,2mm for the nozzles (0,28 possible)
I adjusted the M10 thread a bit for a smooth fit and to take into accounts the tolerances of 3D printers

Added the Fusion 360 File for you to make your own models and to adjust it for your needs.

Have fun :)

Comment & Rating (18)

@user_4093557571

I make a batch of formula for my son every night and divide it into 6 bottles. Do you think these bottles would fit/ stand flat? The bottle opening is 39mm and at the widest is 64mm

The designer has replied

@TeamGuapos

please please don't use this model or ANY 3d printed stuff in combination with food, even less with a baby!! you can be sure that mold, bacteria and other stuff will be between the layers and you won't be able to clean in properly. so no, don't use this for a baby and read about that topic...

@toppsikrett

Print Profile

0.28mm layer, 2 walls, 15% infill

Thank you

@danibu37

Print Profile

0.28mm layer, 2 walls, 15% infill

Finished result very polished but at the very beginning of the base piece I did have some issues where there was a wider headspace over the previous layer so the next layer got lumpy because it didn’t have close contact to adhere, but I let it keep going and it fixed itself. all of the pieces connect together nicely, and the nozzles are water tight. I used a small wrench to put them on tight but don’t over do it or anything. It doesn’t fill each glass with the same amount of liquid but it does well at putting some in each, and taking off the top part to transport the cups makes for a steadier handoff and looks cool too. I was messing around testing it out for spilling and I was surprised how well the cups stayed in and no liquid came out so long as you have a loose wrist about it and let it kind of swing as you move. I made one for new years and my mom loves it so I made one for superbowl for her. Hope I can upload pics later because I don’t have any yet and have already boxed it up but this is a cool gift for people who party with adult beverages 👏