Hairbrush - Free 3D Print Model

Search models, users, collections, and posts

Staprin3D

Household>Other House Models

IP Report

Print Profile(2)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.16mm layer, 2 walls, 15% infill

Designer

2.3 h

2 plates

4.4(41)

0.16mm layer, 2 walls, 80% infill PETG Transparent/PETG-HF

2.6 h

2 plates

4.4(5)

Open in Bambu Studio

Boost

359

760

1 k

617

Released

Description

Content has been automatically translated.

Show original

Here is my design for a hairbrush that is easy, fast, and cheap to print

The bristles are simply pushed into the brush body and then the brush is closed with the end piece

The end piece must be tilted slightly for assembly and can then be pressed into the brush body

This has the advantage that the bristles can be easily replaced if needed

Attention: When assembling the bristles, the raised part on the bristle foot must point to the right when inserted into the brush body

There are beautiful optical effects when the bristles are printed in two colors

For example, you can print a color-customized brush for each child

Best printed in PETG or PETG-HF

Have fun

Boost Me (for free)

If you like the design, I appreciate a 'boost me'

Membership

By signing up as a member, you receive permission to use physical prints of my models for commercial purposes.

Join

© Staprin3D

Comment & Rating (65)

@user_2306180697

Print Profile

0.16mm layer, 2 walls, 15% infill

The only complaint I have is that the tab to lock the brushes broke immediately 🤣 but it's still functional, in the end, a lock wouldn't even be necessary, it's more for aesthetics than utility

(Edited)

Show original

@AMFprints

Print Profile

0.16mm layer, 2 walls, 15% infill

Other Issues:cant insert the brushes as the tolerance isnt good enough

Strength Issue:brushes breake while inserting

The profile uploader has replied

@Staprin3D

Hello, what material did you use and did you use the same material for the brush body and bristles? If not, it is possible that the tolerances are too tight due to different shrinkage.

@AMFprints

Replying to @Staprin3D :

hi i used same material but diffrent colors , pla

@Staprin3D

Replying to @AMFprints :

ok, normally it also works with PLA (Bambu), but maybe try PETG or even better PETG-HF. Maybe reduce the printing speed a little and layer height max 0.16mm

@user_3667014552

Boosted

I didn't expect it to print so perfectly, I hope it's durable

Show original

@user_3694385572

Print Profile

0.16mm layer, 2 walls, 15% infill

It turned out great Fun project to print

Show original

@666Designs

Print Profile

0.16mm layer, 2 walls, 15% infill

a bit scratchy and stiff, but everything fit perfectly

Show original

@sky3darg

the pink part in PLA and the purple part in TPU (PLA-flex) the brushing for someone with long hair is acceptable, very good design

(Edited)

Show original

@Gh14Cc10

Print Profile

0.16mm layer, 2 walls, 15% infill

wow!!

@tech2nology

Print Profile

0.16mm layer, 2 walls, 15% infill

Kind of works. But it's hard to put together.

@KhKhreations

Print Profile

0.16mm layer, 2 walls, 15% infill

I LOVE the overall concept. The main challenge for me was that the bristles were too weak to get them off my textured bed. Over half ended up with bent or broken bristles before I even got to insert them into the brush. Since I think the design is fabulous, I went ahead and changed increased the sparse infill density and crossed my fingers. It worked! All pieces made it off the print bed. I'll add the print profile in case anyone else had the same problem. The bristles were tough to insert (a good thing!) even before increasing the infill. I was careful to make sure the grooves matched before inserting the teeth AND would try a different set of teeth if one was difficult OR tried the teeth in a different slot. I had to go VERY slowly. If my fingers were further away on the teeth OR if I applied pressure on the teeth vs. the "spine" then the strip of teeth would try to bend. I won't install the end piece because my daughter tends break bristles so I'll want to change them out easily.

@user_711774415

Very nice and useful!

License

If you want to use this model commercially, please join my membership.

Join Now

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Minimalistic Hairbrush Holder

284

Retractable Hairbrush V3

ChristianH

6.2 k

3.4 k

Holder for Hairbrush

Karliblue

271

179