WZ-551 6X6 infantry fighting vehicle中国92式轮式步战车

Please be sure to comply with your local laws and do not use the model for inappropriate purposes.This is a cosplay prop.

Thank you to everyone who provided me with the photos.

The WZ-551 (ZSL-92) is a prototype Chinese Armored Personnel Carrier that appears in Wargame. The ZSL-92 wheeled armored vehicle, codenamed "WZ551", also known as the "Type 92 armored personnel carrier", is a 6×6 wheeled armored transport vehicle developed by China. It was equipped in the mechanized forces of the People's Liberation Army of China in the mid-1990s. The chassis adopts an isometric 6×6 drive mode. Passengers enter and exit through the rear door and side door. There are two ducted propeller propulsion devices at the rear of the vehicle body to improve the ability to move on water. Initially, the WZ551 was equipped with a single-person turret (weapon top) with a ZPT-90 25mm caliber machine gun. The standard weapon of the ZSL-92A is a Type 88 12.7mm caliber anti-aircraft machine gun, and it can also be equipped with various diversified weapons according to different uses.

I made this model in Fusion 360. To facilitate 3D printing, some details are not shown or are not strictly in proportion. Please use glue to glue the parts together. Press the turret into the car body. If it is too tight, you can use a heat gun to slightly heat the lower body clip.

WZ-551 is a Chinese Armored Personnel Carrier prototype that appears in Wargame. The ZSL-92 wheeled armored vehicle, code-named "WZ551", also known as the "Type 92 armored personnel carrier", is a 6×6 wheeled armored transport vehicle developed by China. It was equipped in the mechanized forces of the People's Liberation Army of China in the mid-1990s. The chassis adopts an isometric 6×6 drive mode. Passengers enter and exit through the rear door and side door. There are two ducted propeller propulsion devices at the rear of the vehicle body to improve the ability to move on water. Initially, the WZ551 was equipped with a single-person turret (weapon top) with a ZPT-90 25mm caliber machine gun. The standard weapon of the ZSL-92A is a Type 88 12.7mm caliber anti-aircraft machine gun, and it can also be equipped with various diversified weapons according to different uses.

I created this model in Fusion 360. To facilitate 3D printing, some details are not shown or are not strictly in proportion. Please use glue to glue the parts together. Press the turret into the car body. If it is too tight, you can use a heat gun to slightly heat the lower body clip.

2024.9.6:

I am very sorry. I exported an incorrect version before, which caused problems with the axle hole of the left rear wheel. Thanks to my friends for their feedback. I have repaired and uploaded it again. I apologize for the loss caused. For the previous printing errors, you can use a soldering iron or drill to drill holes. Because they are hidden behind the wheel, they have little effect on the appearance.

I am very sorry. I exported an incorrect version before, which caused problems with the axle hole of the left rear wheel. Thanks to my friends for their feedback. I have repaired and uploaded it again. I apologize for the loss caused. For the previous printing errors, you can use a soldering iron or drill to drill holes. Because they are hidden behind the wheel, they have little effect on the appearance.

Please be sure to comply with your local laws and do not use the model for inappropriate purposes.

Under the new reward mechanism, please "Boost Me" more, give me five-star praise, and welcome everyone to share and show off their finished works, so that I can get more points. Your support is my biggest motivation to continue designing more models.

Reminder:

• Different filaments may cause the parts to be too loose or too tight, and may also make some supports difficult to remove.
• The position of the model printing takes into account strength and appearance (for example: vertical surfaces have better fineness and better representation of patterns and text; horizontal printing axes sacrifice accuracy but have better strength).
• Please keep the printing plate clean. All models are confirmed to be printable. It's not my fault if it turns into spaghetti.
• It is recommended that you equip yourself with a heat gun. Slightly heating the parts can solve many minor problems and can also compensate for minor part tolerances.