Poop grabber - Free 3D Print Model

Search models, users, collections, and posts

Corco Design

Household>Pets

IP Report

Print Profile(2)

All

P1S

P1P

X1 Carbon

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

A1 mini

0.2mm layer, 3 walls, 20% infill

Designer

6.1 h

4 plates

4.3(30)

0.2mm layer, 3 walls, 20% infill, 6 plates

8.6 h

6 plates

4.6(5)

Open in Bambu Studio

Boost

1336

3032

1.3 k

451

Released

Bill of Materials

Maker's Supply Kits and Parts

Select all

Compression Spring

Description

The Poop Grabber is a practical and easy-to-use solution for picking up after your dog during walks. This 3D-printed grabber is designed for convenience and hygiene collecting waste without getting too close or dirtying your hands. Its lightweight and ergonomic design make it easy to carry, while the efficient gripping mechanism ensures a clean pick-up every time. An added feature of the Poop Grabber is a built-in compartment for holding waste bags, so you’re always prepared on the go. No need for extra accessories—this tool combines everything you need in one compact, easy-to-use design.

The Poop Grabber is the perfect companion for any dog owner, offering a quick and simple way to keep your surroundings clean. Whether you’re on the go or cleaning up at home, this tool ensures you’re always prepared.

How to Use:

Remove the back cover and insert a roll of bags, threading it through the opening. The bag should stick out from the bottom of the grabber. Put the cover back on
To collect poop, pull the bag so that the end is positioned near the tips of the legs.
Pull the handle to close the legs.
Flip the bag over, securing it with the clips, or stretch it over the entire legs (stretching it is quicker).
Open the legs.
Pick up the poop by pulling the handle.
Tie the bag, tear it off, and dispose of it properly.

Documentation (1)

Assembly Guide (1)

Poop Grabber Assembly Guide 2.0.pdf

Comment & Rating (87)

@YtyMcSkeetertin

Boosted

Print Profile

0.2mm layer, 3 walls, 20% infill

Great bit of machinery! Makes picking up poop fun. I had to plastic weld some of the clips together for increased rigidity - they were breaking out. Now I am having issues with the snap in rings but that's probably just from using PLA. I don't use the springs and wish there were little indentions on the sides for gripping and releasing the claw. If i print again i will throw down a remix with the indentions.

@user_461186525

works good but i have an issue with the locking mechanism, it doesn't seem to work well

(Edited)

@user_3109508733

That's really cool! How did you design a new logo?

@WolfShadowheart

Replying to @user_3109508733 :

it's been some time and I'm not that user, but I typically add a cube to remove the old face that I don't want, and then I use an SVG of the design I want as a modifier

@HEADS3D

Boosted

Hello do you have an explanatory video assembling the device From section 7 onwards I don't understand anything regards

The designer has replied

Show original

@corcorano

Hello! Unfortunately, I don't have an assembly video, but I'll try to help as much as I can. Are you referring to point 7 of the manual? If so, you need to insert the part called 'pusher pin' into the 'spring holder' part, and then insert the spring. Once assembled, place this pushing mechanism into the inner handle. There’s a bit of extra space there, so the part might initially try to pop out, but once you push the inner handle into the outer handle and finish assembling the grabber, the mechanism will stay securely in place. I’ve also attached an illustration and a cross-section of the fully assembled mechanism, which should help clarify things. If you have any more questions, feel free to ask!

@HEADS3D

Boosted

Thank you very much for your reply, I also have questions regarding sections 9, 10, 11, 13, 14, could you clarify how to do it I don't know how to use the smaller pieces or where to put them, I don't quite understand the image in section number 9 of the manual Regards

Show original

@corcorano

Oh 😅 In that case, I’ll update the manual and expand the sections you mentioned. I’ll let you know once it’s ready

@Datadude

does the bag get held by the clips on the legs?

The designer has replied

@corcorano

Yes, the clips can hold the bag. However, it takes a moment to attach it, and after some testing, I found that simply wrapping the bag around the entire legs works just as well.

@JustKeepCreatin

Replying to @corcorano :

ok now I get it and love this!!!

@user_3237136218

Does it handle soft mushy poo too? Or when you don't get all the nuggets in the first grab.

(Edited)

@Sir_goof_a_lot

Print Profile

0.2mm layer, 3 walls, 20% infill

Absolutely nothing but issues printing. Plate one was fine. Attempted plate 2- three times. Fail. Nothing but stringy messes. Nothing is working to fix.

@user_461186525

if you are having trouble with one of the side pieces, I had the same problem. I found that the first layer only covered half of the piece. I used the cut tool and cut the first layer off. it worked great after that

@user_3190286198

Hello, I have the same issue; I just thoroughly cleaned my plate and restarted the process for the third time

Show original

@user_3010708529

maybe need to buy a new heating element my prints came out perfectly

@user_4202103578

The panel on the second tray was not flush which easily caused failures I resolved this issue by adjusting the contact area The screws were too short a problem I fixed through redesign Everything else is excellent thank you for sharing this design

Show original

@Sir_goof_a_lot

PLEASE share how you fixed plate 2. I'm beyond frustrated trying to get it to print. Thank you.

@user_3184125460

Should I print this part with tpu ?

@Sn0rrii

Boosted

Print Profile

0.2mm layer, 3 walls, 20% infill

i like it. very cool idea.

@Fritz85

Print Profile

0.2mm layer, 3 walls, 20% infill

Funktioniert super

@Ray_XDDDDD

Print Profile

0.2mm layer, 3 walls, 20% infill

The claws are a bit tight and don't release automatically, but otherwise it's quite good

Show original

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Fidget Grabber Long

shol

18.9 k

4 k

GIF

Little Robot Hand

Patopato_Design

30.7 k

8.9 k

Poop Bucket - A1- A1 Mini

Recko

27.2 k

4.4 k

H2D / H2S / H2C Poop Chute

Maxx Design

18.1 k

1.8 k