Apex Deathbox | Apex Deathbox | Storage Box - Free 3D Print Model

Search models, users, collections, and posts

ACENX Studio

Toys & Games>Other Toys & Games

IP Report

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

All colors separated 0.2mm layer, 2 walls, 15% infill

7.5 h

3 plates

5.0(12)

Open in Bambu Studio

Boost

248

680

435

170

Released

Description

Apex Deathbox Fan art 3D prints

Warm hello to Maker World community, I used Autodesk Inventor to build this 3D model as a fanart for Apex Legend. I have been playing this game for years, not a lot these days but it left some good moments in my memory.

!!! Please do not use for commercial purpose or upload to other platforms !!!

All parts are detached prints and needs to glue on
Print parts by color can save some filaments
Print with less dense support for easier removal
Apply glue on the print bed to avoid curly edge
Adjust Scale freely to suites your needs

APEX

Apex Legends

apex legends death box

Comment & Rating (29)

@user_3198918809

Boosted

Print Profile

All colors separated 0.2mm layer, 2 walls, 15% infill

Scaled quite a bit to fit the Bloodhound heirloom and shield cell inside. Added some LEDs and I made the tile for the top (tape to hide GT). 8 plates total after cutting it to fit my P1S at the scale. Thank you for the model! My friend was amazed with the final result. Shield cell here: https://makerworld.com/en/models/810696#profileId-769831 Bloodhound heirloom here: https://www.thingiverse.com/thing:4787800 Top tile: Badges from Etsy and Bloodhound (https://www.thingiverse.com/thing:6039098)

@ACENX

Hi Norrec, thank you for your comment, this looks amazing and the quality is sooooo gooooood!!! LOVE IT!!!

@dragonlion14

That looks amazing! What percentage did you use? I would love to print it in this size!

@user_3198918809

Boosted

Replying to @dragonlion14 :

Hey mate. I didn't save the scale but my x-axis (width) for the bottom of the case was 536mm in total. So you should be able to use that with uniform scale on, get the percentage and apply it to all the pieces. I cut the lid and bottom into 3 pieces each to fit my P1S plate. Tricky part was adding in pin holes to those 6 pieces so that I could make it stronger and not snap apart if it was dropped. Good luck! Share pictures if you end up doing it :)

(Edited)

@Mouselab

Boosted

Scaled it up to 135%, and it worked perfectly—turned out great! Really appreciate the creativity and effort!

The designer has replied

@ACENX

Thank you Mouselab, this looks very awesome!

@malisandr3

Replying to @ACENX :

can it be used as a carrying case for dice and card games or is the clasp just decorative

Show original

@user_3747867554

this is fake

The designer has replied

@ACENX

Hi IDOGYMNASTICS, thank you for your comment, it looks like the printer did not leveled correctly before printing the model or the print bed was no hot enough to stick the first layer. Try re-level the print bed and do a quick test print before printing out the actual model. Let me know if this helps.

@user_3747867554

I’m sorry. I printed this on a Bambu A1 Mini and it looks like there is not a profile for this to be printed on the A1 Mini so I suspect that was the issue.

@ACENX

Replying to @user_3747867554 :

All good! I just saw the message, have you printed it successfully afterwards? I don't have a Bambu printer yet so can't help with the profile ;-; , but for general issues I might be able to help!

@GBeeeeem

Boosted

I tried painting it to give it a battlefield feel Seeing someone use the hinge below, it seemed better, so I might have to go buy a hinge haha The result is absolutely superb

The designer has replied

Show original

@ACENX

Thank you and happy to see that you like it! Awesome work!

@sparowes

Print Profile

All colors separated 0.2mm layer, 2 walls, 15% infill

Made this as a surprise for my spouse. I expected the latch pieces to be fiddlier than they were, but it all came together pretty easily. Thank you for the model.

@3d3dhorizons

Boosted

awwwwwsommmmmeeeee

The designer has replied

@ACENX

thanks hahahahah

@junkeruwe89

Print Profile

All colors separated 0.2mm layer, 2 walls, 15% infill

Top model, it was a birthday gift and was very well received

Show original

@Ichanity

Did you create the top part with the names, for the deathbox?

@don_design.

Print Profile

All colors separated 0.2mm layer, 2 walls, 15% infill

awesome print can't wait to show it off at school😂

@sooper

Print Profile

All colors separated 0.2mm layer, 2 walls, 15% infill

Solid Print. Everything fit together!

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.