Easy Adjustable Speed Rechargeable Rotating Display Stand - Free 3D Print Model

Search models, users, collections, and posts

Remixed by

fycds

Tools>Hand Tools

IP Report

Print Profile(2)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 3 walls, 8% infill，适用于A1-mini打印

Designer

6.1 h

2 plates

4.7(10)

Fully enhanced and beautified version 20250419 (see pictures) A1 mini printable

13 h

6 plates

5.0(1)

Open in Bambu Studio

Boost

162

302

343

107

Released

Description

Content has been automatically translated.

Show original

A simplified 3D-printed rotating display stand, inspired by Thingiverse's 3DPrinterArt, this remix simplifies the speed control mechanism, utilizing an inexpensive DC motor speed controller, eliminating the need for programming, and incorporating a lithium battery charging module for convenient recharging. It adequately fulfills the needs of showcasing artwork and manual spray painting.
Required Parts List:

Part numbers correspond to the diagram. All parts are readily available online, with a total cost under 20 RMB.
1. KCD1 Miniature Rocker Switch (15*21mm) x1, 1 RMB
2. Single-Axis 130 Gear Motor (220:1 Gear Ratio) x1, 4 RMB
3. 1.8~12V DC Motor Speed Controller with Knob x1, 4 RMB
4. 18650 Battery and Battery Holder x1, 6 RMB
5. TP4056 Lithium Battery Charging Board x1, 2 RMB
6. 608ZZ Bearings x4, 2 RMB

Update Log:

2024.11.26 Added circuit wiring diagram

Boost Me (for free)

If you like it, please click the FREE boost button -->
Thanks for your kind support!
If you appreciate my design, please click the free boost button on the right -->
Your support fuels my continued progress, thank you very much!

Comment & Rating (40)

@noker

The model is excellent, thank you, author I printed a set and made enhancements, see my published enhanced accessory print profiles for details The original model has some minor issues, listed below, if you have time, you can correct them :) 1 The motor slot obstructs the insertion of the bearing dowel, the wall height of the motor slot can be lowered slightly 2 The diameter of the dowels for the three lower bearings is a bit small, there is a risk of slippage after insertion, it is recommended to increase the diameter of the three bearing dowels to 7.9mm 3 The motor slot cannot accurately position the motor, it needs to be adapted manually (a 3mm top cover gear can be printed to determine the motor position) 4 The bearing base slightly hinders the speed control module, in addition, the recess on the outside of the speed controller opening can be made larger for easier tightening of the lock nut Personal suggestions for reference only, thank you again for sharing this model :)

(Edited)

The designer has replied

Show original

@fycds

Thank you for your suggestions: 2. The axis can be adjusted according to material shrinkage, 3. The dimensions of stepper motors sold by different vendors may vary slightly, the motor can be firmly secured in the motor slot using double-sided tape

Show original

@AQR_0124

Hello, could you please share the revised bottom shell The submitted 3mf file only contains two accessories, and they do not fit the author's original bottom shell

Show original

@noker

Replying to @AQR_0124 :

As per your request, I have updated the full version of the print profile (which I originally did not intend to release) The version you see now has been significantly adjusted and enhanced compared to the previous one, and it is also the version I currently use myself Please check out the new version on the page I hope you like it :)

Show original

@Passuncao

Print Profile

0.2mm layer, 3 walls, 8% infill，适用于A1-mini打印

Works Perfectly!

The profile uploader has replied

@fycds

thanks for your review

@CJjim3D

Print Profile

0.2mm layer, 3 walls, 8% infill，适用于A1-mini打印

It makes a slight rattling sound

The profile uploader has replied

Show original

@fycds

Plastic gears produce unavoidable noise, please add lubricant

Show original

@sacha69140

Boosted

Hello, would you have a detailed photo of the wiring

The designer has replied

Show original

@fycds

i will add this soon

@sacha69140

Boosted

Replying to @fycds :

Thank you very much I bought and printed everything it's a very beautiful model

Show original

@fycds

Replying to @sacha69140 :

circuit connection diagram is added, check the last picture. Enjoy it.

@fycds

If you need more detailed information, please leave a message

The designer has replied

Show original

@fycds

Replying to @marek.wydysz :

what's the motor type used in kit005? any lable on it ?

@fycds

Width of the motor is about 22.5mm

@clarks58

came out great thx. already had all the electrical and bearings in stock. I spent 55 years collecting anything i could think so I have when I need. only question is. would you consider installing a C usb hole for the ones with 2 wires. for now drimel is my best friend. lol thx 😊

The designer has replied