Centrifugal Pump - Free 3D Print Model

Search models, users, collections, and posts

Renegade 3D

Tools>Other Tools

IP Report

GIF

Print Profile(1)

All

X1 Carbon

P1S

P1P

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 5 walls, 45% infill

Designer

13.1 h

6 plates

4.5(6)

Open in Bambu Studio

Boost

102

262

203

Released

Description

I present to you the 3D printed Centrifugal Pump.

All parts were created using PLA and TPU for the two gaskets. The pump has been tested and does actually work. The impeller shaft was modeled to fit a 17mm socket and powered by a drill of some fashion. I am currently working a remix of this that will be able to be powered by compressed air as well. There are two pauses when printing the housing, the first is to insert the square nuts for the lower plate assembly, the second is for inserting the square nuts for the upper inlet assembly.

The following components were purchased from Amazon:

Bearing - ［12 Pack］6001-2RS Ball Bearings – Bearing Steel and Double Rubber Sealed Miniature Deep Groove Ball Bearings for Motor (12mm x 28mm x 8mm)

Socket Head Cap Screws - 100pcs M3 x 12mm 12.9 Grade Alloy Steel Hex Socket Head Cap Screws Bolts,Black Oxide Finish

Square Nuts - 200 Pieces 304 Stainless Steel M3 Square Nuts

The impeller shaft and impeller are glued together and the bearing is press fit and glued to the bottom plate of the housing.

As always constructive criticism is appreciated. Enjoy!

Documentation (2)

Assembly Guide (2)

Cetrifigal Pump.pdf

GIF

IMG_2209.gif

Comment & Rating (13)

@MyWorld3D

Print Profile

0.2mm layer, 5 walls, 45% infill

It's not very practical to use. It can't suck up water; it only works when submerged. If you connect a hose or pipe, it won't draw water at all.

@user_2560268528

Print Profile

0.2mm layer, 5 walls, 45% infill

@polymerprinting

Boosted

Great design!

The designer has replied

@mklathrop84

thank you, I put quite a bit of time into this one. I appreciate the support

@emanuele.10392

Print Profile

0.2mm layer, 5 walls, 45% infill

@Patrix2026

Hello, can you please put your 3mf file in stl, please I am limited with my software and I would like to adapt the rear shaft plate with my motor thank you

Show original

@San4o_Pan4o

Boosted

I'm printing right now and I'm very excited 🤩 what happened to the pneumatic version project

Show original

@aysarkpro

Great design, can you test if it works in pumping water up? can it go as high as 6ft? Also would this design work in a manual no-power situation where one would use a handcrank?

(Edited)

@Georg1590

Hello, is the compressed air version available yet

Show original

@hadan8088

Haven't printed yet but I think this is exactly what I need to pump the water off the pool filter in the spring. I'm excited to have found it!

@user_3618777951

Print Profile

0.2mm layer, 5 walls, 45% infill

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Centrifugal Compressor

CATIAV5FTW

1.2 k

395

Centrifugal Air Blower

kjt270000

1 k

370

1.8 k

538