Philips Norelco Oneblade protective Case - Free 3D Print Model

Search models, users, collections, and posts

Oddball Design

Household>Other House Models

IP Report

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.12mm layer, 2 walls, 15% infill

Designer

4.2 h

1 plate

4.4(18)

0.2mm layer, 2 walls, 15% infill

Designer

1.8 h

1 plate

3.9(24)

Open in Bambu Studio

Boost

250

755

793

497

Released

Description

Boost Me (for free)

My models are free of charge. Please boost me to enable me to make more free models for Makerworld or to buy me a coffee

A rectangular model of a protective case for the Philips Norelco Oneblade

Nice present for someone or for yourself a handy case for your Oneblade.

It fits perfectly. Lots have printed it out succesfully. Please rate the model and add a picture of your case.

Easy to print (PETG/PLA)

Recommendation when it closes tight:

It closes tight and perfectly.

If it closes too tight, just sand or file the 2 small semicilindrical notches a little and it will close very easy.

Please boost the model and, if you like, leave a picture of your printed case below in a comment.

Success! Happy printing.

Comment & Rating (54)

@wrednababazzusu

Print Profile

0.2mm layer, 2 walls, 15% infill

Printed in PETG and broke immediately.

The profile uploader has replied

@Pirulero68

I'm sorry to hear that. Have you dried your filament and used the right speed and temperature?

@mrtkn

I've had the same issue. I think the design needs some improvement. More visual differentiation to identify what direction does the cap need to go. Some lips on the side to be able to grab it easily when opening it. And a stronger tab design.

(Edited)

@yaoi

Print Profile

0.2mm layer, 2 walls, 15% infill

nice and quick print.finished right in time for my flight, usually the blade breaks during those. feels incredibly solid, built like a tank. opening it could be a little easier but I don't mind too much since I won't use it all that often. pro tip is to not remove it from the plate until it has cooled tho, I didn't wait and the lid warped a little. s

The profile uploader has replied

@Pirulero68

Hi, thanks for your comment and have a good flight. It closes firmly, but a little sanding on the 2 "lips" will make it a lot easier

@Robus_33

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

good

The profile uploader has replied

Show original

@Pirulero68

Thanks. Did you encounter any problem that I don't know of?

@jclarkusaf

Print Profile

0.2mm layer, 2 walls, 15% infill

perfect fit, the tabs are a little brittle with PLA

@Pykast

Print Profile

0.12mm layer, 2 walls, 15% infill

Assembly presents minor challenges, otherwise the device fits perfectly and is quite robust

Show original

@Quaihn

Print Profile

0.2mm layer, 2 walls, 15% infill

Nice design and nice to have on my trips, so i dont accidentaly start it all the times.

@tugboat5438

Print Profile

0.2mm layer, 2 walls, 15% infill

good design, could be better if there were tabs added for easier opening

@Austin94

Print Profile

0.12mm layer, 2 walls, 15% infill

this struggled to print on my P1S but printed fine on my X1C. I tried 2 x on the P1S and both times it failed once it started to print the sides up. I then broke the one that worked when I tried to close it. the tolerance was very tight. but even with one of the tabs broken off, it still shuts and with a rubber band I’ll make it work. 😀　Thanks for the file.

The profile uploader has replied

@Pirulero68

Hi, I can only test it on my X1C. No issue at all with tolerances, but I consider to make a version where the tabs ale more loose, will that work?

@Austin94

I think that would work.

@WWWWWWWMWMWWWMW

Print Profile

0.12mm layer, 2 walls, 15% infill

Fits perfectly, it is a very secure snap to secure the lid to the container... Almost requiring a coin or something small for leverage, but I don't see this as a detriment as I'd rather not have it opening up after being shuffled in a bag.

@halexaron

Print Profile

0.2mm layer, 2 walls, 15% infill

great for traveling

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.