Closed chute for printer waste for (P1P P1S X1) - Free 3D Print Model

Search models, users, collections, and posts

Mc2.project3D

3D Printer>3D Printer Accessories

IP Report

GIF

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 2 walls, 15% infill

Designer

23.5 h

6 plates

4.9(859)

Open in Bambu Studio

Boost

2735

6765

1147

1.3 k

11.2 k

5.6 k

Released

Bill of Materials

Maker's Supply Kits and Parts

Select all

M3x10 SHCS Machine Screw (20PCS) - AA159

M3 Socket Head Cap Machine Screws (SHCS)

Description

Boost Me (for free)

Support my work, I do my best.

I created this slide to improve on the ones I've seen on this platform. (NUOVA REVISIONE 04/SEPTEMBER/2024)

There are two types of models:

for printer positioned on standard feet
for printer positioned on anti-vibration feet.

The chute must be printed flat and large quantities of supports are not needed, this way you will have a much smoother wall where the excrement can flow.

This will allow you to print it at higher definitions without affecting performance.

Furthermore, I created a closure that will allow you to maintain a constant temperature inside the chamber.

The basket is removable and easily installed.

Designed with Fusion 360

(NUOVA REVISIONE 02/SEPTEMBER/2024)

V2 Changed the aesthetics of the detail in the photo.

Added small, medium and large container

CONTAINER SMALL

CONTAINER MEDIUM

CONTAINER BIG

Good print from MC2.project3D

Documentation (1)

Assembly Guide (1)

Assembly guide.pdf

Comment & Rating (1147)

@RicoSteam_3Dp

Print Profile

0.2mm layer, 2 walls, 15% infill

Other Issues:the model is essentially well made and reading all the other comments, I think I'm the only one having problems.. with the X1 it happens too often that the skein is unable to slide down the slope. it gets stuck at the starting point, congesting the duct.in a 5-hour multi-color print I had to manually clear the duct about ten times.

@aMJay99

It looks nice but the ramp entrance is designed too narrowly, causing it to get stuck multiple times The large tray bin is also too small I am considering detaching and discarding it

Show original

@aMJay99

You are not alone. I removed this print and discarded it

Show original

@user_3992732586

Boosted

very clean & elegant HOWEVER (my bad…) I failed to realize it works ONLY with AMS because it blocks my filament spool … such a clever “upsell” 🤣

@user_2986060550

I'm not sure that it's your bad - I've come across the same problem. I've then looked through the descriptions and can't find mention of the fact that it is AMS compatible only anywhere. I'm a bit annoyed after a full day's printing.

@rafael2020

Replying to @user_2986060550 :

Maybe you can print a side spool holder, I initially printed this one and worked fine: https://makerworld.com/en/models/236809-side-spool-holder-for-p1s-x1c#profileId-277146 Later I bought a Creality Space Pi Plus, and now I use it as a spool holder when I don't need to dry filament.

@bpivk

Boosted

It seems that they have changed something. It doesn't fit. It works but I can't get it flush.

The designer has replied

@mc2.project3D

You will have printed the original foot model

Show original

@bpivk

Boosted

Replying to @mc2.project3D :

No I don't. I have double checked and it's the correct model. 240 height vs 230 in the original. I have added some legs below and it's ok now. I also thought that I had messed the print up and printed the wrong print so I've measured and checked both parts and it's the correct one. I can attach a photo if needed.

(Edited)

@mc2.project3D

Replying to @bpivk :

Have you seen the updated version, how beautiful it is

Show original

@Donnerhall

Boosted

A truly splendid model, thank you so much! I sectioned the model in the slicer and incorporated a dovetail joint. This allows for occasional opening of the shaft and, importantly, enables reattachment of the spool to the spool holder when printing without the AMS

The designer has replied

Show original

@mc2.project3D

Hello, thank you, I have created a similar model that addresses this issue, please take a look

Show original

@Donnerhall

Boosted

Replying to @mc2.project3D :

Oh, this is even more beautiful! I will also print this. Thank you very much!

Show original

@mc2.project3D

Replying to @Donnerhall :

thanks to you

Show original

@javier.parisbla

Boosted

Perfect One part from version 1 and another part from version 2 Thanks

The designer has replied

Show original

@mc2.project3D

Exactly there is no problem in version 1 the slide has different aesthetics

@user_1340847654

It would be nice to have an option for a longer connected one, it makes it easer to remove and connect when we dont have much space

The designer has replied

@mc2.project3D

ok but the piece of filament will never reach the end

Show original

@user_157360631

Worked well for my application, I think some of the support was un-neccesary, but it came off clean enough. Would 100% print this again. (I am not using the spool holder at the back of the machine FYI)

The designer has replied

@mc2.project3D

However, there's also a version for that on my page 😊

Show original

@Sysel94

Print Profile

0.2mm layer, 2 walls, 15% infill

all fits perfekt and functional as well

The profile uploader has replied

@mc2.project3D

thanks

@Petroslav04

Boosted

Print Profile

0.2mm layer, 2 walls, 15% infill

very nice!

The profile uploader has replied

@mc2.project3D

😊

@user_1312075671

Boosted

best print yet.

The designer has replied

@mc2.project3D

🥰🥰

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.