If you want to mount your AMS on the wall and still have easy access to it, try the angled bracket.
Due to the 2 bars in the model, it currently fits all AMS versions. Whether 3 chambers with different dimensions or the newer design with 5 chambers.
Due to the adapted width of the holder, the original feet of the AMS stand up perfectly.
The cable and the PTFE tube can simply be fed down through the holder.
The lid stays open on its own without having to be fixed.
The distance between the holes is 318 mm.
If you need a longer AMS cable, you can buy it HERE or in the Bambulab Store.
Changelog:
Update 16.06.2026:
Just a quick “external” upload today for improved cable management:
Fits perfectly for PTFE tube, AMS cables, and all other cables up to 5 mm in diameter.
Update 18.03.2026:
It only takes half the time and half the filament!
Today, another major update and improvement to the "Extension AMS wall mounting," now in version 2 😉 It took a long time, but I was finally able to implement it and test it successfully. Many comments and PMs about increased filament consumption prompted me to create an improved version.
Another advantage is that there is now only a one-piece version, which can also be printed on the P&X series!
Due to its size, perfect bed adhesion is essential! The very wide brim should help with this. We also recommend BIQU’s CryoGrip 😉
In the center of the new Version 2, there’s an additional connector/option for more accessories. Please let me know if you come up with any great ideas for it 😊
Of course, the old coupling remains unchanged, and you can still use your accessories!
And finally, one more improvement - you don’t have to remove the wall mounts to install or remove the unit. You simply slide it in sideways or tilt it to fit between the mounts 👌
Feel free to leave me feedback, ideas, or suggestions for improvement 😉
Update 09.02.2026:
Roll holder insert for AMS wall mount
Left and right versions included in the profile
Perfect fit - no gluing or other fastening required. Simply clip in the roll holder and you're done.
Update 19.01.2026:
Skadis insert for AMS wall mount
Left and right versions included in the profile
Check out my Skadis collection if you're looking for accessories to hang up 😉
Update 09.01.2026:
AMS HT for H2x-series_V2.1
Model & print profile adjusted for improved stability
Update 13.11.2025:
Holder for AMS HT is now also compatible with Skadis
2 print profiles available:
2-piece version for A, P, and X series
1-piece for the H2 series
Holder can be mounted on the wall as usual or attached to Skadis using the hooks
When using the holders on the Skadis, the hooks should be secured with a little glue!
There is another model for accessories in the drawer system P(1) & X series.
What bothered me about the Skadis was that the original brackets or those printable on Makerworld always took up a little of the usable space and you couldn't hang anything there. That's why I created another model for an alternative mounting option. A drilling aid and single or double spacers in various lengths.
You can find the profile here:
Update 10.11.2025:
Adapter V3 to Skadis is online 😉
A total of 4x M4 nuts & 4x M4 countersunk screws (length 12-16mm) are required. The original bracket (version 3) is screwed on and then attached to Skadis in the same way as the current V4.
Update 06.11.2025:
Version 4:
> Compatible with IKEA Skadis
> Less filament with more stable construction
> Improved coupling and cable management
The holder can be mounted on the wall as usual or attached to Skadis using the printed hooks. The drilling pattern and spacing remain unchanged. The accessories can also continue to be used as normal 😉
The coupling has been modified and thus reinforced once again. The alignment and print profile have also been adjusted. The cable management has also been modified.
When using the holders on the Skadis, the hooks should be secured with a little glue!
Update 06.10.2025:
The next extension is a horizontal spool holder for mounting under the AMS:
Spools up to ~80mm can be accommodated.
Installation is carried out using the existing “Extension AMS wall mounting”
You can find detailed assembly and operating instructions as a .pdf below
Let me know if you have any further suggestions or requests 😊
Update 08.09.2025:
Following a small suggestion from a user, the next extension is now available. You now have the option of combining the drawer system and the 3-fold or 5-fold plate holder.
This means you can use both extensions under one AMS.
Thanks @tambo4 for the tip 👍
Update 30.06.2025:
Plate holder for the print plates for the H2D supplemented
Available in 2 versions:
plate = 5-fold holder for printing plates only
plate = holder for 4 printing plates and an additional large insert for the laser plate
Bambu Vision encoder naturally fits in both versions
The holder is simply inserted into the existing Extension AMS wall mounting. No new mount is required!
Special thanks to @Ludd3 for the test prints, feedback with the photos used and patience 😁
You can also find the profile separately.
…
Update 18.06.2025:
Bracket for the AMS HT added 😁
You can find the print profile as 2-piece or one-piece for the H2D as usual above ^^
The holder has a cut-out on the back where the cable and PTFE tube can be laid. Both ventilation openings of the AMS HT (when dry) are free and the air can escape easily. The height of the hole spacing has of course remained unchanged. The side opening is also exactly the same - so the honeycomb insert can still be used.
In addition, the holder has optional accessories that can be added directly without having to print an extra holder for them!
First there is a drawer system with organizer for e.g. nozzles, glue sticks, kits etc...
You can also find the profile separately.
…
Update 31.03.2025:
Version 3.2:
Tolerance of the 2-piece holder has been reduced to ensure a better hold of the two parts
another one-piece print version has been added for the H2D
also compatible with the new AMS 2 Pro!
Update 03.02.2025:
Description adapted
Added print profiles for accessories
I have removed the print profile for version 1 & 2 after some consideration → the current version 3.x is flatter and the filament rolls off better - in addition, the current & future attachable accessories are only compatible from V3 (if someone still needs the old print profile, please feel free to contact me!)
Version 3.1:
After a number of community comments, we considered creating another flatter version. The angle was changed from 35 degrees to 20 degrees and more distance to the wall was created.
This made the model too large for the printing plates. I created a coupling point to get the model onto a plate. The connection can easily be glued afterwards.
With the smaller angle, there should be no further problems when unrolling the filament. I have already replaced my holders with the 3rd version and am very satisfied.
The base plate and mounting holes have of course remained unchanged. No new holes need to be drilled!
Furthermore, a guide for the PTFE tube was inserted. Thus, the tube can now be laid cleanly.
Accessories for the AMS & AMS 2 Pro:
(all print profiles can be found separately above ^^)
Honeycomb insert:
The variety of hooks, holders and co. is almost endless 😁
… you have the choice!
Extension AMS wall mounting:
Base plate for attaching the accessories.
Printed in 2 parts, it is simply plugged together in the middle. Gluing is not necessary!
Installation is also completed in just a few seconds:
AMS plate holder:
The plate holders are simply inserted into the base plate.
Available for 3 & 5 print plates.
Drawer carrier :
Drawer system with 2 drawers for tools, accessories and co.
Optionally, individual inserts in different sizes can be used.
The lettering is of course freely adjustable in the slicer.
Do you have any other ideas or wishes? Please let me know 😊
Have fun printing 😎
If you like my models and profiles, you can support me with these options:
Leave a Like 👍
Leave a comment ✒️
Download the file ⤵️
Boost the model 🚀
or buy me a coffee ☕😊
This model & print profile as well as the finished print may not be used for commercial purposes. Unless, of course, you are in possession of an active license (offline or online).
Membership
Commercial license available for sale via MakerWorld.
Join
For more models, please have a look at my profile…
If you want to use this model commercially, please join my membership.
Join Now
This user content is licensed under a Standard Digital File License.
You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.
Comment & Rating (6014)