Turbo Base for Air Filter Lamp 001 - Free 3D Print Model

Search models, users, collections, and posts

Ocular Dynamic

Household>Decor

IP Report

Print Profile(2)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

Cold Side Only - 0.2mm layer, 2 walls, 15% infill

Designer

6.9 h

2 plates

4.7(15)

Full Turbo - 0.2mm layer, 2 walls, 15% infill

Designer

14.4 h

1 plate

5.0(4)

Open in Bambu Studio

Boost

526

1014

662

165

Released

Bill of Materials

Maker's Supply Kits and Parts

Select all

LED Lamp Kit Collection

Description

I've always wanted to make a turbo lamp for my garage that featured a cone filter attached to it properly like it would be in real life. Having come across Sanja 3D's Air Filter Lamp I figured I could make a nice turbo base that utilized his lamp.

Printing the full size turbo, because of the height, will have to be printed on the bigger beds. I did create a separate profile with the turbo cut in half so its just the cold side that fits the A1 Mini bed. This also saves a bunch of material and has a lot less supports. Supports can be annoying to remove as always, but they should come off pretty easy.

Assembly is as easy as dropping the coupler piece over the inlet on the turbo (rough side down, flat size up) and pressing the fully assembled Air Filter lamp inside the inlet of the turbo. You can run the wire down through the middle of the turbo and out the bottom. This gives the Air Filter Lamp the look of being connected to the turbo via a silicon coupler. You could even use TPU for the coupler to make it look more like a silicon hose, only thing it'd be missing is worm clamps.

Grab Sanja 3D's Air Filter Lamp Here. Works great with the Bambu Lab Lamp Kit 001

Boost Me (for free)

Boost if you're also a car guy

Comment & Rating (40)

@Maror

Great job dude, I printed the whole turbocharger and it came out great!

The designer has replied

@OcularDynamic

Awesome!

@sgamo

How did you make the cable ties

Show original

@user_1573526995

Fantastic model, thank you!

The designer has replied

@OcularDynamic

nice touch with the clamps, looks great

@TERRAVIO

Print Profile

Cold Side Only - 0.2mm layer, 2 walls, 15% infill

super print

The profile uploader has replied

@OcularDynamic

Looks great!

@Art3D_Creations

Print Profile

Cold Side Only - 0.2mm layer, 2 walls, 15% infill

I love it, incredible

Show original

@sgamo

Print Profile

Cold Side Only - 0.2mm layer, 2 walls, 15% infill

@NTH_Designs

Print Profile

Cold Side Only - 0.2mm layer, 2 walls, 15% infill

great idea however the low resolution of the model with low poly count for the curved faces makes the model look not very appealing

@phroztbyte

is it just a really tight fit? it seems like the square area in the bottom of the filter doesn't allow the filter to go down into the turbo inlet. or am I just really stupid?? haha

The designer has replied

@OcularDynamic

I'm not sure what you mean. There is nothing square. The bottom of the filter (im assuming you mean the part the light goes in to) is round? But yes that part fits into the inlet of the turbo

@phroztbyte

Replying to @OcularDynamic :

that is what the base of the filter looks like. see how it isn't perfectly round?

@OcularDynamic

Replying to @phroztbyte :

Did you get that from Sanja 3D's model listing? Looks like you used the plate 2 from his LED bases profile. You'll want to use Plate 3 thats for the Bambu Lab LED Lamp Kit 001. You can also get that base from Bambu Labs LED Lamp Kit 001 listing as well. Are you trying to use an LED Strip? If so i can make a base similar without the squared section his has. I was using the LED light from the Bambu Lab kit so thats the base I designed it for. It's no problem to make a base for the a strip led tho

@WeArelost

What infill pattern do you use

The designer has replied

Show original

@OcularDynamic

I think it was cross hatch or similar, I can't remember at this point. prob whatever the initial infill is when you open bambu studio

@WeArelost

Replying to @OcularDynamic :

I have seen it and it has a grid type Thank you

Show original

@sgamo

did you insert the filter's LED strip base how did you solve the protrusion at the base that is not round

The designer has replied

Show original

@OcularDynamic

Use the base labeled as "original" the base for the LED Lamp 001 kit light. It latches in to the bottom of the base of Sanja's Lamp. This wont work for his LED Strip bases with the protrusion. To use those bases you'd have to round off that protrusion and add a hole for your wirings to pass through the bottom.

(Edited)

@sgamo

Replying to @OcularDynamic :

In the end I created the base from scratch to fit better in the turbine as soon as the print finishes if everything is okay I will publish the modification if it can be useful to someone

Show original

@Pfaelzerus

Would it not be possible to design it somewhat more rounded?

Show original

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.